Having problems with your KitchenAid 24 in. KUDP02IR Dishwasher ?

CLEAN CYCLE LED ON CAN'T RESET

\015 Cannot reset from this problem. The Clean LED is on (indicated on the front panel). \015\012\015\012According to trouble shooting guide that came with the machine it could be the Thermistor (temperature sensor) or the OWI Optical Soil sensor.\015

Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP02IR Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Have a new Bosch SHE3AR52UC/07 which is not starting properly. When On button is used Auto and Sanitize LED flash (chosen cycle) but when start is pushed, Clean and Sanitized LED flash and heavy wash LED is steady and nothing happens. Tried resetting according to manual to no avail.


... Bosch Dishwashers

CLEAN CYCLE LED ON CAN'T RESET


... KitchenAid 24 in. KUDP02IR Dishwasher

Will not go through a compleate cycle and then the clean light comes on and blinks 7 steady blinks and stops the blinks again and i cant start the dishwasher unless i reset the dishwasher and then it does the same thing


Hi angelbme1,\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your problem is: will not go through a compleate cycle and then the clean light comes on and blinks 7 steady blinks and stops the blinks again and i c ... Dishwashers

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

Led indicator light is stuck on clean and won't allow a new cycle to be set


... Kenmore 24 in. 16039 Built-in Dishwasher

My frigidaire dishwasher is stuck on the clean cycle. If I unplug and start it again it will run thru the cycle. When the cycle ends it will not reset itself, and will stay only on the clean cycle. Any ideas of what it could be.


BAD TIMER ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

In order to reset my dishwasher i was told to alternatively press the clean and rinse button. my dishwasher has no button that says clean, rinse, or clean and rinse. my button choices are as follows: Front: CANCEL and START/RESUME Cycles: HEAVY DUTY, NORMAL, LIGHT/CHINA, QUICK CLEANUP, or RINSE ONLY Options: PROSCRUB, HI-TEMP SCRUB, SANI RINSE, HEAT DRY/Lock symbol, 4 HOUR DELAY. Does anyone have the correct sequence for initiating the diagnostic cycle?


If you want to reset the computer in that dishwasher you can just unplug it for a half hour. if it is a built in just locate the fuse in the or breaker that the dishwasher is on and pull it for that length of time. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Our GU2500XTPQ6 Gold quiet partner III begins a cleaning cycle but then different numbers appear on the minute countdown and the cycle never finishes. Once it gets to this point, you can only get it to drain. You cannot reset the cycle. We were once given a series of buttons to push to reset the control panel but don't know where it is. Can you help?


Yes call the manufacturer and ask for the code again ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

My miele diswasher seems to be stuck on rinse cycle and will not advance...keeps draining and refilling. Can't figure out how to reset and restart new cycle, to clear the snag. What's going on? I have cleaned all the filters in bottom of unit per operating manual. Wish I still had my GE, where you could reset the unit...no button to do that on this overpriced unit.


Sounds like a broken timer. If it's a rotary dial, they're not too bad to change.... ... Miele Slimline G832SCi Built-in Dishwasher

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

I have a FDBB2040FC3 dishwasher and the cycle doesn't complete anymore. I will start the cycle and after awhile the Hi-Temp LED and the No Heat Dry LED will start blinking and the unit stops. The dispenser does release the soap pack and the dishes seem clean but this doesn't seem normal. Thanks for your assistance Todd


Have you checked the element or the heater in you unit when the units senses that the unit is no longer heating the water the unit will stop and not progess any further into your cycle you can check this by doing a continuity test on the element to s ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a Bosch dishwasher model SHE4AP02UC/06, serial number FD901102579 that has been used twice since installation. When I select the Regular Wash cycle, the Regular Wash LED and the Active LED come on. The machine washes the dishes and then when it stops making noise. At that point the Active LED goes off and the Clean LED comes on with the Regular Wash LED. These LED's do not go off. There is no signal saying that the dishwasher is finished. Is this the way it is supposed to be operating or


Ya id say until u open the door after it has washed ... Bosch Dishwashers

Dishwasher won't reset, stays on gree-flashing light- Clean cycle


HI,This is an indication that the water did not heat properly. I have put together some instructions on what can cause this and how to reset the control so you can use the dishwasher again. Follow the link below and let me know if this he ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

''Clean'' light is blinking, ''Cancel'' does not reset the cycle.


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light flashes 7 times, all\015\012buttons are non responsive ... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi, I have a Miele G638 Plus dishwasher and the Red Inlet/Drain light comes on shortly after the wash cycle starts. I have cleaned everything out and the impellor moves freely. I have also made sure the outlet is clear. I have tried resetting and repeating on different washing cycles but it always locks out after the washing cycle starts. Could this be a heater problem as the element looks quite corroded? I have had side panels off and the water appears to flow easily through the sid


Hi\015\012\015\012Thanks for using FixYa. The first\015\012thing that should be checked is if its draining properly as it could be that\015\012the drain hose is clogged an ... Miele 24 in. G638 Plus Free-standing Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

I have a Whirlpool ADG937 dishwasher (9 years old) which will not complete a 65c wash cycle. It starts Ok and runs for a long time but then continually bleeps, when I open the door the programme indicator light is on the rinse cycle. If I reset the programme to 65c it may do the same or occasionally it will finish the cycle. I have tried salt top-up, descaling and filter cleaning all to no avail. Is the programmer faulty (can I bypass it?)or should I replace the washer?


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0902 seconds