Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

My dishwasher will fill with water but when it goes into the wash cycle it makes a noise that is like a grinding or loud hum and it will not go into the wash cycle but it will pump the water out of the dishwasher when you cancel the cycle


Answers :

Take apart the spray arm assembly at the bottom on the inside. When you get all the way to the bottom and access the spray motor, simply turn the impeller a few times. Put back together and try it now
Sounds like debris in the pump housing . Must remove screen and covers and clean.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

My dishwasher will fill with water but when it goes into the wash cycle it makes a noise that is like a grinding or loud hum and it will not go into the wash cycle but it will pump the water out of the dishwasher when you cancel the cycle


Take apart the spray arm assembly at the bottom on the inside. When you get all the way to the bottom and access the spray motor, simply turn the impeller a few times. Put back together and try it now ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

GE Profile Dishwasher Mod No GSD4930Z02WW does not drain after the wash cycle. Cancel cycle removes a small quantity of water. The filter and strainer are clear. Water flow to the disposal sounds slow. Will I have to slide it out to access bottom pump area?


Hi,If you are hearing a slow flow coming to the disposal that is an indication that the dishwasher is working and the problem is in the drain system between the dishwasher and the disposer. This is caused by a blockage or clog in the drai ... GE 24 in. GSD4930Z Built-in Dishwasher

Frigidare dishwasher model gld355rfb2 when you select a wash cycle unit begins prewash when it moves to wash unit quits and pf (power failure )is on display unit is full of water on bottom of unit so I reset the unit hit cancel button at which time unit pumps off water . I then tried again with same results as above.


... General Electric GDWT160RSS 24 in Builtin Dishwasher

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Dishwasher fills and makes some sound but no water is sprayed. When canceled the pump drains the dish washer. Is there a separate pump that pumps during the wash cycle?


It could be that the jet holes in the rotor arms are blocked.\012\012The arms are easy to remove so take them out and check out the jets.\012\012Also take out the filter in the bottom of the machine and check that it is clear. ... Whirlpool 24 in. DU920QWD Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My Kenmore dishwasher model number 665-16389300 is starting to fill up and not drain during the normal wash cycle. Water will run out on the floor. When we hit cancel and drain it appears to drain just fine so I dont know if it is a pump issue or something in the cycle. What do you think?


... Kenmore Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

My dishwasher siemens se25a266gb purchased in 2003 will fill with water go through a wash cycle but does not pump out the water i have cleaned out the filters, checked the exit hose and all seems ok the only way to get the water out is bale out by hand. after this it will run through a wash cycle then stop and not pump out. how would i get to the pump and check it? any help appreicated regards Alan


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

I have a Siemens Avantgarde dishwasher. It fills with water, the water doesn't heat, it doesn't start the wash cycle. It continues to work through the wash cycle and doesn't pump out or refill with water during the cycle. It pumps out right at the end.


... Siemens Dishwashers

ASKO 1885 Built-in Dishwasher: The water sump fills normally, but the wash cycle does not start. Althought the timer seems to work, the wash cycle motor won't start up in any wash or rinse selection. The spray arms do not spin - no water is being pumped. At the end of the wash cycle time, the water will empty out of the sump. Thank you. TB


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1885 and 2) filling ... Asko 24 in. 1885 Built-in Dishwasher

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

Dishwasher pumps dry, adds and heats water, but does not go through wash cycle. It apparently continues through all cycles, but never pumps the water through the spray arms in either wash or rinse cycles. spray arms are both free and clean, no debris anywhere obvious.


Hi.The impeller pump is probably faulty. Before going for the pump check the drain well and drain hose, drain blockage may prevent the machine from switching to recirculate. Also double check there is no blockage or leak in li ... Asko 1385 Dishwasher

I have a 7 yr old Miele G 641 SC Plus dishwasher, the inlet/drain light comes on and stops the wash cycle.I have tried cleaning the water inlet filter, drain pump and non return valve many times, the wash cycle then starts with the pump out of existing water and can sometimes go for about 20mins( sometimes happens a soon as the water starts to flow in) into a cycle before stoppinig again with inlet/drain light on.


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

Dishwasher fills with water, but spray arms don't spray water or spin. As the cycle moves forward, water is eventaully pumped out (so the pump is working). i've selected different cycles with the knob on the front of the machine but they all work the same.... no swishing with the spray arms. When the cancel button is pushed, the water is pumped out... as it should. Thanks for the help.


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2316 seconds