Having problems with your KitchenAid 24 in. KUDP02CRBS Stainless Steel Built-in Dishwasher ?

My Model is Actually the KUDP02CRBL4. It will not

\015 My Model is Actually the KUDP02CRBL4. It will not run when pushing the "normal" button or any other button. It has two lights on, the Hi-Temp Scrub, and Sani Rinse. I have pressed cancel repeatedly, the pump comes on a bit, then goes off and the lights come back on.\015

Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP02CRBS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water from my disposal backs up into my hotpoint ($300-model) dishwasher. The dishwasher works fine otherwise. Is there a one way valve in the diswasher that is suppose to prevent reverse flow and/or is there other dishwasher motor problems which could cause this. Actually the Hotpoint Model number is HDA3600N00BB but this website did not recognize that model number so I put in the closest model number closest to mine.


If it's what I think, it's a simple fix. Does your dishwasher drain run along the floor of the cabinet, then up to the disposal? (my guess is yes). There should be an "air gap" between the disposal and dishwasher, this means when it comes out of th ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Racks corroding. The dishwasher works great. Just had recall repair done. Problem is the racks are slowly corroding away and new ones cost as much as a new dishwasher. How do I find good used racks and what model racks are interchangeable? The actual model number is mdb9100aww, but it won/t let me enter the ww. Ted


Check on Ebay. I just entered this to check for you. maytag dishwasher racks" and there were several on there. One was universal and could be used with 40 different model numbers. ... Maytag MDB9100A Dishwasher

Just bought and had installed on 9/25/10, Kenmore Elite dishwasher model #665.13929K010. Start light on the front panel flashes, then runs through all lights and ends on the complete light which contnues to blink. It will not actually start the wash process at all. Before I call Sears to come out, what is the reset sequence for this model? Any other solutions you can think of?


... Dishwashers

My problem is with a Eurotech Model ED254EG timer will not continue running thru the cycle properly. i.e. In "Light Load" position the timer starts with 59 minutes but actuall runs for 2 1/2 to 3 hour


... EuroTech EDW242C Stainless Steel Built-in Dishwasher

My Model is Actually the KUDP02CRBL4. It will not


... KitchenAid 24 in. KUDP02CRBS Stainless Steel Built-in Dishwasher

Great instructions in dismantling a KitchenAid dishwasher. I followed them until after removing the screw from the sump (there were actually 2 of them in my model). Unfortunately the chopper cover would not budge! Looks like it should, but it doesn't. Don't want to try leveraging or prying too much in case I crack something and it ends up an even more costly job. Any suggestions?


Hi,\015\012 \015\012Please check the bellow link regarding your query...\015\012 \015\012 ... Dishwashers

It is actually a fagor FI 48W model. The dishwasher maintains its water giving off a smell. the manual says that it has a drain pump. SHould the unit drain after use in normal circomstances? Please advise


... Fagor FI-200 Dishwasher

We have a FGHD2433KB1 model dishwasher. Among other problems that I have seen here (detergent door not opening, dishes not clean at the end) our biggest problem is that the dishes are never dry at the end. They are actually dripping wet. It doesn't seem like it is venting during the drying cycle. Any help would be welcome. thanks


Hi,\012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried in vainto clean the things... \012Bought new spray arms online and installed them inminutes...now the thing works ... Frigidaire FDB956RB Built-in Dishwasher

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

No water flow into dishwasher. Float is not stuck. Worked fine for 10 years until yesterday. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound, only a single electronic click at start of cycle. Actual model is Kenmore Elite undercounter dishwasher 665.15982990


Hi.Try tripping the circuit breaker or disconnecting power cord for a couple of minutes. While power is off, check the inlet cable at the back of the machine.If\015\012there is no water getting into the machine, and there is n ... Kenmore 24 in. 15992 Built-in Dishwasher

Is there a general reset code for this model? Problem seems to be that it pumps out,then fills thendoesnt advance in the program.There is a clicking occasionally then it waits 5 mins then a short pump out again followed by a long pump and refil Just lacking the actual wash..+no spray


Please confirm if there is still a problem with the dishwasher. Are you expecting any further suggestions ? You should post a comment as soon as you find the torx screw driver and are able to investigate the component. ... Dishwashers

My 13 year old Frigidair dishwasher (model FDB221RFR2) is not disolving the soap tab that drops in during the later cycles. We sometimes find the soap sitting on dishes or on the bottom. It appears that there may not be enough water but I'm sure of how much there actually should be. It also appears that the soap may be dropping late but again I'm not sure of when it should normally drop. I checked the inlet value and it appears to be ok. I also checked the timer (to the best of my ability) and i


CHECK YOUR WATER TEMP, IF ITS NOT HOT ENOUGH SOAP WILL NOT DISOLVE. I HAVE ALSO SEEN INTAKE VALVES DROP OUT LATER IN CYCLE. THAT MAY BE YOUR PROBLEM. GOOD LUCK! ... Dishwashers

