Having problems with your KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher ?

Our Kitchen Air KUDIo1Ilbl6 DW is 6 years old. The dishes are no longer getting clean. It sounds different in the washer. I question the pressure is high enough inside the unit. I ran vinegar through the unit, did not seem to matter. The temp is 140 the pressure from our well is the smae as when we installed about 55 psi. I checked te screen it seems to be clean. Any thoughts


Answers :

Hi
\015\012
\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's spray arms are working fine and all the holes of the arms are clear. Now try using a different detergent like gel or liquid based detergent to see if it helps.
\015\012
\015\012Dishes are left unclean when the dishwasher is not filling in properly or when the water pressure is low. Check for water pressure and water inlet valve. The water inlet valve if faulty will draw very little or no water. However, if you observe that water pressure is fine and there is no issue with the Fill valve then check whether the dishwasher is draining. If it's not draining then see if the drain hose is plugged or clogged. If drain hose is fine and the dishwasher is still not draining then there is some issue with the drain pump or drain filter. To check this you'll need to disassemble the dishwasher and trace back the drain hose to a pump, remove the drain hose from pump and clean the debris from the pump and filter. Make sure you have lots of towels as there would be a lot of water coming out from the pump.
\015\012
\015\012Next thing to check if the dishwasher is draining and filling properly is water temperature. Water temperature should be between 120 and 140 F. If water is not hot enough then heating element has gone bad, to check the element you'll need a multimeter. Use the multimeter and check if the Rx1 reading on the meter shows reading between 1200 (1.2K) ohms and 1500 (1.5K) ohms, if not the heating element has died. Hope this helps... Please post back for any further assistance.
\015\012
\015\012Daniel
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Kitchen Air KUDIo1Ilbl6 DW is 6 years old. The dishes are no longer getting clean. It sounds different in the washer. I question the pressure is high enough inside the unit. I ran vinegar through the unit, did not seem to matter. The temp is 140 the pressure from our well is the smae as when we installed about 55 psi. I checked te screen it seems to be clean. Any thoughts


Hi\015\012\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's sp ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Unit not cleaning as well as when new;understand that things wear out;is there any kind of filtration system in unit that can be acessed and cleaned to allow bettert water pressures?


Sounds like the heater element not heating as well as it did also you may need to put it through a hot cycle (empty) to flush out any gunk away. ... Crosley 24 in. CDC450 Free-standing Dishwasher

Bosch Diswasher Have Bocsh SMU 2046 UC diswasher. Aprox. 11 years old Has always worked well. Recwntly is not cleaning at 100% as before. Seems to run through cycle as normal and sort of cleans but leaves stains in coffee cups and flatware seems filmy, sometimes a little guk left on dishes, all uncharacteristic of past performance. Tried a thermometer during cycle and water temp is around 151 F during wash, 136 F at rince. and 154 F at dry time. Have checked arms for cloging and are free w


Remove the drain hose and check if you have any residual into it. After 11 years your appliance may need a thourought cleaning.Check also if the pump has enough pressure. ... Dishwashers

Honda gas powered pressure washer--runs great and I get pressure throughout the system but nothing comes out of the wand itself. There seems to be no clog throughout the system . I have cleaned all parts. When the unit isn't started I can get flow throughout the system


... Pressure Washers

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

I have verified power to the Kenmore 15951 unit, but controls appear as if no power. I have tried hitting hi temp, heat dry, high temp, heat dry sequence like my reapir man suggested, to no avail. Not aware of any reset buttons. I have cleaned out the filter as well. Not sure where to go from here.....Rick


... Kenmore Dishwashers

Asko 1375 unit will not wash drains and fills ok  motor at back of unit runs well. Suspect impeller   Does motor have to come off for impeller replacement?? My 1375 is leaking a bit, looks like the seal which was mentioned in the impeller repair case,may be the problem? The other problem I noted was a clogged screen at the bottom of the dishwasher which is on the suction side of the pump, the screen had calcium buildup etc. I cleaned it off with vinigar and reran the dishwasher seemed ot fix th


Do you mean to say that the washer does not go into the wash cycle at all, or washes poorly?An answer to both can be found HERE.This article ... Asko 1375 Dishwasher

I am trying to clean my block paving using my pressure washer Karcher 3.99, which I used successfully last summer, however, it is not cleaning well. I have used the high power nozzle but the power seems inefficient to get the dirt out of the paving. Please can you advvise what you think the problem may be. Many thanks. Sue Thompson


Hello Sue, you don't say where in the world you live, but if you are attempting to clean dirt and algae off pavers, you need to add a solution to the water jet via the inbuilt attachment. Mix a fairly mild solution of bleach and detergent, pus a dash ... Karcher Pressure Washers

I am looking for someone to repair my Karcher high pressure cleaner in or around the Richmond / Hawthorn area. Any ideas? The unit seems to have broken a seal and has lost cleaning pressure and leaks when engaged


