Having problems with your KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher ?

Kitchenaid dishwasher model KUDM01TJB0 Fills with water, heats water but pump dosent run in wash (dosent spray water) Drains water. Every thin appears to work but the pump in the wash mode. I checked the control board and it has no visable issue.


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kitchenaid dishwasher model KUDM01TJB0 Fills with water, heats water but pump dosent run in wash (dosent spray water) Drains water. Every thin appears to work but the pump in the wash mode. I checked the control board and it has no visable issue.


... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

My Maytag mdb5130aww dishwasher stopped working; the only function it does is DRAIN. The panel buttons light up. WASH, RINSE etc all do not work. How do I test if the control panel is sending out power to the water pump? What else can I check?


... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers

Bosch shu9925 At the start of the cycle, the washer is in pump mode. It remains that way. No water flows into the washer.. It just continues to pump. We checked the drain, some debris and checked to see how the pump was working, it is fine. Any suggestions?


Take bottom front panel off to expose the bottom tray. you will find there is water in it. mop water out and appliance will operate ok. turn off at mains first.\015\012\015\012if fault reoccurs, you have a leak which will have to be trace ... Bosch SHU9925UC Built-in Dishwasher

My Maytag PDB3600AWX isn't working. The motor hums as if its working but no water is in the tub. I did put a pitcher of water in the tub to see if it would pump out and it does. I don't know what else to check for. We have had lots of problems with this dishwasher, its never washed the dishes well and has flooded my kitchen to the point of having to replace flooring. I thought its was because we had just had new flooring installed and when they put the dishwasher back in the counter the hose was


... Maytag PDB3600A Built-in Dishwasher

I have a whirlpool dishwasher and I recently changed my disposal and now the water is not pumping out of the dishwasher. I have checked the hose for kinks amd ran my shopvac down the waste water exit and it is not pluged. Is there a way or a mode that I can test my pump to see if it is not working?


You did knock the plug out of the disposel before you hooked dishwasher up to it right? ... Whirlpool 24" Black BuiltIn Dishwasher Dishwasher

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

My dish washer fills with water washes but fails to empty so when door is opened plates are washed but water is left in the bottom the pump must be working as it doesnt leak is the controller faulty on that phasae of the cycle


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain ... Bosch Dishwashers

My hobart lxi pumps down after each wash cycle Already Tried: Cleaned all three water level probes Checked water inlet solenoid (all good) Checked inlet water pressure (all good) Checked drain pump which is supposed to pump out 3/4 of a gallon at the end of each wash cycle but it pumps 2-1/3 gallons then pops up the infamous wrench!


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Water pump runs all the time (for hours on end, cycle will not complete, dishwasher does not wash at all, I have good water supply coming to the water control valve, all lights and buttons on it work ok.


The timer is bad. change it, do you have HOT watter?\015\012How hot is it\015\012Vitally ... Dishwashers

Dishwasher does not drain all water after wash, code C=drain hose,coase or fine strainer or sink blocked.(all checked & are ok) then towards end of wash code H= Call AEG service force ,comes up. but if i put machine on pre-rinse it driains ok, so pump is working. only seem's to be end of wash programe fault accurs


... AEG 22 in. Favorit 55750IM Built-in Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Machine cannot finish cycle and is stuck in pumping out mode. Only tiny amount of water in drain basin at bottom, no excessive water. Was set at 10pm, still attempting to drain 8am! Has no diagnostic dials or manual over rides so continues on whether door is open or closed, even if I switch off and on again. Possible related issue, recently finish at end of washes has been "grainy", far from perfect, surfaces slightly sandy feeling.


... Bosch 24 in. SGV43A03 Built-In Dishwasher

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.


You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers

I'm trying to get my GE GSD1200G00WW to work. When it is put on the wash cycle, I can hear the pump running but the tub does not fill with water. I checked the float and it seems fine. Water valve maybe?


Confirm 120V across the water valve terminals in a couple of minutes into a wash or rinse cycle. (when you turn it on at the beginning of the wash cycle it will drain first, and then will energize the water valve to fill up.)If there is 120V ac ... GE GSD1000 Dishwasher

The pump is working and drains the DW if you pour water into the drain. The problem is that this thing appears to be stuck in "drain" mode always pumping out not advancing through the cycle no matter where you turn the control knob to.


You probably have a stuck solenoid which routes the water either to the arms or out of the machine. It is located near the motor and routes to the drain line. Most are removable and may be disassembled for cleaning. If the control knob does not ad ... Dishwashers

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

Dishwasher malfunction...control panel indicates "IE"...."inlet error"....or water fill error. Machine will not transition to wash mode as a result, even though all the test modes seem to check out ok.


HI. This particular unit is equipped with a defective main PCB board. The solder junction points that hold the relay for the inlet operation are poorly manufactured and soldered. In fact, the entire board is faulty(bad manufacturing). There is also a ... LG Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2310 seconds