Having problems with your KitchenAid 24 in. KUDP01DL Built-in Dishwasher ?

Washer went dead. replaced thermal fuse and it worked for about a week and went dead again. Before going dead it seemed to take it a long time to do a load of dishes. The last load ran 1 1/2 hours and still showed 45 minutes to go on the timer before it quit completely. Any ideas?


Answers :

Sounds like you have a bad control board on unit.and the reason the thermal fuse went out is one of the relays are getting stuck on unit. before long the fuse will go bad again when the resistance level gets to high again. i would replace the control board and you should be fine...good luck to you...
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP01DL Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Washer went dead. replaced thermal fuse and it worked for about a week and went dead again. Before going dead it seemed to take it a long time to do a load of dishes. The last load ran 1 1/2 hours and still showed 45 minutes to go on the timer before it quit completely. Any ideas?


Sounds like you have a bad control board on unit.and the reason the thermal fuse went out is one of the relays are getting stuck on unit. before long the fuse will go bad again when the resistance level gets to high again. i would replace the control ... KitchenAid 24 in. KUDP01DL Built-in Dishwasher

My LG Dishwaser LDS4821 all of a sudden has been making a very load noise after a few minutes. This has been happening the last 3 times I have ran it. (also ran it empty, noise is still there.) Is this a problem with the motor? I don't hear it on the rinse cycle. This is less than 2 years old.


First, remove the sump cover in the bottom of the tub to check if any object (like a part of a broken glass or plate) is being knocked around by the impeller or hard food cutter blade. (Note: The screw on the end of the motor shaft has a left hand ... LG LDS4821 24 in. Built-in Dishwasher

Wont start I've had the washer for many years with minimal problem. Yesterday when I closed the door no light went on and the washer would not start.  After 20 minutes or so it suddenly went on and worked fine.  I thought that it might have not completed its last cycle. Today, however, I had the same problem and it's been over an hour and still hasn't started. (I checked the circuit breaker and it's fine)


Give it a firm push over the door latch once you've closed the door..it might be the door switch not activating. oops.... first and formost isolate from power for 5-10mins and try ... Bosch 24 in. SHU43 Built-in Dishwasher

Draining problem Water left in dishwasher after end of cycle. Have a disposer, don't have a drain air gap that I can see. Tried to do a cancel/drain, showed 2 minutes ended and water still there. Disposal works fine. What is really interesting is that there is only two of us and at most we've only used the dishwasher thirty times since we had it. Of course- service plan ran out last year (July 07) Please help me. My name is Donna


There is a flapper in the drain hose just where the hose attaches to the pump assembly it has been know to get dislodged and cause a partial drain. With towels underneath hose remove drain hose and stick you finger in and see if it is free moving. ... Kenmore 24 in. 16539 Built-in Dishwasher

I have a GE Quiet Power 3 dishwasher that was working fine last week. Over the weekend I ran it and we could hear a banging noise, so my boyfriend opened it three or four times in a row (during the cycle) to figure out what it was. The fourth time, it went dead. I checked and it had tripped the breaker. I reset the breaker and the dishwasher seemed to be working again, however the lights on the front were flashing (they hadn't previously), and now it will run for about 10 minutes but no water ru


Were you able to figure this out? We have the same problem here! ... Maytag Dishwasher

Bosch SHY66C My Bosch dishwasher won't fill with water.  All electrical connections are fine and I can hear it make a sound as if it is trying to start about every 2 minutes.  There was water in the bottom so I used a shop vac and pulled it all out but it still won't start and is doing the same thing.  I checked the solenoid with a multi-meter and it appears to be working.  My power went out last night for about two hours and that's all I can think of that might have affected it.  The dishwasher


I'm a novice on this question, but i agree with the above statement about check the stuck float switch or check for a bad safety switch or lockout switch of some sort. I would suspect something is definately faulty in that area. Will the dishwasher r ... Dishwashers

We closed the door and dishwasher ran for a few minutes and quit. Wife went and opened door and closed it again and it ran a minute and quit-for good. Any ideas.


You will need to change your fuse in the control panel. this is what usually causes the issue. ... Whirlpool Dishwashers

Takes more than 2 hours to complete a one hour cycle. Will sit on "1" minute left for the last 45-60 mins. If the door is opened during this long one minute the washer still has water in it and will reset to 13 mins remaining.


Hello,\015\012\015\012Welcome to fixya.\015\012 \015\012**What I`m about to share applies to Almost all Electronic control B/S/H/ dishwashers. That includes Bosch, Thermador ... Bosch SHU5315UC Dishwasher

We got our maytag 300 quiet series about 3 years ago from home depot. about a year ago the option buttons/lights on the right side went dead. It was out of warranty and still worked so i ignored it. Now last night, the left side buttons/lights still work, but the start button is dead. It wont run at all. Any ideas?


Our Maytag dishwasher (an earlier model) quit too. Found that the door latch operates two micro-switches which supply power to the machine and one of the switches no longer made contact when operated. The switch pair and the plastic latch parts are s ... Maytag 24 in. MDB5651A Built-in Dishwasher

Bosch dishwasher SHX46A -cycle runs too long (4 hours)- items still wet. The economy cycle also runs too long - should be about 80 minutes and it ran for 200 minutes.


