Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Answers :

Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending on the error which caused the reason for wanting to reset it, it may be futile and the error will return. Depending on what was done trying to service the unit.\015\012\015\012On the control panel push these buttons in a back and forth sequence within 3-5 seconds. \015\012\015\012With the unit in the "off" status ( no lights on )\015\012\015\012Hi temp scrub - energy save dry ( air dry )\015\012Hi temp scrub - energy save dry \015\012Hi temp scrub - energy save dry\015\012\015\012Close the door if not already closed, all the "leds" should light and it will advance through an abbreviated test cycle. Allow it to complete and you should be good to go.\015\012\015\012There is also an extended service diagnostic which can entered that requires approx. 20 mins. to complete. Let me know how you make out with this one and we`ll move forward if necessary.\015\012\015\012Thanks for choosing FixYa and good luck.\015\012\015\012Regards,\015\012\015\012Macmarkus :)
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishwasher front panel lights are all blinking in unison. Pump has removed all water from bottom including sump. Pump and lights will not shut off or reset with dishwasher door closed or OPEN. I have shut the circuit breaker off to keep from burning up the pump. Problem continues if I reset circuit breaker.


It would help to know what the make and model of the dishwasher is.\015\012\015\012Most likely the flood switch at the base has been activated. ... Dishwashers

No power unit went dead checked power to base of unit ok also shut off breaker for 10 minutes to see if it will reset, no luck. Also removed inner door panel to reveal circut board to look for a reset or small fuse, none evident.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher

The dishwasher ligh blinks showing that its clean. when i go to load it and start it it wont reset, it blinks as if its clean. how do i reset it. ive turned the breaker off and nothing works.


... GE 24 in. GLD5500L Built-in Dishwasher

ASKO 1555 dishwasher won't run. The anti flood device motor won't stop running but we've removed all the water. All the lights on the front panel blink in unison and when we hold down the start/cancel button on the front, nothing resets. We can't run our dishwasher. We've tried disconnecting power and resetting the circuit breaker but the churning motor won't stop.


Hello,Welcome to FixYa.Based on your description " The anti flood device motor won\\'t stop running but we\\'ve removed all the water " It is likely nothing very serious. ... Asko 24 in. 1805 Built-in Dishwasher

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

I have a Samsung DMR78AHS. I recently had a HE1 error code, which is a heating error code. I followed the manual's troubleshooting steps - I reset the breaker as well as removed the dishes and ran it empty with soap. Now when I run it you can hear it fill and empty, but it does not wash anything... no water is sprayed. Is there anything that can be done to reset this or is it a totally different problem.


... Samsung DMR77LHS Tall Tub Dishwasher

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

Unit went dead. There is no power (electric) to it. I checked the circuit breaker and even changed the breaker, but no power. Removed the bottom foot panel and did not see any reset button. I don't know what else to look for.


The electronic control board has failed & needs to be replaced,by someone who knows what there doing.GOOD LUCKECO KIZZA ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

BOSCH SMS50E02GB SHOWS ERROR 15 BUT SOMETIMES DOES NON SHOW ERROR, WAS TOLD BY THE BOSCH HELPLINE TO REMOVE PLASTIC COVER IN THE FILTER AND CHECK THE IMPELLOR FOR DEBRIS NOTHING FOUND, RESET AS PER INSTRUCTION BY PRESSING START BOTTON FOR 3+ SECS.TRIED AGAIN STILL SHOWS FAULT THE MACHINE IS ONLY 6WEEKS OLD. NORMAN


... Bosch Dishwashers

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

Dishwasher trips breaker. Breaker only resets of door is opened


Wires rubbing inside dish washer , surprising its not blowing fuse in dish washer plug . ... Dishwashers

Hi! My Bosch began by tripping the breaker during the cycle (several times if I could get it to reset) and now will not start at all. Even when the dishwasher is off I cannot reset the breaker unless I kind of move the machine around a bit. Sometimes it pops the breaker just closing the door...


HelloWelcome to Fixya.Based on your post,"...Even when the dishwasher is off I cannot reset the breaker unless I kind of move the machine ... Bosch SHU9915UC Dishwasher

3 sec light on control panel blinks .. dishwasher wont star. None of the other control lights come on. I have reset the breaker in the main panel to attempt to reset any internal breakers with no results. When I attempt to set anuy of the options, the 3sec light blinks then returns to a solid light.


Go to maytag website they have all kinds of help there ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My Bosch SHE45M built-in dishwasher is suddenly taking an extra-long time to go through its cycles. On Regular wash it will countdown from 117 minutes to 31 minutes. When it hits that time it resets to 87 minutes, then counts down to 1 minute and will not stop. I have to hit the cancel-reset buttons for it to drain. I have tried to do a hard reset by cutting the power at the breaker for 20 minutes or more. I'm interested in potential parts and a description of how to fit it! Thanks in advance.


... Bosch SHE45M06UC Built-in Dishwasher

The dishwasher starts and initially rinses the dishes without heated water. In the next part of the cycle, the water is supposed to heat to a certain temperature.Beginning this morning, in this second part of the cycle,the dishwasher trips the circuit breaker. If you reset the breaker and turn the sihwasher back on, the breaker trips again. What is wrong and how do I fix it?


Hi\015\012\015\012The issue is with the heating element of your dishwasher, it is withdrawing very large amount of power and thus, the circuit gets overloaded and circuit breaker trips. You'll need to check for any short circuits around t ... Dishwashers

I need to know how to reset the "brain" the start button is flashing and won't stop when I close the door it makes a humming noise and no water is running. I turned off the breaker but it won't reset. Is there like a "hard reset" I can do


I don't think you may need to reset the dishwasher. All that might be happening is the float switch located in the base may be malfunctioning. It could be stuck. Try pushing it down and see if it lifts up by itself. It should only lift when water is ... GE Adora GHDA656LSS Stainless Steel Built-in Dishwasher

Model KUDE70FXPA after use will not start next time unless I go & reset the breaker. Locals have replace breaker. once i turn off at breaker cycle will run.


... KitchenAid KUDE70FXPA EQ Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a GE QuietPower2 (Model GLD5800L00BB) and the lights are blinking and there is a beep about once every 60-90 seconds or so. I have reset the circuit breaker but when I turn it back on, same issue. I can't reset or turn on.


This model has a known problem with the door switches. There are two switches and they both need to work right, otherwise the panel switches will not work right. Turn off power before working on the switches. They both have to open circuit when the d ... General Electric Adora GHDA670N Built-in Dishwasher

We had an electrical surge that knock out some of my appliances. I went to the electrical box and reset all the circuit breakers. Everything worked again except my kenmore dishwasher model 22-16533. I am told there is a combination of buttons you push to reset the dishwasher, but I don't know the code. help!


Hi pedelz,First please check if your dishwasher is receiving power from the outlet.You can reset the control by pressing these buttons in this order\015\012fairly quickly: HEATED DRY - NORMAL WASH - HEATED DRY - NO ... Dishwashers

GE Triton XL dishwasher makes high-pitched noise after a power outage and no buttons work. I reset the breaker and pressed the reset tab in top of the door.


... Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

Model No KFID 60A Dishwasher I have tried to reset but only spraying .I have followed instructions to reset. Press start button for 2 seconds until light goes out. Leave to drain then start a new programme. Still only spraying.


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0990 seconds