Having problems with your KitchenAid 24 in. KUDI02IR Built-in Dishwasher ?

I have power to the unit but there are no lights on door when closed. Unit will not respond to any buttons and lock not on.I have opened up the door panel and have power to the door switch and then to the board.What is my next thing to check?


Answers :

Ok so you have power going to the unit at the bottom if the unit is not under warranty? first are any LEDs operating at all when door is opened? if not you most likely have a control issue to test this you would remove the screws along both sides of the inside door and remove the panel you would be testing to assure you have power going to the electronic control if you do then most likely the electronic control has a fault in it and would have to be replaced noted in this diagram as part number 11 http://www.searspartsdirect.com/partsdirect/partsdirect/showSubComp.pd?imageUrl=http%3a%2f%2fc.searspartsdirect.com%2flis_png%2fPLDM%2fW0702129-00002.png
\015\012you can also check the door switch as well which is part number 12 but if 12 were at a fault you would still have a visable LED on your door if you have any further questions message me back and please remember to rank how this opinion has helped when our chat has fully concluded Thanks Rick
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have power to the unit but there are no lights on door when closed. Unit will not respond to any buttons and lock not on.I have opened up the door panel and have power to the door switch and then to the board.What is my next thing to check?


Ok so you have power going to the unit at the bottom if the unit is not under warranty? first are any LEDs operating at all when door is opened? if not you most likely have a control issue to test this you would remove the screws along both sides of ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

My Kenmore 665.15962990 has just quit working. There is water in the bottom that did not drain. The panel is just dead, none of the digital spaces will respond to touch. The stock #15962. There is power to the unit. The door switches check out OK. What should I check next and how?


You have a blown thermal fuse. You can change this by unscrewing the the inner door from the outer door and changing the fuse part#3376359 here is a picture to help you see how to open the unit up.\015\012 ... Kenmore Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Whirlpool dishwasher model # DU1055KTP34--washer stopped mid-cycle---no power at panel---removed panel and checked door switches--one showed 5 volts and switched other showed line voltage and switched


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

Kitchenaid model KUDIO1ILBL6 The lights for Heavy Cycle ,Normal Cycle and Cancel blinking at the sametime constantly. The tech sheet is missing and the unit is appox. 5years old.have shut power down for 5 minutes .When power turn back on only the Heavy Cycle light blinks costantly. Have Ohmed out the door switches and check adjustment OK. Checked board strips and plugs for good clean and tight connections OK. Thanks


Hi, You need to reset the unit by pushing the buttons. Push the heated wash/heated dry a few times. All the lights will light up and the dishwasher will continue its . Let ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

No power unit went dead checked power to base of unit ok also shut off breaker for 10 minutes to see if it will reset, no luck. Also removed inner door panel to reveal circut board to look for a reset or small fuse, none evident.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

My Bosch SHE98M will not respond to pushing the Cleartouch buttons. It is just stuck displaying the normal wash. It will not respond to pressing any of the touchpads. When the door is closed it displays "not started". I have powered the unit down by switching it off at the supply, then restoring power but there is no change. It appears as if the cleartouch panel is no longer sensitive to touch?


... Bosch Evolution 800 SHE98M05UC Stainless Steel Dishwasher

The control panel on my Maytag MDBH970AW is unresponsive, and the latch is stuck in the "open" position (the plastic piece stays pushed in to the handle and won't come down). I've checked that the unit is getting power from the house. Last time I had this exact problem (when it was under warranty), they had to replace the control panel, the latch, and it seemed like most of the door. What should I do?


... Maytag 24 in. MDBH970AWS Built-in Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My Kitchenaid dishwasher KUDIO1FLSS1 stopped during the wash cycle. No lights and no power. I checked the power to the washer and the fuse inside the door panel. Both fine.


... KitchenAid Dishwashers

Model mdb7601awb diswasher . Nothing works , no buttons torn on or work when pushed, no action. 1.Have checked power to unit and is ok 2.checked door switches (2) and both work properly. 3. no visual discoloration on circuit board. There is a blue dot on the wiring harness from control board to button panel.When evaluating with magnifing glass I believe this to be blue ink droplet and not any burnning of harness. Need a Guru.


I have had the board replaced 5 times and the entire dishwasher replaced once. It was necessary to go to the state attorney general to get Maytag to extend the warranty. Just called the service center for the sixth time, after this the warranty will ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

Our Beko DE6340 has stopped working. We turned it on as usual and left it to run. Several hours later we opened the door and the was water in the bottom. This has happened before so I slid the unit out took out the drain and reattached. Now it won't turn on. I have taken the top panel off an there is power to the switch but no lights are coming on. Any ideas?


... Dishwashers

Dishwasher is reading "overfilling", but no water is in unit. Door can open, noise of motor or pump continues and will not shut off even with the Power switch. Only way to stop noise is to turn off the circuit breaker at the electrical panel. What does this sound like to you?


HI- The flood switch has been tripped. It is located under the unit and is not really accessible except by a Tech. The most likely cause it poor draining; if there is a little water left over from each part of the cycle then eventually the water ... Asko 24 in. D3530FI Built-in Dishwasher

Dishwasher model: DU1100XTPQ1 The dishwasher started it's cycle and then just stopped. Now none of the lights come on in the front panel. I've tested: 1) Electrical power to the machine checked OK. 2) Two switches inside the door handle show contenuity when depressed.


HI. Your testing has confirmed that the main electronic control board has failed. This will cause an abrupt shutdown. There is a fuse located on the control board. it is mounted on the back side of the control board. test the fuse for continuity. if ... Whirlpool Dishwashers

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

My Samsung DMR77LHS dishwasher has lost power completely near the end of a cycle. About an inch of water remains. I have power to the unit. I checked the 15 amp fuse in the unit - it had blown. I replaced it, but still no luck. The fuse is not blowing, but there is no power to panel. Nothing happens when you hit the power button - no lights or anything. Unit acts as if ther is no power at all. I have seen similar posts. Any thoughts?


Hi, whenever a fuse of that magnitude, or any fuse really, Blows, you should never just replace it, as to have any device, blow a fuse, trip a breaker, requires a major fault, they do NOT blow spontaneously ever. So you have had a major short circu ... Samsung DMR77LHS Tall Tub Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1446 seconds