Having problems with your KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher ?
Kitchenaid - water suppy not feeding
\015 Hello, I have a Kitchenaid KUDI01IL, Dishwasher\015\012It runs through a complete cycle, but it does not appear that the water supply is getting into the machine during the cycle.\015\012When complete the soap power has piles just inside the door, although not completely dry, the pile is not washed away at all.\015\012I dishes have no change from start.\015\012I am trying a Rinse cycle now.\015\012Any thoughts?\015\012Thanks,\015\012John\015\012\015\012 \015\012\015
The water valve is either clogged or burned out. Easiest to check is whether it is burned out. Turn off power, remove kick panel, find where incoming water supply pipe attachs to valve and remove both wires to valve. Zero your ohmmeter and check for continuity across terminals. If it has continuity, valve is good. Use test meter to check for voltage from timer. Connect test meter leads to wires you removed, restore power, close door and put timer, or control panel, to where dishwasher should start filling. If there is 110 volts at the wires to the water valve, the valve is clogged. If there is no voltage, the timer or control is bad and must be replaced.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kitchenaid - water suppy not feeding
The water valve is either clogged or burned out. Easiest to check is whether it is burned out. Turn off power, remove kick panel, find where incoming water supply pipe attachs to valve and remove both wires to valve. Zero your ohmmeter and check for ... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher
Kitchenaid KUDS01IJ lower spray arm wobbles and hits the water feed tube. The parts seem ok. Is there something that is supposed to push the lower washer arm support up?
I have a KitchenAid but model # KUDI24SEWH1. Can not find it on your list although another model without the last letters 'WH1' is on it. Anyway, my nephew ordered the parts he said needed to be replaced. One was the top water feed tube and bearing which he had no problem replacing when the part came in. But, he is having a very difficult time opening up the front door to replace the soap dispenser. Removed the 6 screw (three on each side) and the two at the top of the door but that is as far
You don't Use the WH2 just the first 6 letters and numbers.\015\012Jim ... KitchenAid KUDI24SE Built-in Dishwasher
Will not feed water to unit when turned on? - KitchenAid KUDC02IRB Dishwasher
... KitchenAid KUDC02IRB Dishwasher
NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart
... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher
Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.
If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher
I have a Whirlpool GU2500XTPQ3 dishwasher that is about 5 years old. The dishes in the top basket do not get clean. I checked the water tube that feeds the upper spray arm and the top spray and there aren't any obstructions. Our water pressure and temperature are suitable. Could the pump be plugged or otherwise lose its ability to circulate enough water to adequately feed the upper sprayers? How can I check on that?
Hello,\015\012\015\012Welcome to FixYa,\015\012\015\012Based on your description as well as all you`ve done on your own I`d suspect you`re on the right track with the plugged pump suspicion.\015\012\015\012The plac ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher
Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t
I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer
Kitchenaid (KUDM01TJWH0) Shortly aftter starting my kitchenaid (KUDM01tJWH0) dishwasher, smoke began coming out of the door. I opened the door and smelled a strong electrical smell. It is now completely dead. I drained the water out of the water line, thinking it might be plugged, but still nothing. What should my first move be to determine the cause? Breakers are fine. I think it is was purchased approximately 2001. Thank you!
Wires where thy bend at bottom of door and heating element....water in motor ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher
Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.
Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers
I have a kitchenaid Model KUDW03CTBL2 dishwasher. It is pumping water, but the top sprayer and the one under the top rack just have a little water coming out. Not enough to make them spin. We also noticed the water in the bottom when opened is not as much and it is cool not hot. The dishes on the top rack will not clean, and the bottom is not completely clean. We have checked water pressure and water tempurature through the house, All is operating fine. This dishwasher is only 1 year and 10month
... KitchenAid Dishwashers
KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.
... LG LDF6810 Built-in Dishwasher
Is it common for Kitchenaid dishwashers to have water pooling inside them? It's almost like the valve for water coming in isn't shutting all the way...in the middle of the day, we'll find water inside the dishwasher...it drips out the front when you open the door...but when you turn it on, it doesn't have any problem draining the system...mysteriously, we find water in the bottom...what's up?
There is a rubber flapper valve that keeps water from running back into your dishwasher. It's a $5.00 part, but it's a bear to get to,\015\012\015\012You have to pull the drain pump to access this flapper.\015\012\015\012Also ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher
No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks
SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher
Kitchenaid dishwasher model KUDM01TJB0 Fills with water, heats water but pump dosent run in wash (dosent spray water) Drains water. Every thin appears to work but the pump in the wash mode. I checked the control board and it has no visable issue.
... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher
My 12 yr old KitchenAid -Sculptura-Model KUDR24SE starts to fills with water and then does nothing else. It will eventually go through the cycles on the panel, but nothing is happening inside. End result is still dirty dishes with water sitting in the bottom that has to be baled out. Cups on top rack don't have any water on the indentations, so it's obvious that the thing filled with water and that's it. I had the motor replaced (supposedly with a new) one 2 years ago so I find it hard to bel
The 'check water' light is on. The machine runs but will not fill with water. I have checked the water feed to the solinoid valve. Not sure if valve is opening?
Pour water manually to the wash chamber.If the machine works it is valve problem. Check the other end of the valve for flow.If fitted with rubber hose remove and check.Be careful not spill water inside the machine parts. ... Dishwashers
My KitchenAid Dishwasher wont Spray water. Matter of fact it wont rinse of intruduce any water at all. It Hums. But no water.
SGS43T52GB check water light keeps comming on, yet water feed is ok. Did start once but then ran for 4 hours until I switched it off, full of water
... Bosch Dishwashers
My Frigidaire FDB935RHS0 top rack is not getting enough water (pressure) to rotate the top rack sprayer. We have looked at all the connections under the machine as well as the tubing, but we have not found any obstructions or problems. The water moves very slowly up the tube to the top of the machine and the water only seems to trickle out of the feed line therefore the sprayer doesn't spin or spray. We have disassembled the bottom sprayer and have found no obstructions there either. Do you have
... Frigidaire 24 in. GLD2350RC Energy Star® Built-in Dishwasher
My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!
Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers
Dishwasher i have fixed the fridgadair dishwasher so that i can see what it is doing with the door open; water is coming out of the spinner arms but the arms are not spinning ; it seems that water sprays about 4 inches in air; the top is feed water off and on but not constant.
This dishwasher does not feed water to top and bottom arms at same time. It starts with bottom and then after awhile it switches to top and then cycles. If water comes out arms but arms won't turn, check all holes in arms.&nb ... Frigidaire 24 in. PLD2850 Built-in Dishwasher
Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow
... Maytag 24 in. MDBH955AW Built-in Dishwasher
Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.
It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers
My Kitchenaid ModelKUDI01TJBL0 only leaks at initial start up. Just after the water fills, the first few seconds of the wash cycle. It pours out the front door for a couple seconds than no more for the rest of the wash. It is level, no cracked arms, or loose pumps.Splash guard is in place. The float seems to be working, not too much water in the bottom. I am stumped. Although I do feel that it has something to do with the level of the water being too high, when the arm starts turning, it makes a
Is the unit level or leaning back if leaning back it is morelikey filling too much if level make sure the float moves up/down easy if not clean ... KitchenAid 24 in. KUDS25 Built-in Dishwasher