I have an Equator Mini Maid PLS602S dishwasher. It works fine, but the upper spray arm fell off and the clip and knob holding it in place are missing. Equator said they no longer make this model and don't have the parts. Can you tell me where to get the clip and knob to hold the upper spray arm in place. I know there is a little white clip - I actually had it but lost it, because when I tried to hold the arm in place with that, the next time I ran the dishwasher the arm fell off again. I


There are no parts sources that i can find for this dishwasher, but my suggestion to u is this, locate an appliance repair shop in the local area that has dishwasher parts, bring the portable unit down to the shop and see if they can mat ... Equator Dishwashers

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

Model SHE68P02UC/60 There does not appear to be a drying heating element in this dishwasher or did we miss connecting something up during the installation? Unsatisfactory drying on both "normal" cycle and "auto wash" cycle.Drying agent is in machine. What is "condensation drying"? Is this just blowing cool air through the machine and out through the vent? If so it is unsat. How to get the machine to actually DRY the dishes? I'm going to be very disappointed and out over $1,000.00


I am assuming you have the dishwasher connected to the hot water tap which can give water at about 40deg c (120deg F).\015\012\015\012The dishwasher uses steam from the water (after heating it further). So if the inlet water temperature i ... Bosch Dishwashers

Lower spray arm does not spin on my bosch dishwasher model number SHV55M03GB/40. However the top spray arm does spin. I have tried cleaning filters and the actual lower spray arm but found to blockages etc. many help will be greatly appreciated


S.Africa doesnt have same modles as you, but will try and help. Some washers give the operator a choice to run either the top spray arm or the bottom one independently, and/or both together.\015\012Almost certainly, there is a valve that is po ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I don't have the model number here but it is the machine with the three control buttons on the front of the door. It seems to have lost its programming. It will start and do the initial small flushing wash. The pump runs. But it never seems to do the actual washing cycle. The dishes, although wet, are not clean. Yours truly, Brian Felske email [email protected]


... Dishwashers

My Frigidaire model FDBB2040FC3 ''acts'' like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it ''running'' or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns.


... Frigidaire Dishwashers

Hello I have a Whirlepool Dishwasher model DU945PWPQ2 I have taken it apart before for maintanance but this time I am having trouble removing the ''Wash impaller'' I was able to remove the screw that sits in the middle I just cannot remove the actuall impaller it rotates and all but I just cant remember how I got it out last time .....PLEASE HELP !!!!!


LOOKUP YOUR DISHWASHER ON THE INTERNET PARTS FOR APPLIANCES AND FIND ONE WITH PARTS BREAKDOWN FOR YOUR UNIT. ... Dishwashers

My Frigidaire model FDBB2040FC3 "acts" like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it "running" or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns. We're a family of 6 so our dishwasher is pretty important in this hou


... Frigidaire Dishwashers

Lx30H actual model


I would clean the 2 back probes with emory cloth and the sump probe underneath the screen.then pour half of cup of c.l.r. (calcium,lime,rust) remover in the dishwasher and run 3 cycles.If you still have this issue let me know. ... Hobart 24 in. LXIH-3 Built-in Dishwasher

We have just installed GE Model GLDL560NSS. It fills with water and it emptys the water but it doesn't actually wash or rinse. The water just sits at the bottom of the dishwasher tub


I had the same problem running the dishwasher the second time. The first time worked perfectly. I thought the problem was from the sensor not reading enough water to actually start the wash cycle. It sure uses less than any dishwasher I've had bef ... GE Dishwashers

I have Kenmore dishwasher Model # 66517795791, and I need to remove the impeller to clean underneath the screen. When I hold the impeller and turn the screw in the center counterclockwise, it does not actually unscrew up and out.


Hi,\015\012\015\012It sounds by your description that you are going about it the correct way, but the impeller is likely spinning on the shaft, i.e. the flat spot`s on the inside of the drain impeller shaft are rounded, hence turning the ... Dishwashers

My dish washer is 4 years old and is not cleaning dishes or disolving soap. HO appears in the status window which my manuel says indicates a water heat delay. How can this water heat delay be repaired ? I couldn't find my actual dishwasher on your list. It is model FDB2810LDC1 multi speed precision direct wash system with speed clean technology.


The water heat delay indication could be caused by the fact that the heating element has failed so that the washer will not proceed with the wash program until the water is up to the correct temperature. You should be able to tell if the element is g ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have an LG Dishwasher Model LDF7810BB. I have no response at all from the control panel, no lights at all, no error messages - completely dead. The unit worked quite well for 2 years, then just quit. I have good power at junction box. I have taken the unit apart, tested the line filter box on the R of the dishwasher (actually jumped it). No response. Thoughts? Allan.


... LG 24 in. LDF7810 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0824 seconds