Having problems with your KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher ?

Kitchenaid dishwasher The clean light was flashing 7 times, so I did read and try the solution SaniRinse-EnergySaverDry-SaniRinse-EnergySaverDry and this did get the machine to unlock and start up. Thank you! But I'm noticing that no watre is going into the machine. I can hear it drain some water. It is very hot and steamy in the machine so no heater problem, but I don;t see any of the soap on the bottom of the machine rinsing away. I'm afraid its stopping because the motor is overh


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kitchenaid dishwasher The clean light was flashing 7 times, so I did read and try the solution SaniRinse-EnergySaverDry-SaniRinse-EnergySaverDry and this did get the machine to unlock and start up. Thank you! But I'm noticing that no watre is going into the machine. I can hear it drain some water. It is very hot and steamy in the machine so no heater problem, but I don;t see any of the soap on the bottom of the machine rinsing away. I'm afraid its stopping because the motor is overh


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Hi the dishwasher is leaking from the back of the machine, problem is I cannot get the machine out to see or fix the problem as i cannot unscrew the rear feet and dont want to pull too vigorously as i would break the feet. Any suggestions?


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Machine does not heat up. The water remains cold and the cycle takes hours irrespective of the setting temp. Heater seems to be OK and a tech guy repleced the sensor today as he thought that was the problem after everything else seemed to checkout ok but still no go. It has already cost us 200 dollars and I dont want to keep spending money having tech guys guessing the problem. Any suggestions? Thanks


Depending on the model, I have had loads of Bosch dishwashers fail because they have blown the heater relay solder joint on the main control board. Usually just requires control board to be opened up, and the faulty solder joint re-soldered. Occasion ... Bosch Dishwashers

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

HE error My LG LD-14aw1 is showing HE error code - Heater Circuit is troubled???. (Not as much as owner!!!). I have repaired several dry solder joints in the control module, which have been causing various operating failures, but the HE problem has got me stumped. Can anyone provide me with a wiring diagram of the machine and or the control module? I'd like to trace the heater circuit to see if I can find the fault. Many thanks


From the manual: Errors: HE: Heater circuit failure.Please call your Authorized Service Center or LGECustomer Service at 1-800-243-0000(US), 1-888-542-2623(Canada). ... LG 24 in. LD-12BW5 Free-standing Dishwasher

Dishwasher sounds like it is running normally, (no grinding sounds or anything)but there doesn't appear to be any water coming into the machine. we checked to see if there was a kink in the line or if perhaps it was a plumbing problem but that does not seem to be the case. I know the circular disk in the front of the machine needs to be down and it is, so can you figure out without seeing for yourself what could be the problem and if so is it worth fixing since I can probably replace it for und


Hi there,\012Well first of all you can check out the following -Water-inlet valve - The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usua ... Dishwashers

My maytag MDBB7100AWQ stops in mid cycle at the same place all the time (for background see robert920 problems) I tested the heater continuity and found no continuity between the heater and the outer skin of the heater and the resistance of the heater was fine. Then I run the diagnostics (Automatic function tests) and its indicated Keypad 2 which is Motor -low current. I then went on to test the resistance for the motor and found out that they were all within specs (Blue to Gray 7 ohms, Bl


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Maytag MDB7100AWB Dishwasher

Kenmore Elite dishwasher Model #665 1597 2992 Machine fills with water but thereafter it neither washes nor drains. Machine will not drain when I advance the cycle by pressing the Cancel/Drain button. There was a report that there was some noise when the machine first failed. I do not hear anything when I try to run a cycle. What might the problem be? How does one turn the motor manually to see if it is bound up by something? If it is the motor do I want to pay an extra $70 to $100 and


... Dishwashers

I have an zanussi LS6 and in the display it on and off shows the A1 and B2 and spills water. The problem though is not what normally comes with A1 and B2. Somehow the water gets to electrical parts and all power is out in the café. Several experts that has been to see the machine clame it has something to do with the electrical system - that measueres when there is enough water. They say it has something to do with machine having the salt container and they have all given up repairing it. I boug


... Zanussi 24 in. LS6E Free-standing Dishwasher

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

FDW60 Hello, I have a Hotpoint FDW60 dishwasher. It seems to have the usual quality issues but the actual problem is different to most I see on here. The machine has only been used about 20 times, but yesterday the following happened, I loaded and selected intencive program, when I pressed start the machine made a shriek/chipping sound, it seemed to run for about 5 seconds then stopped with the power and prewash lights flashing erraticly for about 3 seconds then was totaly dead, no power light o


Tom,\015\012If your dishwasher is still under warranty, best thing will be to contact Hotpoint's service center for repair the problem. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Rheem classic quiet 80 it has two green light. one is indicate power on. and other is blinking 5 times and 2 second pause. then repeating this cylce like it forever. I have take the pcb out from the furnace , for seeing if there any electronic parts are burning or some cracking, but I don't see any thing unusual. this problem occured when the water heater is leacking water from the pipe then the water was spraying over the funace. because the funace is locate just one foot away from the water


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

My karcher 645 has three lights on the right side of the control panel. The bottom one that looks like a heater temprature warning light keep flashing when im using the machine. Is this normal or do i have a problem. The machine seems to be working ok.


