Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Answers :

Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that works then replace the latch assembly. It is also possible the membrane switch got rattled with the door falling, or a wire is grounding out somewhere.\015\012Hopefully it is just the latch. Hope this helps, good luck.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Frigidaire dishwasher does not start. but i see the cycle select LED light come on . all of a sudden the dishwasher stopped working. all buttons except the "start" work. i can select 'normal', 'pots n pans', select the delay etc, but the START button will simply not work!


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

Hello, my Siemens integrated dishwasher no: SE64M359GB stopped working mid-cycle with 35mins remaining. It is displaying the red tap emblem. Usually the dishwasher starts when the dishwasher door is closed fully (having pressed the power button). However, it is making a noise as soon as the power button is pressed. I have checked the water supply and pipes and they are OK. The filters are also clean and OK. We have an electric de-scaler on our system so I imagine calcium build up should n


... Siemens Dishwashers

My maytag dishwasher model mdbh979aws does not start, the lights on the panel are on but the start button will not activate the system


... Maytag Dishwashers

Dishwasher flooding Hi my Asko D1716 Super Cleaning System Dishwasher has started to have a flooding problem. When the cycle finished last night it seemed fine then in the morning the machine was full of water, I scooped out the water and by this evening the machine had flooded onto the kitchen floor. I tried other solutions I found on this website but they didn't suit my dishwasher as it doesn't have the appropriate buttons. Any suggestions would be appreciated!


When you say that you tried other solutions.. it's hard to know which you've tried and which you haven't so I will suggest some basics first.. ( if you've tried them, then disregard)...\015\012Have you checked or addressed the following:\ ... Asko D1716 Built-in Dishwasher

My Maytag MDB7609awb2 dishwasher has a glitch When I try to turn it on the heavy and light was lights go on but won't start the normal wash light won't go on at all until I keep pushing the off and on for a while, then suddenly the normal button works and start will start the machine, then is washes without any problem.


... Maytag 24 in. MDBH955AW Built-in Dishwasher

I have a Kleenmaid dishwasher model DW20W and it all of a sudden won't start. The door shuts ok, the power is on and the start light is on. The salt light is also on so we replaced the salt but that didn't help. The cycle seems is stuck on the universal 65 degrees mode and I cant move it forward or backward from that mode. Ive switched it on and off and pressed all the buttons. It won't start. Help?


... Dishwashers

The dishwasher has the normal and economy wash lights flashing and after we hold the start button down for 4 seconds the stop and then return to flashing? The washer motor runs when the door is closed and no water comes out and the system doens't stop trunning until the door is opened. The system ran for over 4 hours yesterday. Viking Professional


Hello, welcome to ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

I have a Whirlpool dishwasher about 4 years old and it is all of a sudden very difficult to activate the start button. If I lean into the door and push up a bit it may or may not start. What is the problem and can I fix it myself?


Hi\015\012\015\012The issue is with the control panel/key pad that is bad and\015\012should be replaced. Hope this helps...please post back for further assistance.\015\012\015\012Daniel ... Dishwashers

Is it possible to reset a Maytag QuietSeries 300 undercounter dishwasher? Suddenly, only a couple buttons and lights work. (none of which are the START button)


Hi,Have you tried to Disconnect the Power Supply for Few Minutes. This usually Soft Reset the Dishwasher.There is no Reset Button. If problem persists, you need to Replace Touch Pad which is a Common Issue on this Series. ... Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

We have the Whirlpool dishwasher ,Model: ADG6 955. used it smoothly last night but this afternoon, it just will not start up. The green 'START" button keeps flashing and the dishwasher just does not start operation. I tried to reset it by holding onto the start button for a few seconds. The dishwasher stops and nothing more. KIndly advise


... Whirlpool Dishwashers

Whirlpool ADP6000WH No Power up We started a cycle , then all of a Sudden it shut off completely.... No error code at all and no lights or Display. No fuses in the House were thrown and i've tested the power point on the wall and all is ok. Just no response when pressing the Power Button on the Dishwasher??? Please Help :)


... Dishwashers

I cannot get the dishwasher to start. It is the digital one and the staart button does not work. I called Jenn aire and they said to turn off circuit breaker so system could reboot. Some of the other lights come on, but not all of them


If turning off the power to reset the central control board doesn't work u will need to replace the board, the control board and the buttons and indicator lights are all one piece, to replace this part u must remove all the screws that h ... Jenn-Air Dishwashers

I just started a light wash cycle on my Kenmore Ultrawash model 665.1359. The cycle stopped suddenly and now the heated dry button is flashing. I tried pressing it for 10 seconds, but it won't stop. I cannot get the dishwasher to resume its cycle. What do I do??


... Kenmore Dishwashers

When I depress the start button, the timer is clicking to engage and begin the cycle, however, the dishwasher does not start. Other times, there is no noise whatsover when I press the start button and neither does the dishwasher start. If I don't use it for say 2-3 weeks and try again, it starts working for a period of a few months, but then the same thing happens again down the track. This has occurred about 4 times.


Hi.Resetting the breaker means turning power off and back on from the main switch in your house. Same as disconnecting power cord.I am sure that in this case "tripping the breaker" will not help. Repairing appliances is not th ... Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

I have a GE pdw9880 dishwasher with the hidden soft touch pad buttons. All the buttons light up and beep and go through their selections except for the start button. The start button doesn't light up or beep and the dishwasher doesn't run. Do you have any idea what might cause this? Thx


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2083 seconds