Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

My normal cycle and cancel button lights are blinking on my kitchenaid dishwasher. Model # KUDP02CR8S2 Any suggestions?


Answers :

Probably a keypad gone bad. Try replacing the keypad.

There is a troubleshooting guide behind the foot kick panel. It gives a sequence to test for a bad keypad. You can try that sequence to be sure.
Rinse only and cancel buttons blinking
model kud101fkss0
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My normal cycle and cancel button lights are blinking on my kitchenaid dishwasher. Model # KUDP02CR8S2 Any suggestions?


Probably a keypad gone bad. Try replacing the keypad.There is a troubleshooting guide behind the foot kick panel. It gives a sequence to test for a bad keypad. You can try that sequence to be sure. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

My kenmore dishwasher, model 15822, just stopped working. The quick rinse light is blinking. The only other buttons that work are the pots & pans light which blinks when pushed, and the cancel button which will run through the 2 minute cancel cycle.


These are known to develop sticky switch contact pads. They stick in the contacted position and stifle the panel. Sometimes heat can be applied with a hair dryer to release them and make the unit function again. This is more than likely a temporary f ... Kenmore Dishwashers

I have a whirlpool model KuDSO1FL and the clean light blinks and won't start after the cycle has been selected and the start button is pressed. I have tried canceling the cycle but it won't work. The dishwasher was working yesterday and today it drained once we cancelled the cycle and then pressed start but that is all that we could get done. I don't know what the problem is.


Your appliance's clean light blinking will require a service call. It could be several things indicating a problem that are not serviceable by the home owner. You can try turning the power off at the breaker box, then turn it back on and see if this ... Dishwashers

Kitchenaid dishwasher model KUDS01FL I press normal cycle button and then start button. Normal button stays green does not blink and cycle does not begin.


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

It its a 665-17023 kenmore model dishwasher. The 'normal' cycle light its flashing and I cannot cancel it out or restart any cycles. Basically, the dishwasher will not operate. Thus has happened one before and I managed to somehow press the right combination of buttons to reset, but I don't know what they are. Thanks for any suggestions.


... Kenmore Dishwashers

I have a kitchen aid dishwasher model # kudso1ij and it just blinks the rinse cycle button. if you try to push the cancel button it won't work. when you close the door it blink the 2 for just a brief second then goes back to the dashes. One night it just started on its own. Can you tell me how to reset it or fix this problem.


... KitchenAid Dishwashers

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel button i hear a um noise as if it going to turn on but nothing happens and the light stays blinking. what do you think might be the issue .


Dear friend,\015\012ngfam at you service! happy to assist!\015\012It's an electronic problem!The lights are called codes and need to be diagnoed by a factory service person!!We sell appliances for 65 years an ... Dishwashers

I have a KitchenAid KUDp02FRSS1 dishwasher and it will not respond to any buttons being pushed. The Normal, Light China and Cancel lights continue to blink. I have tried reseting the circuit breaker to power cycle the machine but when I turn the power back on it just continues to blink.


... Dishwashers

I have a kitchenaid dishwasher, SS, model # KUDIO1ILBL6. When you press the ''normal'' button to run it, nothing happens. Tried other cycles and same thing, the green light goes on above the cycle but its just not starting. I tried resetting by opening, pressing high temp scrub then energy saver dry, high temp scrub, energy save dry, then close and hit cancel. Is there any other combo to reset it? or does it sound like something else is wrong? thanks!


... KitchenAid Dishwashers

KitchenAid dishwasher, Model # KUDP021RBS1 - "Normal and cancel lights blink constantly". I had this same problem about two weeks ago so I googled your site and though the solution I found was not exactly applicable to my problem but I tried and that is - Press high Temp, heated dry, high temp and then heated dry and then cancel button and then close the door. Would you believe it worked like a magic wand. But this same problem resurfaced and I am trying all those old tricks but nothing is worki


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

"Runaway Dishwasher" Brand new model#FDB520RHS2 Frigedaire was installed today. It was on normal wash and did 8 washes and rinses. It wouldn't switch to the heat cycle. I hit the cancel button after 2 and half hours of washing and rinsing. The water emptied. I then opened the door and let it air dry...I am upset that it did this crazy thing. Do I have a lemon? What would you suggest???


Ask for warranty repair or replacement. ... Frigidaire PLD4375RFC Dishwasher

1998 KitchenAid Dishwasher model KUDM24SEWH2 - cycle and start buttons light up, but once the water has finished running the machine does not start, but "tries" to start every 20-30 seconds. Selecting Cancel provides the same results. Do I need to replace the control panel? Thanks! Stephen


... Dishwashers

I have a kitchenaid dishwasher model kudio1tjwho. It filled and stopped working. I can not cancel or change the cycle. I press start and it washes for about 30 seconds and shuts off. All the other buttons flash when pressed.


... KitchenAid Dishwashers

I have a GE dishwasher model number GLD55OOLOOWW. It was starting a start cycle and i opened the door to put more dishes in and my finger must have hit a button on the door and now two lights flash off and on and it wont reset itself. It has been on for several hours and still blinking and beeping every so often and unplugging it does not help. Any suggestions how to solve this problem. Thank you.


Try pressing the cancel button ... Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button


That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher

I have a blinking cancel light on model GU1200xtlt1 and will not start in any cycle. Also if I push another button it flashes rinse button and cancel button. Before this it ran in Sani Clean over and over again and I could not change the cycle. I emptied out a bit of water from the bottom because it did not drain also and the water was not smelling too good.


... Whirlpool Dishwashers

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

I have a whirlpool in counter dishwasher model # DU915PWPQ0 serial #FS2536586. The problem i have is the light cycle, green light is constantly blinking. When another button is pressed the heavy and normal cycle lights start blinking and the light cycle, light is illumanated constantly. I have left the power off for 24hrs and when turned on the light blinks again. it will not start any cycles.


Hi Mike...As I said..it flashes 4 times (not 5) 4 times then stops and starts flahung 4 times again. Also, the float is free moving in the tub,\015\012\015\012Any other suggstions??\015\012\015\012Thanks\015\012Dave ... Whirlpool 24 in. ADP5962 Free-standing Dishwasher

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2651 seconds