Having problems with your KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher ?

Dish washers wash cycle dose not run if i unplug ribbon to circuit and plug back in it runs fine

\015 Lights come on touch panel only rinse cycle works once the power ribbon is un-plugged and plugged back in it will work for 3 or 4 washes and then problem is back\015

Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dish washers wash cycle dose not run if i unplug ribbon to circuit and plug back in it runs fine


... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

Whirlpool quiet wash plus DU920GWGD4 runs after cycle is finished. Just hums, no blades turning. No sign of leak... If I turn circuit off then back on it is fine until it runs a few times again. ...any ideas


Water air lock problem. Check your inlet for free flow.Pour water from the front and mostly it will ease the problem. After this cycle it should work OK. The humming is due to water starvation in the motor. ... Dishwashers

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

Hi, Where is the reset button on the Whirlpool Gold Quiet Partner 111 Dishwasher /Model GU1200XTLT3, Type 575-0. When I had my sink faucet replaced, the Control Lock light came on and I couldn't run anything on my Sensory Wash Cycle panel. I tried unplugging it for a while, no luck. All the circuit breakers are fine. THANKS FOR YOUR HELP! Kathy Bonner


Hi kalybon,\015\012\015\012  There is no "RESET" button on Whirlpool Gold Partner 111 dishwasher. :(\015\012\015\012Regarding your issue, it seems to be a case of Control Card.Sorry to be bearer of bad news, you need to replace ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers

I just bought the Kenmore Ultra Wash Dishwasher model # 665.1389. It worked about 4 times then before the it finished it lost power while it was running. Now it won't turn back on at all. I done everything in the trouble shooting manual and nothing worked. It's not the circuit breaker either. Everything else on the same breaker works fine. What could it be?


... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

Kenmore dishwasher Mod 665 13852K601. MANUAL WASH and CANCEL lights are blinking simultaneously. I unplugged washer and plugged back in. Same thing. Nothing happens when any button is pushed. What's going on?


... Kenmore Dishwashers

Have a 2400 karcher press. washer engine starts runs fine for 15 sec . then quits .I walk away and come back in 10 minutes does same thing. Checked tank and it is not plugged. Appears to have vacuum fuel pump. could that be problem?


It sounds like the fuel bowl is not filling quickly enough. Turn the fuel tap off. Then take the fuel bowl off the carby. You will see a plastic float. Above the float is a needle (small pin like) that should shut the fuel off & let it run also. Turn ... Karcher G3025OH Pressure Washer

I am washing my house with the washer wide open to 3/4 open. It will run fine and hard for 4 to 7 minutes then bog down and shut off. It has new fuel, spark plug and the air filter is clean. What else can I do??


... Pressure Washers

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Hi In the middle of a wash cycle, my dishwasher tripped the circuit breaker on the wall. I diagnosed this by unpluggin dishwasher, plugging in a different appliance and switching circuit breaker back on. new appliance worked OK. When dishwasher had cooled, I tried it again on same circuit (which I knew was working properly). The lights came on for about three seconds, and then the circuit breaker cut back in again, so I knew it was the dishwasher that was causing the problem. Is there anyt


Ck the connections where the cord hooks to the wiring harness. look for hot or shorted wiring . also ck the contro panel for the same . generaly if you have a power draw like you are saying then you can see t ... Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

My bosch dishwasher runs fine, cleans fine, drains fine....but after it has been just sitting for a while, the bottom very slowly fills up with water. Each time we run the machine the water level drains back to the normal amount in the bottom of the washer after the cycle is complete. The problem is if we are away for a few days, the bottom fills up and overflows onto the floor.


Water inlet valve isn't closing all the way closed. Need a new one ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a SHU43C05UC/22 Bosch dishwasher that runs fine till it gets to wash then it seems to stick there. the timer times down to 1 and it stays there for a really long time. it doesn't appear that the washer ever gets out of the wash cycle. when you stop/open the door there is still soapy water in the tub. You can cancel the program and it will drain the tub fine then you have to select rinse and hold to clean out the soap out.


... Bosch 24 in. SHU43 Built-in Dishwasher

Have SHU43C and have had no problems with it. We usually run it on the Quick Wash cycle, but ran it on the Regular Wash cycle yesterday because the glasses seemed to be coming out spotty. After it ran, there were no lights on the display like there usually are. The washer had run and the dishes were clean, but it has not drained completely. There is still about an inch of water in the bottom, despite removing and checking both the Large Object Trap and Fine Filter (neither which were clogged


The drain pump needs to be replaced or cleared of obstruction. ... Bosch 24 in. SHU43 Built-in Dishwasher

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

G851 SC Plus started to trip GFI plug. Called Miele and they said there was nothing wrong with the dishwasher and the GFI was faulty. Unplugged from GFI and plugged into regular plug and it worked for a few days. Eventually stopped running. How wrong Miele was, it had everything to do with the dishwasher and not the GFI. It was only warning me a problem was coming. Appliance man came out, noticed water in bottom pan and order new pump, said seal probably gone. Came back, replaced the pump, put d


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

It appears that water is not running through the dishwasher or that the sprayers are not working correctly. There doesn't appear to be a clog. However, I did find a round rubber "washer" (I think that is what they are called) laying in the bottom of the dishwasher - where does this part go. It was working fine until this wash. The heating element works fine but like I said it appears that something may be wrong with the spray tower. Please advise Model number of Hotpoint: HDA3420Z01BB T


Hi,\012When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... Hotpoint Dishwashers

My Beko D3422 FS was washing normally and the residual current device tripped approximately half way through the cycle. I have unplugged the dishwasher and checked the plug socket with various other appliances. None have tripped the RCD. I have stripped the Dishwasher to look for any disconnected terminals or shorted wires and cannot find anything obviously burnt or any signs of shorting. The 13amp fuse in the dishwasher plug is fine. Are there any components I can test or replace which wouldgi


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1395 seconds