Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

Getting no water

\015 I turn on dishwasher sounds like the pump is working but i am getting no water,and the water supply is on? could the pump be clogged and how do i fix it.\015

Answers :

The electric valve turns the water on and off. the float switch in the d/w tells the valve when to stop. If the float is stuck on the up position, the valve will not open and no water will come in. The other option is that the control panel is not telling the valve to open. Hope this helps.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Maytag MDB 4000 AWB. Not cleaning. not getting water now. pressure was low when i was getting water. . Soap dispenser would not open as well. I replaced the motor on the soap door. cleaned the float switch. Tested continuity and cleaned out water inlet valve. Still not getting any water


... Maytag Dishwashers

Maytag, Quiet Partner II. Top water wheel is not getting does not get sufficient water pressure. Without sufficiant water proessure the water wheel won't spin, without the spinning effect dishes on top rack do not get clean.


Motor-Pump Drive assembly is defective.Hey while you have this machine apart pull the drain pump off and look for a jammed flap,it's rare but check it anyway.(to remove the drain pump just twist it and pull it off).For the non believer's out there ,t ... Dishwashers

No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks


SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

Water is getting into the unit but the arms aren't spinning. We can drain away the water but water doesn't seem to be getting any pressure to get up to the spinning arms


... Bosch 24 in. SHV55M03GB Built-In Dishwasher

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

I have a kitchen aid dishwasher. The upper spray arm is getting water and getting enough water pressure but wont seem to spin. Ive ran a lot of tests but nothing. ive cleaned out the spray arm and port that gets water to the spray arm. Cant seem to fix it. Any ideas?


Hi,When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher Spray Arms not Spinning ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Maytag MDB9150AWW model not getting wash water, gets rinse water


Hi,\015\012I think you have thought this through throughly and have narrowed it down pretty good....\015\012The soleniod valve does work or you would not be getting rinse water...\015\012The float is working or the rinse would eithe ... Maytag 24 in. MDB9150A Built-in Dishwasher

Fisher and Paykel Dishwasher, bottom drawer gets water in it. This drawer is seldom used and when used the water empties completely. However, it always has water standing in it. I run the rinse cycle and it gets all the water out but after time the water is back. It is enough to cover the large removable metal cover.


... Fisher and Paykel Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

How can I shut off the water supply to the dishwasher? It fills slowly with water from the top (while not running), and then water spills out over the kitchen floor. By pressing the 'Drain' button, the water will drain out, but I have to get to it before it floods. It takes about 4 hours for it to get to the overflow stage. It is a Jennair model, about 9 years old. We have a lot of limescale, it is probably time to replace it, but for the moment my main concern is to stop the leak. Thank you for


Most water supply lines are attached to the hot water supply under the kitchen sink. If not it may be accessible from the basement somewhere under where the dishwasher is located. Regarding the issue with the dishwasher, the inlet water v ... Sears 24 in. 14181 Built-in Dishwasher

My Kenmore Elite dishwasher doesn't wash dishes properly. I think that it is not getting enough water in the machine. It only allows about an inch of water to get into machine and then starts. I do not think that there is enough water to spin wash arms. I have 40 PSI coming into the house. I am on well water and found debris in the intake orfice. I did my best to flush. Could it still be bad?


I am having the same problem with my brand new Dishwasher. ... Kenmore Dishwashers

It seems that not enough water gets into the tub. There is no kink in the water line. If you manually add water it drains out before resuming wash cycle. The water doesn't get around to wash the dishes let alone rinse the soap off the door!


If the machine has stopped half way through due to switching off or power intruption this could happen.\015\012\015\012So allow the machine to complete the cycle. \015\012Do no worry running it empty.\015\012\015\012It s ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Model # gsd3320c04bb. I am getting water to the inlet valve. I tried changing the inlet valve but still no water goes thru it. I am getting 22 V AC at the connector when operating. The only water that is circulating in the dishwasher is the water that is remaining in the pump system. Any ideas as to what is preventing the inlet valve from operating?


Sounds like you need to replace the mixing valve which is where your incoming water lines connect to the back of the washer. ... GE 24 in. GSD3320 Built-in Dishwasher

Does not get my dishes clean, leaving a film on my glasses, not getting food off. tried to take apart to clean but could not figure out how to get bottom filter out with the large water bracket going up the back of the dishwasher to the top water bar. I bought as a store model, no instruction booklet. How do I clean out bottom filter?


The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America


Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher

My dishwasher (Kenmore Elite 665) doesn't use up all the detergent in the detergent cup - it always leaves a little behind at the end of the cycle. the dishes don't get quite as clean any more, either. I recently replaced my old water heater - we were getting lots of little plastic pieces in our faucet screens. I'm guessing that the water pressure may be low, and that it may be due to the same problem. Is there a screen-type filter that filters the incoming water, before it enters th


I don't believe you have a screen at any water feed and doubt that would be the problem. Once the washer fills the pressure to the cleaning arms is provided by the pump itself. I have this issue every couple of months due to hard water and the calci ... Dishwashers

AEG 50740 Like Mik, my water isn't getting heated. I have almost got it naked but can't get the front clips to come off so can't get right inside. If it is a water heater issue then I will replace it but I don't know if a new ecu would be practicable. Martin


Some machiens front bottom plastic is a "bump" off type (push sideways clip) Some machiens have electrical elements but some (later models) have inductive heater that fit in line with thewater pipe feeding to the main top washer arm. The electrical c ... AEG 24 in. Favorit 40850 Free-standing Dishwasher

Hi, I have a 3 year old Nemo F&P dishwasher which turns itself on and off for about 3 seconds each on/off continually.Eventually it does get enough water to wash but never goes into the wash cycle properly, ie the water just sits at the bottom. We dont think it's water pressure and it was working fine until recently.Could it be an electrical problem with the signal to fill properly not getting through? Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1211 seconds