Having problems with your KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher ?

My dishwasher is not quite 2yrs. old and has always worked great until now. Top rack cups and mugs still are dirty inside from coffee, lipstick, etc., glasses have spots and are cloudy, and silverware seems to have streaks and become darker. I always turn hot water on at faucet prior to running dishwasher. I have check the water faucet and it is 120 degrees. After starting the dishwasher I checked and the water is not even 100. After about 20 mins. the water was aprrox. 117 degrees. The


Answers :

Hello,

Welcome to FixYa,

Based on your description I`d suspect a plugged wash pump.

The place to start for that is to pull the pump filter, spray arm and check for food deposit, broken glass, undesolved detergent and general water deposit built up in the sump well.

The key is to get in there and clean it all out, I`ve attached a link at the bottom that will show you how to go about it. It is not really referring to the heating issue, or maybe even your model, ( Most Whirlpool, Inglis, Kenmore, Kitchen-Aid, Jenn-Air ) but it is the same procedure.

When you`re finished run it through a test cycle and see how it goes.

Let me know how you make out and what you find.

macmarkus :)

http://www.youtube.com/watch?v=iRCCrEwrst8&NR=1
Dishwasher smells even after washing a load of dishes. We rinse all our dishes before putting them in the dishwasher.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher is not quite 2yrs. old and has always worked great until now. Top rack cups and mugs still are dirty inside from coffee, lipstick, etc., glasses have spots and are cloudy, and silverware seems to have streaks and become darker. I always turn hot water on at faucet prior to running dishwasher. I have check the water faucet and it is 120 degrees. After starting the dishwasher I checked and the water is not even 100. After about 20 mins. the water was aprrox. 117 degrees. The


Hello,Welcome to FixYa,Based on your description I`d suspect a plugged wash pump.The place to start for that is to pull the pump filter, spray arm and check for food deposit, broken glass, undesolved detergent and ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

It appears that the dishwasher is not getting enough water. I have made sure that there is nothing blocking the door area so that the soap can dispense and I have reduced the amount of detergent to maybe a 1/2 Tablespoon. Have tried both powder and liquid detergents. Ran a sani clean cycle with the Jet Dry product for dishwasher used in the rural. I also run the hot water in the sink prior to starting the dishwasher to ensure the water is hot when it comes into the dishwasher. The detergent


Hello,Welcome to FixYa.Based on your description you`re experiencing the ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

My Bosch dishwasher runs long. I notice the water in the bottom isn't very hot. (I've turned on the faucet and let the hot water run before I started dishwasher.).


Hello,Welcome to FixYa. ... Bosch Dishwashers

My Frididaire Dishwasher Model FDB1250REC1 is discolored inside. Its a browninsh color and it has gotten on my Corningware dishes and stained some of them. I can get most of the color off the dishes if I scrub hard. I have run cleaners for the dishwasher thru and cleaned it temporarly. Do you think this is the soap I use, amount of soap or maybe the water. Not sure its the water cause there is another one on my water line that is not really having this problem. I always run hot water just before


So you need to install a water filter, before you connect water supplie, then you need a special soap to clean wachine (Calgonit diswasher cleaner powder ) use-it without dishes. then use a dishwasher salt (to disolve all water dirt and colour) and r ... Dishwashers

I own a GE Profile Built-in Dishwasher Model number is PDW7880G00SS, Serial number is FF7872828.  We have recently been having major cleaning issues with it, especially the top shelf i.e. the glasses.  There is always dried up debris on them.  We always run the water hot and run it on "added heat" cycle.  I was wondering if there is a filter, or an area in the dishwasher that needs to be cleaned out?  Even if I put perfectly clean dishes in there, they will come out dirty, which leads me to thin


... GE 24 in. Profile PDW7880G Built-in Dishwasher

Dishwasher fix water does not go through the spray,. the upper hand an lower hand are clean , the pump does operate to empty the dishwasher . I do smell like some burning smell when I turn the dishwaher on, the water start running for 1 minute or 2 than stop shortly and doesn t reach the arm then the dishwasher becomes hot inside . Thank you


Something has gotten passed the screen and is jamming your pump impeller pull lower spray arm pull screen and see if you can find what is jamming the impeller and remove it drain pump is separate ... Maytag MDB7100AWB Dishwasher

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

My Kenmore Elite Dishwasher (665.16499300) will not fill with water on the Normal Wash. It sounds like it's going through the cycle, but there's no water. I always run the hot water through the tap first. Oddly, the machine operates just fine in the Antibacterial Wash setting. Help would be greatly appreciated.


This machine is known to have a problem with the control panel. You need to get another one and replace the bad one that is in your machine. You should be able to contact sears and see about a replacement. You might even be able to get it done for y ... Dishwashers

I have Frigidaire FDB956RBC1 diswasher. I have to turn off the water to fix the faucet. When I turned the water back on, water did not go to the diswasher when I used it. The diswasher runs normal except with no water going into it. The water runs find at the facet. There is separate water supply underneath the sink for the faucet and the diswasher. I wonder if there is a mechanism with the dishwasher that stop the water from going into the dishwasher after the water supply been turn off. I did


FRIDG... EXPERT HERE \012\012\012Welcome to fixya\012\012Hello\012\012 \012\012 ... Frigidaire FDB956RB Built-in Dishwasher

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

All of a sudden the dishwasher water is not hot (usually the water is very hot when wash the dishes ).... even when I put the hot water sink tap running out hot water... then start the dishwasher. the rinse cycle only warm water ... usually the water is steaming hot and drying cycle the dishes are too hot to touch ....


Check the heater. Heater control circuit. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

My dishwasher DW60 does not complete the program and drain the hotwater leaving hot water in the bottom of the dishwasher however when I run a prewash cold water cycle the water does drain away and the dishwasher program works correctly do you know why it drains cold water okay but not hot water


... Dishwashers

DO I NEED TO RUN HOT WATER IN THE NEAREST FAUCET TO START THE DISHWASHER


This model does have an inline heater to heat the water to the proper temperature, but it does take a long time and you are recommended to run the tab on the faucet from which the dishwasher water line is tapped from. This clears all the cold water f ... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

Frigidaire dishwasher shows an error code of ER uo after only a small bit of water runs into the dishwasher shortly after the hot water starts running into the dishwasher upon starting the dishwasher up.


... Frigidaire Dishwashers

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My Professional series dishwasher does not work properly. It is only 1.5 years old and glasses on top rack get sprayed with fine layer of particles every time I use it. Other items, top and bottom, are often not clean as well, but glasses are the hardest to re-clean. I have tried evacuating the water left at the bottom of the dishwasher before running, pre-running the hot water in the sink and ensuring that the disposal was run, removing and cleaning the filter at the bottom of the washer. None


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Frigidaire PLD4375RFC Dishwasher

My dishwasher is running cold water not hot. Why is this happening? what can I do? We have hot water running from the sink.


... Siemens 24 in. SE25A831 Hi-Line Free-standing Dishwasher

GE Triton XL Dishwasher won't start, Runs but won't allow the hot water to enter the dishwasher at the beginning of the wash cycle. Just hums with no hot water.


Check the float switch make sure it not stuck or may be full valve gone bad ... GE Dishwashers

LG dishwasher I have just installed an LG dishwasher. When I try to run the dishwasher it sounds as if it is getting no water. I checked the water supply line twice, and nothing is blocking it. The line is attached to the hot water under the sink and is open.


I bought a stainless steel Lg less than 15 months ago for 800.00and it stopped working. The manufacture said so sorry even though you didn't take delivery until the end of Jan. your warranty goes by purchase date. I would of been better of with a may ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2525 seconds