Having problems with your KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher ?

No start the proper buttons are pressed as usual, however the device does not start.


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No start the proper buttons are pressed as usual, however the device does not start.


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Rotary switch selection of washing program.Whichever one selected - machine sounds to start up, whether or not the start button is pressed. However no sound of washing kicks in as was usual and eventually the light over the start button starts blinking and all noise ceases - blinking continues.


Found a local man on the internet, who popped in and leant the machine forward then backwards and then flushed out the system, explaining that the program cycle had gone awry and there was water where there should have been air and so microswitches h ... Dishwashers

Hello, my Siemens integrated dishwasher no: SE64M359GB stopped working mid-cycle with 35mins remaining. It is displaying the red tap emblem. Usually the dishwasher starts when the dishwasher door is closed fully (having pressed the power button). However, it is making a noise as soon as the power button is pressed. I have checked the water supply and pipes and they are OK. The filters are also clean and OK. We have an electric de-scaler on our system so I imagine calcium build up should n


... Siemens Dishwashers

We have a Nautilus dishwasher which we kept during our kitchen renovation. When the dishwasher was installed back in it was tested and all was okay. However when the guys left and we started the machine it was for 98 minutes as against the usual 90 minutes. We were happy with this but now we find that at the end of the full cycle it does not turn off and continually beeps. It will not turn off by pressing the off button and you have to open the door. When you start again it immediately starts wi


Hi\015\012\015\012To reset you can leave the unit unplugged for 1hr, then plug\015\012it back in, you can also reset the controls by pressing the AIR DRY/RINSE\015\012ONLY/HEAT DRY button for 15 seconds. If the issue returns then the circ ... Fisher and Paykel Dishwashers

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Hi there. I have a Matsui MF145 slimline dishwasher and having a problem. When I press the on/off button I would usually then press the program indicator button (usually the first indicator - pans) and close the door and the dishwasher would start. Currently i press the on/off button and try to press the program indicator button and the on/off button flashes and there is a continuos beeping sound....and nothing more happens. Do you know what the problem is?


Try to clean the unit, ofetn when the machine is dirty, some sensors are fooled thinking there's some problem. be sure there's no jam on mechanical parts. ... Dishwashers

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Dishwasher keeps stopping and beeping continuously until I press the start button again and shows the F8 Code. When I press the start button it continues for about 5 minutes and then stops properly but there is lots of foam still in the bottom of the dishwasher.


Sir i think the problem would be in any of the three areas. any prob in these areas would lead to the problem u specified\015\012\015\012Test the timer motor.\015\012 ... Dishwashers

Have a KUDS24SEAL5 superba and no lights come on after pressing any of the buttons. Power to machine is good. Several months ago it would not start properly by pressing 'start'. Would go directly to 'drain' cycle. Then found that if we pressed 'rinse' before 'start' it worked fine. Now, almost a year later...no lights, no one home...any thoughts?


I had a KUDP02CRB and there is a hidden transition connector on the front panel under a black plastic cover that was pulled out a little. It connects the flex cable from the controller board to flex circuit of the panel. I just pushed it back in al ... KitchenAid Dishwashers

When I depress the start button, the timer is clicking to engage and begin the cycle, however, the dishwasher does not start. Other times, there is no noise whatsover when I press the start button and neither does the dishwasher start. If I don't use it for say 2-3 weeks and try again, it starts working for a period of a few months, but then the same thing happens again down the track. This has occurred about 4 times.


Hi.Resetting the breaker means turning power off and back on from the main switch in your house. Same as disconnecting power cord.I am sure that in this case "tripping the breaker" will not help. Repairing appliances is not th ... Dishwashers

Whirlpool "Quietflight II" - Will not start. The button for "Delay" works, and the button for "Cancel/Drain" works. Pressing this button will drain the unit. No other buttons will work, however, and the unit will not start. Ideas? I've taken the control panel off and looked at it's guts, as far as I can tell everything looked ok (not burnt and no loose wires), although I am no electrician....


Have you tried testing the control panel with an VOM meter? You can press a button and test the wiring that would go to that particular circuit. See if you get a reading on the specific wire when that particular wire is pushed. Does sound like a cont ... Dishwashers

I have a zanussi tempoline dishwasher, I have loaded this as I usually do, turn the knob to the right and select the 2nd programme the light next to this comes on, I have pressed this to start the machine although it seems as if it is going to start this light flashes and the top arrow on the right of this flashes intermitanly, but the machine does not start the wash programme. The 3hr delay button if I had pressed this by mistake which I am sure I have not would light up. When I found it did no


Hi Ruth.The machine can be in error mode. In this case one or more lights in the control pad will stay on or flash and the cycle will not start.One of the most common fault in your situation, and at start of the cycle is no wa ... Zanussi Dishwashers

I do not have manual for this dishwasher and am unable to start cycle, has been working up until today have checked obvious things like power and water. I usually press start botton then press P until it lands on eco then >|| button


Possible that the controller unit has got some errors or is faulty. remove the mains plug and keep aside for few minutes. Then switch on to test. If there is no result then you might have to check the power to the controller unit. Use a multimeter t ... Dishwashers

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

Start button pressed - Water loads and "Wash Cycle" lights are on but does not start wash. If "stop/reset" is pressed then all water is properly drained. Tried different wash cycles like "Speed Wash", etc and same problem persists. Have checked interior to make sure no blockage and that washer arm moves freely.


... GE 24 in. GSD6600G Built-In Dishwasher

I'm not able to reset my dishwasher Whirlpool ADG795, i mean, my 4-year old son was playing with buttons and, i think, the dishwasher went, but not exactly properly, into test, all the lights are flashing, i was trying to start the test properly (by pushing power button for 30 sec, hen 3 sec release and press once more) but unfortunately nothing has happened, argh... any idea?


Sounds like you are in the testing/diagnostic mode. You can exit the program by holding the buttons, or simply unplug the unit for an hour, in meantime of being unplugged, press and hold the function or power button for 5 seconds, then wait 1/2 hour ... Ariston Technologies Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My dishwasher will not start. It is a frigidaire / electrolux FDB1050REQ. I have checked thepower....and reset the circuit breaker.......then pushed the start button.....the light comes on on the front of the washer like normal but no water starts filling. I have jiggled the anti water overfill device but still nothing. HELP!!! The front of the dishwasher says Frigidaire, however, the inside of the door where the model# is says Electrolux


... Frigidaire Dishwashers

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Model no 665.17464300, would not start after pressing buttons. finally got washer to work however all buttons are lit up


... Kenmore Dishwashers

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0873 seconds