Having problems with your KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher ?

Waterless dishwasher Kitchenaid Superba classic 21, was working great, then very little water is getting into the machine. No valves have been closed or anything changed.


Answers :

If last solution did not work, check if the wash arms or rinse arms are blocked. best way to do this is to remove arms and see if machine fills. If machine still does not fill, you need to check the solenoid valve.
It is possible an inlet hose is kinked or trapped behind the machine. If they look ok, then there is actually small filter fitted at the front of the inlet to the machine. Turn off water and undo the hose to the machine. - remove filter with pliars and clean.
\015\012I suggest using spray polish on the connector prior to replacing it - it makes life easier and avoids ripping the seal.It's a basic silicone lubricant.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Waterless dishwasher Kitchenaid Superba classic 21, was working great, then very little water is getting into the machine. No valves have been closed or anything changed.


If last solution did not work, check if the wash arms or rinse arms are blocked. best way to do this is to remove arms and see if machine fills. If machine still does not fill, you need to check the solenoid valve. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Hi :) We have a Bosch slimline dishwasher type SRS56A02 GB/08 - it doesn't draw in water - the timer counts down but nothing happens. We checked these pages and cleaned the filters on the inlet water line but no change :( I saw that it might be the inlet water valve - is this easy to get to - do we need to take off panels? if so, is there a manual available please? Over the past week or so it had got noiser - it was at its quietest while the water was draining out of the machine.


... Dishwashers

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Model # gsd3320c04bb. I am getting water to the inlet valve. I tried changing the inlet valve but still no water goes thru it. I am getting 22 V AC at the connector when operating. The only water that is circulating in the dishwasher is the water that is remaining in the pump system. Any ideas as to what is preventing the inlet valve from operating?


Sounds like you need to replace the mixing valve which is where your incoming water lines connect to the back of the washer. ... GE 24 in. GSD3320 Built-in Dishwasher

Electrolux dishwasher upper spray arm not getting water after adjusting rack. it appears the valve in the back of the dishwasher for the previous position will not flap closed. how difficult is this part to change?


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

My Miele dishwasher is about 16 months old. Initially it was awesome. Now it doesn't get anything truly clean on any rack. Every item has scum and traces of food or drink left on it. I've cleaned the filter and the no-return valve, and refilled the salt (yes, I used the right one) and rinse aid. The manual has no other instructions to remedy dirty dishes. The water is hot, and the machine seems to be running just fine. Where should I look for a problem?


The other possible problem is that the spray arms have small bits of food (sesame seeds are nasty!) stuck in the holes. Take the arms off and flush them out. You might need to poke out seeds that are stuck in the holes. ... Miele G880 Dishwasher

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

Hi there My dishwasher (Miele G975 PLUS) drain light keeps coming on and the water won't drain. I can manually drain the water and the machine will then start again but as soon as it gets to the drain/rinse part of the cycle, the problem recurs. I have removed the non-return valve and it was clear of blockages so I am now out of options. The machine is only 4.5 years old. Any help would be appreciated. Thanks


... Dishwashers

GE Nautilus dishwasher. I just changed my inlet valve, and when I turned the machine on, the valve let water in properly, but the sprayer/cleaner did nothing. the machine clicked throuh the whole cycle, but no cleaning


... GE Nautilus 24" Built-in Dishwasher

When cycle starts after about 1 minute bleeping starts and when door opens the machine has changed the programme to the 1st programme (rinse) the light is flashing 7 times then pause then starts again, it sounds like the water is not getting into the machine, we have checked the water pipes for blockage and cleaned the filters?? Model is ADG7440


... Dishwashers

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


... Gaggenau GI936-760 Dishwasher

Our dishwasher seems to be stuck in drain mode. My daughter put the wrong kind of soap in it. She accidently put Regular dish washing soap in rather than machine dish washing soap. We've got all the suds out. Seems to drain water just fine. However we cant seem to get it to add water. Does the soap have anything to do with it? Anything I can do from my end? Please Advise. Thanks


Plastic base is full of water. Need to remove whole unit to access bottom and dry it out. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I changed my water control valve, thinking my dishwasher was not getting water, however, if I put water in the basin, dishwasher pumps the water out, however, it sounds like the dishwasher stays stuck in the drain mode, pump just continues to run?


Hi,\015\012\015\012There is a simple explanation for this - water is leaking into the bottom of your dishwasher under the washing compartment. This has caused the float to rise and trip the switch which activates the Aqua-Stop / anti-floo ... Bosch SHU9915UC Dishwasher

Dishwasher is 16 months old. Recently, it won't get tea stains from spoons or cups and there is a white film on plastics. I have run unit once with vinegar. I tried using less detergent and no change (Cascade Complete). (Neighbors using same detergnet on different machine with no problems so it's not the water.) I always select High water temp and air dry on normanl wash. My hunch is that the motor is going bad and therefore it is not pushing the water with enough force.


Hello, there are a few thinks to check on the dishwasher. Circulation, drainage - no backflow back into tub, and water temp. If all three are good, then you have hard water. \015\0121. circulation - These MDB models are very good with water circul ... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

My dishwasher is a swan sdw7030w, water is going in and out the machine but no water is getting through to man part wher dishes are, am putting it on and it's jumping from my choosen cycle to economy while beeping, the salt light and starish looking 1 are both on as well, can anyone help me? It was working fine n old house, could it possibly be my water pressure as I can't think of anything else as a woman. Please help me.


... Dishwashers

D1796 3-4 years old. Power on, lights flash, but when close door to start d/w, no noises made, water does not flow or anything. Water supply is on. Water valve to d/w open. Worked flawlessly until today.


Check the valve. maybe its a faulty valve.check the pump motor as well, this gives rise to the water. just wish that its not the circuit board because the circuit board costs a fortune.!\015\012\015\012if you say that its been used 3 to 4 ... Dishwashers

My dishwasher is a swan sdw7030w, water is going in and out the machine but no water is getting through to man part wher dishes are, am putting it on and it's jumping from my choosen cycle to economy while beeping, the salt light and starish looking 1 are both on as well, can anyone help me? It was working fine n old house, could it possibly be my water pressure as I can't think of anything else as a woman. Please help me.


... Dishwashers

Loud humming when the water enters the dishwasher. The copper pipe vibrates. The dishwasher is approximately 11 years old. Problem slowly getting worse over time. I tried to tie down the copper pipe in the basement to no avail. When I closed the right angle stop valve and reopened, the problem got much worse and won't go away even if I grab the pipe. Only happens when water enters the dishwasher.


The fill valve solenoid has gone bad.u need to chg the fill valve assly.it is very easy to chge ad it is mounted on lhs bottom corner of the unit behind the toe panel. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1650 seconds