Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

Will not start , all lights will come on but will not start when i push button. I have done the series of pushing scrub/dry and it will run through the series of cycles.


Answers :

Check the motor start capacitor on the side of the motor,it may be bad and w/o it the motor wont start or run
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will not start , all lights will come on but will not start when i push button. I have done the series of pushing scrub/dry and it will run through the series of cycles.


Check the motor start capacitor on the side of the motor,it may be bad and w/o it the motor wont start or run ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

I have a Maytag dishwasher quiet series 300. It is one year old. The problem I am having is this. After running a cleaning cycle, there is water in the bottom of the machine. If I push the start button, then cancel a few seconds later it will drain. Any idea? Thanks, Terry Roose


Hi Terry, Welcome to FixYa, I am Kelly. \015\012 A few things can cause this. Most of the time it is drain related with the Air-Gap being the culprit that is restricting drain flow. If the dishwasher drain has a restriction ... Maytag Dishwashers

When i push the normal wash then the start button- the dishwasher turns off, when I push the start button, it runs the 2 minute drain cycle.


... Kenmore 24 in. Elite Built-In Dishwasher w/ Ultra Wash Filtration

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

I have a Frigidaire Dishwasher model #FGBD2431KBO. The problem is when I push the start button it fills with water and then will not start wash cycle. If you push the start button again to stop and again to start then the washer will empty the water. So it seems that the motor runs only in one direction.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

When starting my GE Dishwasher I made a mistake & pushed the start button twice, now the cycles are all out of sync, what should I do to start it? It will run but sounds like there is no water in it. I pushed the reset button,but turned it off, because I was afraid I would burn it up, with no water coming in.


Push and hold the reset button for about 15 seconds should be ok,if not do same with start botton.adrian,,,,, ... GE Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Dishwasher model KUDK01TKWH0 will not start the wash cycle. The Cancel/drain button causes the motor to run and the pump to move water. Pushing the start cycle button has no effect.


... KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher

The top drawer in the wash cycle after starting will only run three to four minutes and it drops into pause. have to go and push the start button again for the cycle to continue a few more minutes before it drops out. and I have to do the procedure again. The cycle continues where it left off. I had an issue with a missing rubber gasket initially. The service person came out and removed the front, and this is when the problem started. It might be a coincidence. The repair person does not wish to


\015\012\015\012\015\012\015\012If the cycle doesn't complete, or pauses again n again in between then check these:\015\012\015\012\015\012Water-heating cycle\015\012\015\012Many dishwashers heat the wash and/or ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Have kitchenaid dishwasher kuds30fxss3. When pushing start button, start button starts flashing and beeping. If I reset breaker in basement, it will run one cycle and then start flashing the next time. Any solutions?


... Dishwashers

Our dishwasher (a Maytag - MDBH970AW) will not proceed past the intital intake of water. It has done this occasionally in the past, but with repeated attempts to start a wash cycle, it would eventually work and continue to work for some time afterward. However, in the past week, it will not go through a wash cycle. I have ran the water, prior to starting, to ensure that it is intaking very hot water. When it quits, I can push the start button again and it will go through the 2 minute drain c


... Maytag 24 in. MDBH970AW Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I have a Maytag Quiet Series 300 dishwasher model number MDBH955AWW. When I press the wash cycle button it starts and then automatically jumps to the rinse cycle. After going thru the rinse cycle for a couple of minutes, it shuts off. After that,I can push the wash cycle agin and it works. Any idea what could be wrong?


HI. This will be a basic logic chip fault. It could possibly be solved by simply preforming a hard reset. You can do this by shutting down the power to the unit for five minutes. This shutdown will force the logic sector of your electronic control bo ... Maytag 24 in. MDB9750AW Dishwasher

We have a Frigidaire Gallery Series dishwasher we just purchased in August. Model #GLD2445RFB2. We are experiencing a problem with it. We noticed it started running louder then normal and now it will not finish a wash cycle. It gets half way through and PF lights up on the display and the cycle never finishes. It doesn't matter which cycle we choose it has done it on all of them.


... Frigidaire Dishwashers

I have a maytag quiet series 300. When it is done with any of the cycles in leaves about 1-2 inches of water in the bottom of the dishwasher. I can manually hit the start button twice and it will go through a 2 minute cycle and pump out the water. I have cleaned the filter inside the dishwasher where it drains and have checked the hose to the disposal and it pumps out fine. It just doen't pump itself at the end of the cycle. HELP!


Here it is - Maytag Quiet Series 300 Manual ... Maytag Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a frigidaire fdb1050reb2, when i push the start button it sounds like water is running in it but it never runs thur cycle


... Frigidaire Dishwashers

We can't find our owner's manual. We bought a Siemens dishwasher in 2003. We just interrupted the drying cycle and now the dishwasher won't close all the way and the LED display is off, but if we push the on/off button, it starts a new wash cycle. We don't want to let it run because we're afraid of flooding. Advice?


Close the water inlet tap ****. Give a try and finish the entire cycle. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1232 seconds