Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

With Kitchaid dishwasher KUDS01FL, it wont run. All control buttons seem to work (by lighting up when pressed) except "start". When press "start", it doesn't blink or start. Does this indicate a bad start button switch or something else? Is this something I can replace? Thanks.


Answers :

Hi

Thanks for using FixYa.
To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...

-high temp wash

-heated dry
-high temp wash
-heated dry

If still the issue is not resolved then you'll have to replace the start switch, if you have some expertise then it can done by you. However, before replacing it you can also take it apart and blow some air with the help of hair dryer so that if there is any moisture it blows it off. Please accept the solution if the issue is resolved or post a comment for further assistance.

Thanks

Rylee
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

With Kitchaid dishwasher KUDS01FL, it wont run. All control buttons seem to work (by lighting up when pressed) except "start". When press "start", it doesn't blink or start. Does this indicate a bad start button switch or something else? Is this something I can replace? Thanks.


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

I have a Kitchen Aid KUDKO1ILBS1 which is constantly blinking clean. I have replaced the circuit board once because the capacitors were bulging blown out. After replacing the board the dishwasher has a mind of its own and will start when it feels like it. Now it will not start at all. Buttons do light up when pushed but it always retruns to blinking clean. Got a solution?


Hi\015\012 \015\012If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean ligh ... KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher

Clean light blinks 7 times pauses 1 second and repeats. will not work. the light above the clean cycle indicator blinks 7 times. I can not run the dishwasher, When I press start the light above the start button blinks and will not start


Hi there,\012Well first of all you reset this by pressing - High Temp Wash, Heated Dry, High Temp Wash, Heated Dry, High Temp Wash.If you don't have a heated dry then use "air dry"This sequence help you to reseting the e ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

I have a Quiet Partner II dishwasher. The clean button is blinking with a green light. When I try to start is over, nothing happens. When I push the cancel/drain button, I hear something happening for maybe a minute, then it reverts back to the clean button blinking and won't take any other commands. What should I try next?


... Kenmore 24 in. 16222 Built-in Dishwasher

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain button still nothing happened. I close the door tight..nothing. I check the trays if there something stuck inside..nothing. I unplug/replug the power cord nothing? my wife was using it when this got stuck about 3 weeks ago.


Did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Whirlpool dwh b10.yesterday had problem with water not going anywhere,had to bail it out.today cleaned all filters,now can hear pump working but doesnt appear to be taking water in.i press start button for two seconds,re-programme,and it does the above.then start button flashes and there is a continual beep the programme indicator changes from a wash to rinse during this process.any help ? thanks pete.


... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

Dishwasher will not start when pressing the start button. Timer light flashed numbers and went off. None of the lights and buttons work. Circuit breaker in electrical panel is working. Does the on/off switch need replacing, or is it possible a mini circuit board is bad? Dishwasher installed in 2000 and is used on the average once per week.


As it is nearly 10 years old i would suggest you replacing the circuit board. To test exactly we would need the help of an continuity tester and multimeter. ... Bosch 24 in. SHU53 Built-in Dishwasher

Normal cycle indicator is blinking, pushed the resume button and the cancel indicator begins to blink also, and dishwasher wil not start?


... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Frigidaire Dishwasher gld2440reb1. After removing filters, cleaning and replacing them I had three flashing lights ie Sensing, Clean and Sanitized. all buttons were inoperable. after unplugging and reconnecting I had a PF or power failure indicator. after pushing the start button the PF went off but no further action from any button. Help!


Usually if you get a PF error that means you have received a power failure usually from the control board shorting out on this model. Typical reasons the control will short out is from either the circulation motor shorting or pump motor shorting. If ... Frigidaire Dishwashers

I press the Normal wash button and Start button. The dishwashed doesn't come on. Cancel light is blinking..I press "cancel" and it sounds like the washer is doing something..not sure what..then after some minutes it stops. Any ideas?


... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

My GU 120 stops mid cycle and the indicator light starts blinking a humming whirring sound preceeds the ctcle stop nad light blinking. Pressing the button for 5 seconds causes the flashing light to extinguish but the sound continues untill the unit stops. It does not complete the full cycle. Your help would be appreciated. Tony


... Whirlpool Dishwashers

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

I have the above dishwasher shv57c03uc just less than 5 years old. The door latch does not engage solidly. when i pust start button left side lights on indicator right does not come on and i have to push on button twice for washer to come on. When it does come on the cycle is real short and it does not complete a full cycle. I an asuming the circuit board is defective!! does this sound right? if so how can i replace the board?where can i get troubleshoooting instructions?


Hi\015\012\015\012You are right it is the ... Bosch 24 in. SHV57C03UC Built-in Dishwasher

Kenmore Ultra Wash Dishwasher (Mod: 665.1373) makes bad noise after the tub fils and the pump starts running. (Not sure how to describe noise.) Bad pump? Other? I have checked for anything obstructing rotating parts and that is definitely not it. My guess is something wrong with the pump, but not sure. If so, I'm wondering what my options are. Like are their common problems with pumps that can be fixed at home? Replacement?


Definately sounds like a pump on its way out. Probably not the pump itself - but the starting capacitor.However it may be cheaper for you in the long run to have a professional out to diagnose the problem instead of throwing money into it blind ... Dishwashers

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

I got a GLD4400N00WW dishwasher, The normal and headed dry lights blink. I already replaced the touch pad. Once your reset the d/w and shut the door the lights will come on and you can start the cycle. Once you press the cancel button the lights blink and thats it....


... GE Profile PDW8400J Built-in Dishwasher

I push the wash button and the washing light blinks but the dishwasher doesnt start ?


Possible causes are the door switch or mainboard ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I just replaced the heating element and it was working fine for about a week. Yesterday, the soak and scour light (which I've never even used) started blinking constantly. The dishwasher, Model GU2400XTPB3, won't let me even enter the reset code. I need to know if it's something we can fix without paying for another part/service by finding a manual. Thank you.


... Whirlpool Dishwashers

DU1055XTPQ3 built in Dishwasher... panel has power "cancel" button when pushed you can hear the pump running but on wash the light blinks about 3 times and goes out, nothing happens. Is there a sensor or something in the panel that needs replaced? Jim


Hi\015\012\015\012First try resetting the dishwasher by pressing the AIR DRY button and hold it for 15 seconds. After this if it blinks again 3 times then the control needs replacement. Hope this helps...please post back for further assistance. ... Whirlpool Dishwashers

"Normal Wash" Light blinks intermittently. Washer will not start. I can hit the "Cancel/Drain button and the washer will drain. I have replaced the main circuit board and still have the same problem. What's my next step


What model dishwasher is it? ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1114 seconds