Having problems with your KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher ?

Stuck in clean cycle....clean light blinking but wont start new cycle


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Stuck in clean cycle....clean light blinking but wont start new cycle


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

The green clean lights blinks constantly, It will not allow me to cancel and when I try to start a new cycle the start light blinks a couple of times then the clean light starts again, but nothing happens.


... Whirlpool 24 in. GU2548XTP Built-in Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


Thank you Daniel Scott. The solution you posted worked for me and saved me calling a technician. My clean light was flashing and I followed your solution to press Heat Dry - Normal twice. And it worked! Thanks so much! ... Frigidaire 24 in. GLD2150RCC Built-in Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


I had the same problem and was told to unplug the dishwasher, wait, and then plug it back in. That didn't work; but I decided to try again. So I unplugged the dishwasher, wiggled the heating element in the bottom, made sure it was in the right positi ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Clean light keeps blinking and I can't start a new cycle


That is a comon problem with that model. It is not sensing a temperature change in the water. Push i believe it is heated dry and sani rinse going back and fourth between the two to clear the code and see if you can get it to complete a c ... Kenmore 24 in. 15932 Built-in Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


Close the door and to cancel that just press hi temp and hetaer dry again hi temp and heater dry and all the lights is gonna light up, it getting into test mode.\015\012After that press cancel \015\012Now get somebody to replace the therm ... Kenmore 24 in. 17032 Built-in Dishwasher

Whirlpool gold, about 2 years old. the "clean" light is flashing. When I hit cancel, a 2 minute dry(?) cycle runs. The clean light resumes blinking. It will not start a new cycle


Looked in the manual and called a repairman ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My dishwasher's clean light will not stop blinking and it will not allow me to start a new cycle. I have canceled the cycle unplugged it and let it sit but the light is still blinking


Your\015\012dishwasher will do this as a safety in case the element is broken and\015\012feeding electrical current into the water. Sometimes just a false\015\012reading.Reset your console by pressing: ... Whirlpool 24 in. DU1055XTPS Stainless Steel Built-in Dishwasher

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

I have a modulogic ADP951.seemed to be stuck on cycle today so I stopped it. water did not drain. I cleaned all rotors and filters and re started. Water drained however start light now flashing. Have tried holding for 5 secconds to re start but only starts pumping out water (of which there is none) and then stops. Light continues to blink. Any other tricks??


I am assuming you have not tried the reset by turning mains power off and then on.\015\012\015\012One of the reasons for being stuck in the wash cycle is the water temperature is not reaching the right level. This could be due to heater ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

It won't start. The clean light is blinking but it won't reset to start a new cleaning cycle. the cancel function work and it will drain the basin but that is all.


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:High temp wash-heated dry-high temp wash-heat ... Dishwashers

Clean light blinks 7 times pauses 1 second and repeats. will not work. the light above the clean cycle indicator blinks 7 times. I can not run the dishwasher, When I press start the light above the start button blinks and will not start


Hi there,\012Well first of all you reset this by pressing - High Temp Wash, Heated Dry, High Temp Wash, Heated Dry, High Temp Wash.If you don't have a heated dry then use "air dry"This sequence help you to reseting the e ... Whirlpool GU2400XTP Built-in Dishwasher

I have a kitchen aid dishwasher that is stuck on the clean cycle. It will drain water, but no water seems to be getting into the washer. If i push the start button, cycle will not start. The clean light is the only light that will stay on. the other lights will go on, but they eventually go off without starting the cycle. Is this the thermal fuse???


... KitchenAid Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a kenmore elite dishwasher, right now it seems to be stuck on the clean cycle the green light blinks on clean,, i pressed start and nothing happens i also press cancelle and nothing happens is there away to reset this or would something be broke


Hi,\015\012\015\012You can also pres "normal wash" and "heated dry" buttons back and forth till all lignts comes on, and it will reset the dishwasher and work normal again..\015\012\015\012But if you get this problem frequent ... Kenmore Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

I have a Kitchenaid dishwasher KUDS01FL. On the control panel there is a clean light that is cycling 3 blinks every few seconds, It won't run. But will drain when you press cancel. But wont start. Any help would be appreciated


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

It has been making a noise when it runs. Cuts off and on. Now the clean light is blinking and the cancel button does nothing. Can't start a new cycle.,


... KitchenAid KUDS01IJ - Multiple Color Dishwasher

Clean light continues to blink and cannot start new cycle


This may or may not help in your situation, but the following link explains how you may be able to clear the blinking clean light problem: ... Kenmore 15892 Built-in Dishwasher

Clean light keeps blinking. Will not start a new cycle. pushing cancel or other buttons does no good.


If this is a Whirlpool manufactured dishwasher (such as the one pictured), the blinking clean light is an interru ... Whirlpool DU1055XTV 24 in Builtin Dishwasher

2 brand new Kenmore elite dishwashers - All hookups checked and correct. Start buttons blink - cycles will not start. 1 washer ran for about 10 seconds - then the light started blinking. Troubleshooting in manual says light will blink if the door is not closed. They seem pretty closed. Dishwashers leveled and plumb. Tried it mounted, and unmounted. No Luck. Thanks


These dishwashers have a safety feature. The door has to be closed within 3 seconds of pushing the start button. If the cycle is interrupted at all by opening the door or pushing something while started you will have to push the start button to resum ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2168 seconds