Having problems with your KitchenAid 24 in. KUDP02CR Built-in Dishwasher ?

I press the Normal wash button and Start button. The dishwashed doesn't come on. Cancel light is blinking..I press "cancel" and it sounds like the washer is doing something..not sure what..then after some minutes it stops. Any ideas?


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP02CR Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I press the Normal wash button and Start button. The dishwashed doesn't come on. Cancel light is blinking..I press "cancel" and it sounds like the washer is doing something..not sure what..then after some minutes it stops. Any ideas?


... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

Hello, I have a couple year old brigs and strattion upright pressure washer. It has always ran great untill recently. It will run for a acouple minutes before dying, like it is starving for fuel. i give it a couple of minutes, it starts right back up and again dies after a couple minutes of use... I have takin the float bowl and float off and cleand the gas tank and fuel line. everything seems to be in order. Do you have any ideas what it could be? I have not tuched the top side of the carb sinc


Check the oil level in the engine itself. Verify that your oil reservoir is full, then try again.You may also want to refer to the owners manual for other trouble shooting tips. Click this link to go to your manual.http://www. ... Briggs & Stratton Gas Pressure Washer 20244

Start button pressed - Water loads and "Wash Cycle" lights are on but does not start wash. If "stop/reset" is pressed then all water is properly drained. Tried different wash cycles like "Speed Wash", etc and same problem persists. Have checked interior to make sure no blockage and that washer arm moves freely.


... GE 24 in. GSD6600G Built-In Dishwasher

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

I ran my pressure washer today in an effort to run some "stabilized" gas through it for the winter. For some reason the pump began to push oil out the top relief hole. If thats not clear, it's a feature that looks like a priming pump but is rigid. By the way, the oil appeared a bit nourish gray. Not sure if that means anything. Any ideas?


It looks as if moisture/water has contaminated the oil. Check the level of oil from the glass window. It must be high. Drain out the oil & check if water is present, if so then replace the entire oil. ... Dewalt DPD3100 Gas Pressure Washer

Im a sparky but dont work on these washer comes up with clogged filter alarm but has since been thouroughly cleaned pressure switch on diaphragm is closed not sure if should be so removed wire and still comes up in alarm would like any more ideas to try and an electrical diagram thank you


Is it giving you an error code at all? ... Dishwashers

So I found this power washer for sale. The seller claims that the washer generates a good stream of water, not just full power. He also mentions that after a few minutes the engine starts to bog down like it is working extra hard. Does this sound like a pump issue? Could something be clogged or would the pump need to be replaced? Or should I avoid this power washer?


Don't buy a power that doesn't work.There are many expensive parts on a power washer. If it was cheap and simple to fix, the seller would fix it and the washer would not be for sale.Would you buy a car that doesn't work? Especially ... Pressure Washers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

This thing is insanely loud something must be wrong! it's like a growling sound that happens every 2-3 minutes for about 3-4 minutes, I have been through the trouble shooting guide and dosen't sound like normal operation. any ideas?


Sorry to hear that you are having problems with your Dishwasher (and driving you crazy). Unfortunately, you are another victim of a common failure on some dishwashers.You are right about this is not a normal sound.The noise i ... Amana 24 in. ADB2200AW Built-In Dishwasher

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

Mi T M Model CM-1250-A/C pressure washer shuts off after 10 minutes use. Wait 5 minutes and restart by pressing On/off switch. Shuts off again in 10 minutes. Works fine while on. Thoughts on problem?


I have one of these machines and it is VERY sensitive to line voltage. Be sure not to use an extension cord or the CM1250 will shut down. If you do use an extension cord use a very heavy one. The unit uses very close to the capacity of a 15A circu ... Pressure Washers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

I have an older under the counter high temp dish washer not sure the model number but it has the three switches on the lower left, has both upper and lower wands and it is high temp. Not for sure but it seem like the homing cam switch is not working you can manually turn the came to get machine working but when it shuts off it wont restart when you close and latch the door could you please help!


The cam switch may be faulty and may be available for replacement.\015\012\015\012Hard to find replacement without model no. but for the current model it is available ... Moyer Diebel Dishwashers

My dish washer is a ADP 6836, when i press the start button, it start with 1.13 minutes after 2 minutes it automaticall foes to F4,and therefore not working at all


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

I have F&P DD603 with problem with bottom draw. Once a programme is selected and door is closed, the dishwasher beeps three times then tries to start itys cycle. It then starts but stops every 1-2 minutes (like pause botton has been pressed). If you press start again it starts for 1-2 mins then stops again. I have tried turning off the power and totally cleaned out the dishwasher but no change? Any suggestions?


Hi \015\012When you pull out the drawer, pay attention to the bottom near the bottom front panel, you will see a little tab. this tab is at both sides of the drawer, press these tabs in and pull the drawer fur ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

My kenmore ultrawash dish washer sounds like it fills with water but when it goes to the wash cycle, it only hums and no sound of water spraying. Any Ideas? It seems like I heard a loud ''click'' just before it first became silent. is something lodged in the impeller?


Either something is jammed in the impeller or you will need to replace the motor. ... Dishwashers

I have a DPH3800 Dewalt pressure washer and the soaper isn't working properly. Right tip is being used but when trigger is not pressed it puts water into the bucket. When trigger is pressed it does **** some solution into the hose but very little and very slow. The valve is opened all the way. I know my former partner used bleach in the system which I read in the manual is a no no but it did work at the end of last season. Any ideas?


How is the pump connected on a john deere 3800 psi. i took out the 4 bolts and drained the oil. pump is stuck to cam. how does it come off? ... Dewalt 3800 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1412 seconds