I'm not a karcher dealer, but I'll comment. I'm assuming you've misplaced your owner's manual -- so the only way you'll know for sure is to contact karcher.com..... or a dealer. That said, I'm pretty sure your blinking light is just bells a ... Karcher Pressure Washers

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

Just looking for some advice on removing the drawer from my servis washing machine, sorry I dont know what model it is. I need to clean the powder drawer but cant find any way to remove it from the machine. There is no internal part marked push that i can see and im wondering if i need to unscrew the four screws around the drawer. Help please! Cheers


Send an email to this address asking for the user guide for your model \015\012\015\[email protected] ... Servis Dishwashers

Hi, switch underneath our miele g646sc washing machine burnt out. It is situated in a round case, with a polystyrene disc above it. The whole of this plastic case, abour 3" dianeter is clipped under the main body of the machine. Do you know what this one does so that we can try and rectify any problem that has caused the burnout, and any idea of part number or where we can see an exploded part drawing? Thanks! Steve


It is usualy caused by dampness from water in the waterproof tray. the switch is for flood protection.a miele service agent would be your best bet ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Our Asko D3112 was not draining, so we had maintenance drain the hoses to clear any blockage but it did nothing. They said it must be our pump not working. I ran one more cycle to see if things went back to normal, however now our pump won't shut off. We have to unplug the machine just to get the pump to stop. We had a repair technician come to look at the dishwasher and he says that it is a problem with the control panel/computer system. Something tells me it is a merely a loose wire and that w


Check your manual to see if you have a drain pan at the bottom of the unit, and a 'float' that checks for water collecting there. On at least some Asko models, water collecting in the pan causes the float to rise, which then changes the operation of ... Asko 24 in. D3112 Free-Standing Dishwasher

My 1998 GE dishwasher leaks. Into the floor, now I see stains on the ceiling below. What to check? Door seal is fine. The dishes get washed. Pressure is good to go. No water out of the front of machine, seems to be coming from below. Take panel off and inspect connections? How about line from sink? Is there a site with illustrations or video repair about this specific problem out there? Any help is greatly appreciated...


Check the water connection at the valve to the dishwasher. If the dishwasher only leaks when used then the motor seal is damaged. If leak is constant the the leak is at the supply to the dishwasher from the water supply at the valve\015\012 ... Dishwashers

Meile G646SC dishwasher Problem:- not cleaning very well, and could not dissolve wax stopper in dishwasher cleaning fluid bottle. We checked water temperature and was only reaching 40C even on the 65C setting. We took the side off the machine and heater element was getting power and heating up. any ideas??


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

We have a Zanussi ZIDW 956 built in dishwasher. Problem is hat it gets a short way into the program and then stops and then a light at the top is flashing ''A''. Cant see any blockage. Machine is regularly cleaned. Can you help Ben


Hi\015\012 \015\012If you have checked the drain hose and there is no blockage, and assuming that you have also checked the water inlet valve for any blockages. The issue can be with the door switch that is bad or the c ... Dishwashers

I have a Fisher and Paykel DD605i dish drawer. We have a U1 error code on the top drawer and had this same problem just over a year ago. A repair person replaced the inlet valve I believe. I am wondering if there are any tests I can put the machine through or if this is something I can fix myself to see what is causing this code.


... Fisher and Paykel DD605I Dishwasher

I have a landa hmp-4-3500 heated pressure washer and i am problems with the water heater. where can i find a trouble shooting guide for this machine


Landa does not have a model HMP so I am not sure which machine you have. If you can provide a full model and serial off of the model tag on the machine I can provide you with a digital copy of the manual you are looking for.Sincerely, ... Honda Landa PG 3500 PSI Pressure Washer

Dishwasher will not fill with water. I've already checked the float assembly, that seems to be working fine. The water just doesn't seem to run into the machine. Little history on an unrelated problem: I want to mentioned that not to long ago my brother tried to put a bunch of celery through the garbage disposal. The sinks and pipes got all clogged up and we had to take them apart to clear up. Immediately afterwards the dishwasher stopped filling with water. I don't see how the two can be r


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher ... GE 24 in. GLD5500L Built-in Dishwasher

After starting my dishwasher ADG 9340/1 (any program) and after pumping evt. (rest)water , the machine won't take fresh water in and gives an acoustic alarm ! After opening the dishwasher , I can see that the "Start"-led is blinking in sequences of six blinks . Can you give me please, a possible cause and/or solution to this problem !


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1207 seconds