It sounds like there's a problem with the dishwasher's heating element. The dishwasher uses the heating element to heat the water to certain temperatures, and it will wait (run for extra time) for the water to reach this temperature, and may eventua ... Bosch 24 in. SHX46A05 Stainless Steel Built-in Dishwasher

I have a Frigidaire dishwasher that's just over 1 year old and I use it a couple times a week. I turned it on last night and went in another room. appox 30 minutes later my daughter came in and noticed the soap suds all over the kitchen floor, the inside was all sudzy. It was in the wash cycle so I turned it off just by opening the door for overnight and restarted this morning and after about 20 minutes (still in the wash cycle) the suds started oozing out so I that's where I'm at now. Thanks.


Hi,Someone squirted dish soap in there instead of regular dishwasher detergent...You will need to manually rinse out the soap and use the right soap...heatman101 ... Dishwashers

Bosch SHU6605UC may start @ 199 minutes,run for over 4 hours,the last hour showing 1,all clean dishes/glasses,louder than used to be.Cleaned white slimmy film from filter cup screen/housing,not much change.what next?


... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Kenmore model 665.16509200 Does not clean very well and now dry cycle not working. Wash cycle takes almost 2 hours, and still dishes had gradoo and white detergent on them, even ones that were clean when they went in. The drying coil had plastic melted on it once before, so that could have caused that malfunction. I am not so concerned about that, it is the dirty dishes after 2 hours that is driving me nuts. The short wash cycle leaves EVERYTHING dirty, so I just quite even trying that.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

Bosch Dishwasher I have a Bosch Dishwasher that is a little over a year old. Loaded it up and ran it last night. Got up this morning to unload it, and load it again. Got it all set and went to start it but there is no power. The circut breaker looks fine. But no power to the machine. Not sure what is going on, or what needs to be done. Thanks....


... Bosch SHU3306UC Built-in Dishwasher

So i have a maytag jetclean eq plus MDB7100AWW not sure how old it is as it was in my condo when i moved in 6yrs ago and there was no paperwork with it. The dishwasher worked fine until a couple days ago. The last load that i washed came out with a white film on everything, i checked the jetdry it was empty so i filled that and ran another load, everything was still covered in the white soapy film. So I tried running a dishwasher cleaning product through it, that didnt help, i tried running it w


... Maytag Dishwashers

I have an 2002 Eclipse with a locked out radio. The dealer told me to turn the key to on w/o starting the engine, turn everything on and in an hour or so the radio would rest. After 2 hours and a dead battery the radio is still locked. I tried disconnecting the battery for a few minutes and that did not work either. Do you have any ideas?


Call the Mitsubishi 1800 manufacturer # and give them your VIN so they can give you the unlock code for the radio. ... Dishwashers

Maytag mdb9150 dishwasher stopped at some point last night--found it this morning with flashing lights--I think "clean" and "heated dry", not sure.  I used "drain/off" to make sure there was mechanical noise--there was, so I don't think the machine is dead.  Purchased on 2001 with 5 year warranty, so out of luck there.  I tried turning off the electricity to the unit for a few hours; nothing improved.  When you start it (or think you have!) it makes noises for about a minute that sound promising


Check pump and solonoids click/work, if no mechanical noise, could be the circuit board, but they can be expensive. :(\015\012if the solenoids click, and allows water in, then the pump might be jammed, with grit, clean and reinstall... good luc ... Maytag 24 in. MDB9150A Built-in Dishwasher

My dishwasher ran for 4 hours last night. When we realized that, we opened it and it was still soapy. Is it likely that I need to replace the timer?


My dishwasher will not come out of the wash cycle. It is flashing HO on the display. I've not use it but a few times over several yrs. has something gone bad? ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Ther's a foul smell coming from the dishwasher evert time I open it. Doing a wash does not solve this. I'v had this since it was new, months ago, and have had the installer look at it, said it wasn't his problem. Had a tech. come in and said it wasn't his problem. I've owned many dishwashers and never has it had a foul smell. Last fall I went to Nova Scotia, ran the dishwasher before I left, came back in two weeks and noticied water was still in the bottom of the dishwasher-it didn't drain all t


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

I have a whirlpool for Ikea dishwasher that is built in and I put it on the normal 30 minute cycle before I went to bed and 8 hours later it was still going. I opened the door and machine was full of suds. It is like it gets stuck and can't move on to the next part of the cycle. I have checked the filter in the bottom of the machine and checked the salt and rinse aid levels.


It could be waiting for the temperature to reach the required level.\012\012Sounds like the heater element has died. ... Whirlpool Dishwashers

When we start the dishwasher running it just continues and continues and continues. For example earlier we set it for a normal cycle after almost an hour it still showed 44 minutes to run - and seemed stuck on that number


Replace timer ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

It hasn't been used much and a couple of months ago it ran just fine. I went to do a load of dishes and it is just dead. Nothing is working. I flipped all the breakers to see if that was the problem and it was not. Is there a fuse or something that can blow?


Flip every wall switch in your kitchen,while having door latched and turned to a run mode of some sort.be sure to check under kitchen sink for any hidden power switches as well.8 out of 10 ge d/w with this issue usually revert back to a wall switch ... GE Nautilus 24" Built-in Dishwasher

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

DISHWASHER PROBLEM HI, Last night I ran the dishwasher down in our kitchen down stairs. Four hour later I heard a humming sound coming from down there. I noticed the dishwasher went through the cycle perfectly , except on the hot drying cycle the timer knob was stuck and won't budge. I cannot move it either way. So I just unlatched it. Want do you think happened?


Do you see any error message on the display? ... GE Nautilus 24" Built-in Dishwasher

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0982 seconds