Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

We can't get it to cycle.... the green light next to 'clean' is flashing on the panel - can't get it to stop flashing and run??


Answers :

Found it; High temp scrub--Energy saver dry---High temp scrub---Energy saver dry--press start, close door ,wait for it to reset,open door press cancel and you are ready to go.
Hi
\015\012
\015\012Please check if the clean light is blinking 7 times. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry.
\015\012
\015\012If this doesn’t work then its an issue with the heater circuit, door switch, wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. If heater is fine then make sure water pressure is optimum and fill valve is working fine.
\015\012
\015\012Please post back for further assistance.
\015\012
\015\012Daniel
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We can't get it to cycle.... the green light next to 'clean' is flashing on the panel - can't get it to stop flashing and run??


Found it; High temp scrub--Energy saver dry---High temp scrub---Energy saver dry--press start, close door ,wait for it to reset,open door press cancel and you are ready to go. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

The green light flashes consistently after stopping. I have noticed during the cycle that-: The rinse/wash/dry/end lights flicker, occasionally the wash cycle will run for 2 hrs before completing or malfunctioning, will sometimes make a unusual noise (growning)and then malfunction, and will try and click the soap dispenser door a number of times and then malfunction. All the above symptoms will happen intermittently and have been progressively getting worse and are now at a point where the dish


HiThanks for using FixYa. If the green/clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean lig ... Dishwashers

Kudm01fkss0 not running, initially the green light next to rinse flashes in the middle of the cycle. I clicked on cancel to drain. I ran the test cycle and the light next to normal was lit when done but it still will not run a cycle.


... KitchenAid Dishwashers

Kitchenaid kudc03fvss0 dishwasher stopped mid cycle without drying dishes last week and then stopped altogether with lights flashing and full basin. I disassembled filter/pump cover in bottom and cleared several plastic pieces and cleaned chopping blade and screen. After unplugging/plugging and pressing cancel button the pump runs for about 10 seconds and stops with normal and heavy duty lights flashing. What should I check next?


... Dishwashers

I have a Whirlpool ADF951, it has power to it and was working fine, the power light is on and the green light to the far right of the cycle lights is flashing, I can only get any response if I hold the start button in for about 10-15 seconds, The machine stops the light flashing and makes the noise like it is starting , that goes for about 20 secs then returns to the flashing light stage, any idea's please


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water tempera ... Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Built in model MDB5601AWB- about 3 years old. The touch panel stopped working..no lights would come on when touched. Tried it a couple of days later. Lights came on..finished a cycle. after satying in the wash mode for a few hours. Then lights started flashing on and off. At that point I shut it off at fuse box since I couldn't get lights to stop blinking and haven't trusted to use since


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. From what you have described it seems to be the ... Maytag Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

After unit runs for a minute it stops ,open door and all lights are flashing.took bottom panel off and light forwash pump on,green but not flashing, took screen off didn't see anything.


It is possible the wash pump is faulty and is preventing the water from circulating leading to error condition.\015\012\015\012Refer ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Kenmore dishwasher model number 655 16022400 has a flashing green clean light. Reset panel and now the washer will not complete a wash cycle. The washer stops at the drying part of the cycle. What is the problem?


... Kenmore Dishwashers

I have a Fisher&Paykal DD6031 drawer dishwasher. Stopped running mid cycle. Lights flashing on drawer front green,red,yellow,red green,red,yellow . I don't know what that code means. On the inside Heavy ,fast,rinse were all lit Red. It sings "the star spangle banner" too!


Follow this steps and fix it. GOD BLESS YOU\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have a Kenwood Slimline Dishwasher KS474s for a year and it has always worked near perfectly. rn However, over the last couple of weeks the dishwasher has not been running the cycles properly (stopping half way through etc, starting the the delay timer half way through cycle), but it always sorted itself after being turned off and starting again. The trouble is now it has got worse.. when I turn it on the panel and lights on the front just flash, the delay sometimes scrolls through on it'


... Kenwood Dishwashers

My smeg dishwasher seems to be permanently in wash mode. The light on the menu of settings no longer flashes, but permanently is on, and when I run a load it never stops. I hear the two beeps as if the dishwasher is starting a load so it seems to be cycling through over and over. How can I fix this and get the blinking light back? Thanks


You have a timer relay issue ,probable need a new board for it ,a cheap fix would be to time it and see how long it take to run full cycle and put a regulaer outlet timer on it or a alarm off your stove or what ever,save a couple of bucks ... Smeg STX2 Dishwashers

Dishwasher Whirlpool ADG7540. Does not complete cycle. Approx 20 minutes into cycle dishwasher appears to get stuck on rinse.The water is cold. Machine stops and makes a constant beeping noise and the green light flashes 3 times repeatedly.


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

We have an Asco type DW 95.5 built-in, model 1885. During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric still runs. When I pop the circuit breaker, all is stopped. However, when power is restored, the lights and code flash as above, and, again, something electric runs. My email: [email protected] Thanks for any help...


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description " During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric s ... Asko Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Zanussi DE6744 dishwasher won't run it's cycle since I ran a dishwasher cleaner through it. It powers up then stops and flashes 2 green lights alongside a symbol that looks like a bowl with steam rising from it and an arrow with an upright line to it's right. There is also some standing water in the base of the machine. What do these mean.


The first thing I would do is check the float to be sure it is not stuck in the over filled position. Then I would check the drain to be sure that there is nothing clogged in the drain line. Then I would check to make sure the fill valve is working a ... Zanussi 24 in. DE6744 Free-Standing Dishwasher

The normal cycle and cancel green light are flashing but dishwasher will not run. I cannot get any buttons to work, the resume does not do anything. I tried killing power from the circut breaker but same problem when power came back on. any ideas?


Best Answer - Chosen by Voters\015\012First, press and hold down Cancel and see what happens. That may reset the cycle.I did however find this online for the normal light flashing:The reset sequence used was ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Model #DU1050xtpb3. I can' get it to wash. It stopped in middle of cycle. The green light on the clean button flashes 7 times then skips about 20 then starts blinking 7 times again.


Hi,This machine was made by Whirlpool and the flashing clean light is a common error code for them. If\015\012the clean light is the one flashing then your dishawasher could have a\015\012heater circuit problem (depending on t ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2266 seconds