Having problems with your KitchenAid 24 in. KUDP01DL Built-in Dishwasher ?

Going to install new computer board. how do you reprogram the dishwasher kitchenaid model #KUDP01DLBS0


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP01DL Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Going to install new computer board. how do you reprogram the dishwasher kitchenaid model #KUDP01DLBS0


... KitchenAid 24 in. KUDP01DL Built-in Dishwasher

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

On our Hobart Dishwaher, Model AM15T, S/N-23-1000-664 won't start with message wrench & P2. The Thermistor is not open or shorted with resistance reading of 64 Kilo-ohms. I suspect that the Relay Board P/N- 892934-2F is not good. I installed the New spare board P/N 892934-1 Rev.F, but no display at all. Is this the correct PCB? Also the Thermistor is on one assembly with float switc. The new spare we had is only a Thermistor P/N F370609. I also checked the 3- Thermostat on the Tank and they are


... Hobart Dishwashers

Dishwasher I am getting a run around with getting my LG dishwasher fixed properly. We had a tech more than once come in and look at our dishwasher. It has not been fixed and never dried the dishes properly. It is now leaking and going to a "del" level when we attempt to wash the dishes. It is also leaking on our fairly new tiled floor and under our new kitchen cabinet. Your tech stated the dishwasher was not installed properly. The installation dept , Francine stated it is not their problem


Not sure what you mean by a "del" level, but as far a drying issues:\015\012\015\012LG chose to use a very energy efficient drying method which relies on the residual heat of the dishes to help dry them rather than many manufacturer ... LG LDF6810 Built-in Dishwasher

Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?


It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers

In December 2010, I purchased an Electrolux range, microwave and dishwaser for my kitchen. Already I have had to replace the computer boards on my all three appliances. Last night, I load the dishwasher and go to turn on and the computer board is dead again. What is the problem and would you advise that I return all 3 appliances for a refund?


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

Kitchenaid KUDK03IT has just had it's second control board in 90 days stop working. New one is ordered, but I wonder why it is going through control boards.


... KitchenAid KUDK03ITBK Built-in Dishwasher

I have a Bosch Exclusiv dishwasher (Model SGS 8812 GB) which, from installation in January 2002, has consistently caused glassware to go cloudy. This happens after about 8/10 weeks from buying new glasses. I use Finish Rinse Aid and Salt and have an independent water softener installed. This is proving an expensive exercise, as I need to replace glassware every 10/12 weeks. Have you any suggestions, please? Thank you - Doreen Sheardown


You are sandblasting your glasses. The added salt with the salt from the softener is causing the cloudiness. If you are rinsing the dishes to be mostly clean first and using the suggested amount of detergent you are way over sudsing.#1 St ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

We have a kitchenAid dishwasher -- just installed last year new-- we cannot get the rinse aid low light to go off. We have filled it up to where it can no longer hold anymore and the light is still on. I have tried to cut the power on/off and it still remains on. Any suggestions on how to get the light to go off? thank you.


Check to see if the "Heat Dry/Lock" button is lit up. If it is, press the button and hold it for four seconds to unlock your dishwasher controls.Close your dishwasher door firmly and press the "Cancel" button. Wait two minutes for your Ki ... KitchenAid Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I have got a problem with my circuit board on my homark dw45bi any ideas where i can get a new one or fix the old one there is power going into 1 side and coming out of it but not going into the other side any ideas???


... Dishwashers

I just installed a new dishwasher . The water is going to the dishwasher but it wont go into the dishwasher


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

I have a Maytag Model # mbd9601aws dishwasher. I just installed a new control board and new upper display on the dishwasher.When performing a Field Service test the test fails stating a memory failure. What do I do next?


... Maytag Dishwashers

My ge profile dishwasher is making a buzzing sound from the pezio buzzer on the control board. This started after a power outage. I verified power and ordered a new control module. After installing the new part it still buzzes and does not function.


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Frigidaire Gallery (model #GLD4355RFS1) and the control board constantly flashes the error message. Do I need a new control board? Where can I order one and how do I install it myself?


... Dishwashers

Installed a new control board in GE dishwasher: GLD6860NSS. Still having problems!


... GE GLD6860NSS Stainless Steel Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

SHX46A02UC dishwasher will not complete cycle. Just installed new circuit board. Will also run with door open. Seems to be stuck in drain mode.


Test the door switch and its wiring. The dishwasher is supposed to stop when door is open.About drain pump, check the pressure switch and eventually replace it(pressure is water level, this is not the float, that is usually overfill-if th ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

How do I attatch the new plastic water lines to a dichwasher I am going to install? What fittings etc do I use?


Buy an install kit for the dishwasher. (preferably with a braided steel covered hose) That has an end that will fit the dishwasher, then ask at the hardware store what you will need to adapt to the plastic line. I really can't tell you without more ... Dishwashers

We have a commercial Hobart dish washer Model # AM-8T2; Serial # 240461. We cannot get the wash temperature to go above 120' to 150' as the burner does not light. The pilot is on. A new thermocouple was installed but made no difference. The rinse temp goes up to 180'. How can we get the gas burner to light and stay on. Thank you. Gery Spory


Hello Gery - get the repairman back who installed that thermocouple as that repair includes making sure the unit is working properly. Most likely the thermocouple is simply not warming up enough to operate correctly. It may be that the pilot light ... Hobart Dishwashers

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I am trying to install a new Maytag MDBH945AWB Dishwasher and have to run the drain hose under the machine in order to get it to the sink. Each time I try to use the hose that comes with the machine it snaps in two and breaks. I have tried to look for a replacement hose that would stand up to the abuse but all I can find is the original. Is there a replacement I can get that is more flexible than the one that comes with it? At this point I am rather embarrased about going back to Home Depot


Hi...home depot sells clear PVC hoses, They come in various lengths up to 100 ft. You can use hose clamps to connect it to the T-fitting. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1000 seconds