Having problems with your KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher ?

In between wash cycles, water seems to back up into the dishwasher. I had a plumber take a look at the drain and disposal in the kitchen sink to see if there was an issue there. He suggested to have appliance repair tech to come look and indicated that he believed that the issue may be the "cylianoid" valve. Does the this valve prevent water from backing up into the dishwasher after it has drained?


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

In between wash cycles, water seems to back up into the dishwasher. I had a plumber take a look at the drain and disposal in the kitchen sink to see if there was an issue there. He suggested to have appliance repair tech to come look and indicated that he believed that the issue may be the "cylianoid" valve. Does the this valve prevent water from backing up into the dishwasher after it has drained?


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

Clogged Dishwasher The water won't drain out and I believe my dishwasher is clogged up. Where do I look (I'm assuming at the bottom of the appliance) to find the clog so that I may fix it?


First - if you have air gap on top of your kitchen sink, remove the cap and check if there is a ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Something was stuck in the latch, which made the machine not start. I removed item, however, the lights come on, the heat comes on, bot no water or the rest of the cycle begins...help.. I have held down start/cancel and the heat dry buttons. I have unplugged the power for three minutes... I have taken the front covers off, looked through the latch mechanism but found no other issues. There is a little water left in the basin, so I checked to see if there was a clog, by blowing air into th


Hi,Sorry for the delayed response. Your problem dated 30th Sep 2009 was reposted today on FixYa. I am sure by now some other expert must have responded to your question and solved your problem.If this is not the ca ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

There's a foul smell coming from the dishwasher evert time I open it. Doing a wash does not solve this. I'v had this since it was new, months ago, and have had the installer look at it, said it wasn't his problem. Had a tech. come in and said it wasn't his problem. I've owned many dishwashers and never has it had a foul smell. Last fall I went to Nova Scotia, ran the dishwasher before I left, came back in two weeks and noticied water was still in the bottom of the dishwasher-it didn't drain all


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

Ther's a foul smell coming from the dishwasher evert time I open it. Doing a wash does not solve this. I'v had this since it was new, months ago, and have had the installer look at it, said it wasn't his problem. Had a tech. come in and said it wasn't his problem. I've owned many dishwashers and never has it had a foul smell. Last fall I went to Nova Scotia, ran the dishwasher before I left, came back in two weeks and noticied water was still in the bottom of the dishwasher-it didn't drain all t


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

My dishwasher recently started leaving a white, chalky residue on all the dishes. It wasn't gradual at all. One day everything was fine and all the dishes clean and the next they were covered in nasty residue. We've ruled out any issues with soap, rinse agents and hard water. A appliance repair guy came out and said the float was "tampered" with and said that he fixed it. He said that if the problem came back we need to order a new float assembly kit. My husband has looked at it several times an


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Whirlpool Dishwashers

My fisher paykel dishwasher is filled with water and will not drain. I have looked for damage to ring( none) or any impingements( none). I get a F2 message which I believe indicates a rotary problem.


Hi,no problem with our chat sesson...but your answer is here----if you pull out the lower drawer, there s aside release pin on either side of bottom corner of hte drawers when extended. a small maybe quarter sized hole( no nee ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher

Appliance had been working fine now all of a sudden no water is running in the dishwasher.The machine appears to run through all of its cycles but without water. The water pressure in the ajoining sink appears a little low though the water pressure in the rest of my home is fine. I see no water leakage anywhere. Do I need to call an appliance tech or should I call a plumber? Thank you.


... GE GSD1000 Dishwasher

Water does not come into the dishwasher. can hear the pump, the heater works, the indicator lites illuminate, but water does not come in. The water supply is hooked up and turned on, there is good flow to dishwasher connection, but no water inside the dishwasher during operation.