... Karcher PSI Electric Pressure Washer

Our dishwasher is only 8 years old and is not cleaning dishes very well. There seems to be a problem with the second detergent door not opening during the cycle. I have cleaned the unit recently and although it needed it badly, the problem has not improved. Any suggestions?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Sears 24 in. 14181 Built-in Dishwasher

I have a FDBB2040FC3 dishwasher and the cycle doesn't complete anymore. I will start the cycle and after awhile the Hi-Temp LED and the No Heat Dry LED will start blinking and the unit stops. The dispenser does release the soap pack and the dishes seem clean but this doesn't seem normal. Thanks for your assistance Todd


Have you checked the element or the heater in you unit when the units senses that the unit is no longer heating the water the unit will stop and not progess any further into your cycle you can check this by doing a continuity test on the element to s ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have an older dishwasher that just no matter what seems to not fully clean my dishes. I rinse and scrub them well but they just still look dirty when the cycle is through. ser/model GSD400W-o1ad mg624080b


... Dishwashers

My kenmore 665.1384 is not cleaning well. There seems to be not enough water coming through as soap remains in the cup after it completes. It is not a new installation, water is hot and pressure is good and it does drain properly,


Found repair video on handyman website ... Kenmore Dishwashers

My detergent is always still stuck in the dispenser. The water temp and pressure are both fine, the machine is clean as well as the spray arms, and the door opens but water just isn't dissolving it. I have tried powder, gel, tablets, and gel packs!!! Please Help!!!


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Magic Chef 24 in. DU2500 Built-in Dishwasher

I have a Maytag MDB8951bws and I have noticed that the dishes at the end of the cycle do not feel hot but mildly warm and not completely dry. I also noticed that when I select the ''Sanitize'' option the light that tells you the dishes have completed being sanitized does not come on after the cycles are completely finished (the ''clean'' light does come on). One last note I will throw in is that the high temp wash seems to work quite well as a lot of steam is expelled when the door is opened dur


... Maytag MDB8951BW Dishwasher

Have a bosch dishwasher model shu3032uc-14 doesn't clean very well it seems top spinner doesn't always turn, had service look at it and couldn.t find problem recommended to use a water softner, other people have same unit and do not use a softner and theirs works great what else should i look for thank you


... Maytag Dishwashers

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

Hi, I have a Karcher K3 pressure washer. 18 months old, used maybe 6 hours total. For the past 3 hours of use the compressor/pump seems to cycle audibly but pressure at outlet hose seems constant, hence I did'nt worry. Now it does not start with switch on. I now hear a buzzing sound from the unit. The unit was last used 6 weeks ago. The unit was stored in the garage away from frost, it does not leak water so I don't think there is any frost damage, but just this buzz. Any suggestions would


... Karcher K3.68MR Electric Pressure Washer

Not cleaning There seems to be a lack of water pressure although the pump seems to work properly. I ahve cleaned the screens. Whem i remove the sprayer arm etc, there seems to plenty of water pressure.


Check spray arm jet holes. Clean the clogging with blower or soft bristles. ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Odd operation Unit turns on, slowly heats up. When wash cycle starts, temp drops 20 degrees. Unit never seems to drain completely. when cycle finishes, Booster heater temp can drop as much as 40 deg (122F) Heater slowly recovers, but unit never seems to go into rinse cycle.


This unit is a sanitizer, not a full fledged dishwasher. It is designed for restaurants and bars where the primary use is washing glassware. The behavior you describe is normal for this model. The manual can be found at the following link: ... Hobart 24 in. LXIH-3 Built-in Dishwasher

The dishwasher isn't cleaning well and doesn't use much rinse agent. I have tried and tried to figure out why the dishwasher isn't washing dishes well and I can't figure it out. I haven't called the manufacturer yet and maybe I should. I've changed the cycles and that doesn't matter. First thing is that it doesn't really use very much rinse agent, so my glasses look yucky. Second thing is that I can tell it hasn't cleaned the dishes well because the inside of the door isn't clean. With a s


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

My Karcher 411A seems to have lost pressure. Behaviour is this, when you press the water release on the spray gun you get 100% pressure for like 10 seconds and then it seems to dwindle down to 30-40% of its total pressure. When the pressure cuts down I can hear more noise coming from the gun sprayer aswell. So not sure if the problem is in the gun or the main pump unit ?


Sounds more like a clog on the intake side. Check the filter and the hose on that side. ... Pressure Washers

Ge Triton dishwasher GSD5500GOOWW was not cleaning like it used to- I cleaned screens at back bottom-very dirty- also-detergent cup stuck opne - took door apart and got it unstuck - it works fine now. - it seemed to do better but now it is cleaning poorly. It seems to fill and start a lot sooner than before - after 30-45 seconds it starts up. I tested the water temp and it is 90 degrees! Hot water coming in is at 105 degrees. Also - it is leaving a white residue on dishes - didn't do that be


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1469 seconds