Having problems with your KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher ?

In line fuse blows 4-5 X/yr. i buy the fuse online at $15 but i am getting sick of changing it. what is causing the fuse to blow? model KUDSO1FLSS3.


Answers :

First how often is the fuse blowing? does it blow immediatly or over a couple days some dishwashers have a type of tar like substance that is supposed to protect the wires on the inside of the door this is actually one of the worst things they did when manufactureing the machine instead of protecting the wires it eats away the coating on the wires making them easily exposed to the metal against the door which causes the fuse to trip often. also you can check the ground which should be properly screwed into the frame of the unit located down the right bottom side as well. You have two options in which you can disect the front panel and turn off the power and go wire for wire doing continuity tests to find the actual break in which line and checking each wire visualy for cracks to see if any are shorting against the unit also checking to see if there is any water getting into the area around the handle as well I have seen a couple posts where water has dripped down on the inside of the door and caused this same occurance. Another choice would be less time consuming would be to replace the entire harness assembly as well. Make note of any areas that you do find any scorch marks against the panel this would be your problem area. If you have any further questions message me back and please remember when our chat has fully concluded to rank how this opinion has helped it allows me to help others in similar situations in the future Thanks Rick
Kitchen.manualsonline.com/manuals/mfg/.../kudi02irbs.html
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

In line fuse blows 4-5 X/yr. i buy the fuse online at $15 but i am getting sick of changing it. what is causing the fuse to blow? model KUDSO1FLSS3.


First how often is the fuse blowing? does it blow immediatly or over a couple days some dishwashers have a type of tar like substance that is supposed to protect the wires on the inside of the door this is actually one of the worst things they did wh ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

The thermal fuse blows out midcycle. It used to occur about every 6 months but is getting more frequent


The first thing I would inspect is the heating element for damage that may beginning to short out.If the element checks out good, a failing motor could blow the fuse.If the motor checks out, look for shorts in the wiring both ... Dishwashers

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

Kitchenaid Dishwasher thermal fuse keeps blowing


The reason the thermal fuse is blowing could be due to a loose contact in the wiring or the motor is requiring more power to operate causing the fuse to burnt again. ... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

ZANUSSI DA6141 Dishwasher Stops about 10min in, and it blows the fuse in the plug, open the door and water is hot, I change the fuse and set it on drain and it drains ok. I looked at the On/Off Switch it appeared to be discoloured so I ordered a new one changed it with no problem but the dishwasher stopped at exactly the same point (I know this as I marked the dial) Any help would be great thanks Nick


... Zanussi 24 in. DA6153 Free-standing Dishwasher

My kitchenaid dishwasher keeps blowing the thermal fuse behind the door.. Have replaced it 4 times. Now it will run through one cycle and blow fuse. Any suggestions on what other part could be causing this problem?


... Dishwashers

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Kudc10fxss4 I have a KitchenAid KUDC10FXSS4 w/o any power. Circuit breaker is on, and it's getting power. But there are no lights on the display. I called a parts place to see if I could order a thermal cut off fuse. But the representative stated there is no fuse listed for this model. Any ideas on what would be causing a loss of power? Seems odd/wrong to me that there wouldn't be a fuse. If there is a fuse, would it be located in the door (the control is built into the door, such


... KitchenAid Dishwashers

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

Bosch dishwasher SGS43T52GB Causing main fuse to blow


... Bosch Dishwashers

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Not sure how to get the front off to get to the electrics to change fuse as there is power to the dishwasher


There is no electric fuse inside the dishwasher.\015\012\015\012If you do not see any power on the dihwasher it is likely the thermal fuse has blown. The thermal fuse is part of the heater assembly at the base of the drawer.\015\012 ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Hotpoint BFI680 Dishwasher blows 13 amp fuse about 30 seconds after wash starts. Should I bother trying to get it repaired or just get a new one. It is 8 years old. I am assuming heating element is broken. Parts alone are 70 euro plus labour.


... Dishwashers

Hi my Whirlpool ADP6000WH dishwasher is showing an Error 1 code - longer inlet time so its not getting any water. The tap is definately on and nothing has changed since last time it worked ok with no faults. Possible causes? Thank you.


... Dishwashers

Our Bosch SGS 5091/13 gets about 1/3rd of the way around the dial and then blows a fuse on the house switchboard.Element or wiring??


... Bosch 24 in. SGS4072 Free-standing Dishwasher

Electrolux ESL 63010 dishwasher. This worked fine until the door catch broke. I replaced the catch but could not remember which way round the two electrical leads went (red and black). I tried both ways with the same result. The lights come on the control panel and I can change the programme, but on closing the door the house fuses blow. I have checked the earth cable is fine. Any ideas?


Red - is active powerblack - ground or neutral ... Electrolux Dishwashers

Bosch dishwasher fuse keeps blowing as soon as it is changed and the plug socket is switched on. There is a flash coming from somewhere away from the socket itself, but it is hard to work out whether it's behind the dishwasher or to the side of it because it's obscured.


... Bosch Dishwashers

Kenmore thermal fuse keeps blowing and im getting a white powdery film


If the thermal fuse blows it is a direct result of heat. The most common place for the heat to be generated is the wire connections to the fuse, the wire connections on the main control board and the door switch. The thermal fuse comes wi ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

Hi got a baumatic dishwasher bkd62ss.1 model, it gets half way between the last cycle and cuts out and blows the circut board switch, can turn dial and wee bit and re switch circut board and away it goes again. what would be causing this problem. had dishwash for about 3-4 years? thanks


... Baumatic Dishwashers

Think it may be electrical, tried changing fuse, no response from machine at all when I switch it on, on my karcher wher locally can i get it checked out i live in walsall in the west midlands


... Pressure Washers

Our Maytag Quiet Series 400 has stopped getting the dishes clean..It leaves residue and food on the dishes.My husband has taken it apart and there is nothing that he can find that might cause this.We have changed dishwasher soaps etc I do have to point out that the "Auto Clean" on the panel no longer works


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Maytag 24 in. MDB9750AW Dishwasher

Maytag quiet series 100. leaving white residue on dishes, and residue caked up on bottum od unit.have already tried cleaning products and changed different soaps what causes this and how do i prevent it.how do i get rid of it?


The problem is hard water. go to www.dishwasherfilter.com and get a filter. it is guarnateed to work and very affordable. money back guarantee but trust me you will not ret ... Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1211 seconds