Hi,\015\012Usually the problem is the soleniod valve that lets the water into the dishwasher...\015\012\015\012here is a tip that I wrote that gives many more details about this problem...\015\012\015\012Dishwasher ... Dishwashers

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

We have a Hobart dish washer in our bar area and when it sits over night there is a pool of water on the floor in the morning. When we open the door and look at the upper right corner in the rear of the machine we have a steady flow of water running down the rear wall. When looking at thge machine where the black 1 inch water hose comes up from the floor there is a plastic T in the line with an electric wire the goes into the side of the T. I am guessing tha that is a sensor valve that is suppos


The model is most likley a lx18,lx30,lx40.The fill solenoid valve is stuck open.Remove the 2 screws on the bottom front where the pressure gauge is.Turn the circuit breaker off.When you remove the cover you will see a bronze valve with a red hose goi ... Hobart Dishwashers

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

Dishlex Global 300 Fills and then stops. faint electrical smell after a while . Checked heating element that I replaced 8 months ago, seems OK. It has 29X? ohms resistance and looks OK. (I am not sure of the reading on my meter but the element is not fused.) Pumps water in and out OK No blockage in pump or filters Water level looks to be low on filling, only part covers the heating element. I tried instruction book on changing water level using the "Eco" button no response as indicated in


You need to open the front cover and check the wiring for any burnt wire,this happen sometimes,if that does not solve then it't either pcb or electric motor causing this smell.You would be better off with a new one then. ... Dishwashers

Bosch Sensomatic Water never comes on. Everything looks fine, all electric looks ok, no water in bottom. I turned it on, opened it to add a spoon, closed it and the water never started running


Do you know your model number? ... Bosch 24 in. SHU43 Built-in Dishwasher

Zanussi DES 959 - AL5 warning keeps coming up indicating either the filters are blocked or there is no water coming in. Filters are clear and there is water coming in - what next?


... Dishwashers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

When the washer is fitted up ready to use the water comes through the handle ,i took the end piece off ,the water then comes through to where the end piece fitted on,when i looked through the end piece i can see straight through so it doesnt seem to be blocked with dirt ect


Check o rings washers ... McCulloch FH160G Pressure Washer

Model WDB212RBMO (1994) is leaking where the water comes into a plastic piece on the side. It connects through to the inside.The piece is molded to the unit and has a hole in the side that looks like it was designed that way. No idea why. But this is where the water comes out while it's filling the tub.


... Westinghouse Dishwashers

Trying to troubleshoot kenmore dishwasher. water is coming in and out like it's supposed to. doesn't look like the spray arm is spinning although water comes out. help!


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Kenmore Dishwashers

Even after ensuring that really hot water is coming from the faucet and placing the unit on the Delicate/Econo setting we consistently get a 2 HR reading. We have also had it where the unit gets stuck on Cycle 1 and we have to reset to go to CL and clear the system of its waste water. Is this a mechanical issue or a circuit board issue.


Did you discover the source of the 2HR reading? Mine's doing the same thing, except the drain pump keeps running and running as well...\015\012Any ideas?\015\012I can't imagine it's anything but the circuit board (for the third time in t ... Bosch SHU5316UC Dishwasher

Bad smell This is more of a general question. When I run the dishwasher there is a bad smell as it fills with water. It comes out of the sink/garbage disposal. I have cleaned out the line that comes from the garbage disposal to the drain and that doesn't stop the smell. Is there a line that needs to be cleaned from the dishwasher to the sink or how can I fix this issue? My dishwasher, at the drain, has water standing and it smells. I think it is there from condensation as the dishwasher, unknow


Smell is not the fault of the dishwasher but your waste disposal unit - they stink!it may be awkward, but arrange your drain so that there is a water barrier. better still. install a standpipe for the drain, again with a water barrier ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

My dishwasher was not getting the dishes clean, so i started taking the lower end apart to clean, got to a gray wheel looking object with a screw in the top which was recessed and still the wheel looking object will not come off, it will spin but will not come off, I need to finish taking it off because I dropped a screw down in the bottom area where the water settles.


If there is still standing water in the bottom of the dishwasher, remove it with a wet vac then look for the missing screw. It might be in the vac.\015\012\015\012If no luck, try using a good small stick magnet to retrieve the screw. The ... Maytag 24 in. MDB4000 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1350 seconds