Having problems with your KitchenAid 24 in. KUDP02IRBS Stainless Steel Built-in Dishwasher ?

Front panel does not lit

\015 Do I change the control board? how much? worh it? i have this dishwasher for 5 years\015

Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDP02IRBS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi There, I have a frigidaire FDB1502RGCO dishwasher and I have power and water going to the macine however when I turn it on it will not start its cycle. Washing light is lit and all functions are lit up as normal on the front panel however the cycle does not start. Is there a simple fix or reset for this machine or will I need to call technical support to have a technician come to look at it? Please let me know. Thank you


... Frigidaire FDB1502RGC Built-in Dishwasher

Candy csd-68-80 all four lights on front panel lit, started flashing within few seconds of switching dishwasher on, no previous problems,dishwasher not overfilled, checked manual which said too much inlet water unsure what this means or how to check it. do all usual cleaning,salt,arms etc. had dishwasher about 14 months and use it every day never had any problem before


... Candy Dishwashers

My whirlpool dishwasher is ocasionally filling back up with water, whether the door is open or closed, and regardless of of control panel being lit. It happens, then leaks out the front. If i run the cancel drain, it will pump out the water just fine. All the other cycles are working just fine, and it leaves no water at the end of of the cleaning cycle. I have found no common occurance for this


Greetings,\012\012 in most instances the water inlet valve is leaking..this is the water valve that brings water into the dishwasher...its possible, the drain water is running back into the d/w from the drain hose not installed prope ... Dishwashers

Please help the prewash and dry buttons on the front panel are continuasly lit up and the program buttons are not functioning. have turned off dishwasher from the mains , still no luck.


(WASH & DRYING) lights mean the temp is not high enough - aka means the heating element has gone requires a new one at a cost of \302\24340 for the part and \302\24390 hotpoint call out charge \015\012\015\012same has gone wrong with mine!!\015\012\0 ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

Front panel My dishwasher wouldn't drain. I read I had to remove the front panel under the door and get to the hose to look for a blockage. I screwed out two screws on the side of the dishwasher and removed the white front panel just under the door. But then there is another metal panel and I can't loosen it. Is it just stuck or is there soem way of doing this? Elmi


Did you knock out the plug on the disposal before you hooked up the drain hose ? ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a dishlex global 300 on which I removed the front cover a black wire came loose and I didn't know where it came from thanks to jyackle5 I have fixed that issue. The problem I have now is the eco light flashes and that's it (nothing else functions). I removed the front panel as the bottom door seal had blown and junk oosed behind the front panels I washed the junk out and cleaned the hole washer while I was at it the bottom of the washer (where the heating element is) over filled so I tipp


Easy fix, Use a bit of force and pull the dishwasher out.Get a few towels and tilt to the left. Water will drain out. Push back in. wait 10 mins and turn on.\015\012\015\012\015\012\015\012Regards ... Dishwashers

I am replacing the front panel on my Whirlpool dishwasher. It is a Quiet Partner III. The model #GU2455XTSS2. I need to know how to get the old front panel off? Then how to install the new panel?


Here's where you can download the service manual for whirlpool dishwasher:http://www.servicematters.com/narso/tech_ref_eng/europe/service_manuals/dish/8542%20955%2010310.pdfhope this helps. ... Dishwashers

I bought a used 001355 asko dw. the front door panel and all under panels are naturally loose and I'm having trouble figuring out the reassembly order. And then as I was trying to install the main galvanized under panel, a short galvanized sheet metal part fell out of the door inside the unit. That's the part that now has me really stumped. Can I get a picture of the front of the unit, preferrably an exploded view? Thank you. Paul Cowden. (415) 777-9858 or (415) 302-0628.


... Dishwashers

My bosch dishwasher's (model she45m) front control panel broke. When opening the door, some plastic broke and the front control panel cover came loose. I believe the latch is preventing the plas


... Bosch SHE45M06UC Built-in Dishwasher

I need to reset my Kenmore Elite dishwasher 665 16919 front panel. Drain tube was blocked and the dishwasher shut down. Now there is no power to the front panel. No circuit breakers were tripped.


... Kenmore 16919 Built-in Dishwasher

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

Sears sent me a replacement front panel #W10195641 for my dishwasher that was dented in shipping. However they forgot to include an install manual for this front panel, can you provide any assistance?


... Kenmore Dishwashers

When pressing any front button on the control panel nothing will light up or start up in any manner,does look like it did not finish draining,have water sitting in the bottom. Pulled off front access panels no signof burned wires or anything becoming disconnected? do have small childern in the house pressing buttons? power is good going to unit.??


1)check any fuse blown in board.\015\0122)check supply to the board. ... Kenmore Dishwashers

My Maytag MDB9150AWS is no longer working due to what I believe is a electrical fire in the front control panel as there was smoke coming out of the top of the front panel. There were no flames but the smell took your breath away. We had to open the Kitchen windows and door for several hours to try to get rid of the smell, but you can still smell it by the dishwasher. This model is not part of the recall. Has anyone else had a similar problem with this model?


My dishwasher (same make and model) had a similar problem except I did see some sparks coming out from th front on the side of it (on Thanksgiving Day no less - a lot of manual diswahing followed). What the problem ultimatly was is what I believe to ... Dishwashers

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

Can a front panel that is white be changed to a stainless steel front panel on a GEM quiet power 3 dishwasher. Model #GLD5900NOOWW


... GE Dishwashers

I would like to remove the panel that is on the front of my asko dishwasher and replace it with a stainless front panel


That panel is reversible. take off an see what is on the other side. a couple of screws. its easy ... Dishwashers

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Two LEDs continuously blinking on front panel. Will not reset when "cancel" button is pushed. Will not respond to any buttons pushed on front panel. What to do? Thank you.


Sound like you have a bad touch panel. replace your touch panel and this should solve your problem ... Kenmore 24 in. 15932 Built-in Dishwasher

Dishwasher GSD2030F03WWSA735136B Model Series number;Piece fell off inside front panel, making it impossible to turn on dishwasher at all..so I took off front panel screws, opened dishwasher and saw white plastic piece but can't find where it goes but it must have something to do with turning the knob to start dishwasher because the knob won't turn now..so it must attach inside somehow but I can't figure out where it goes...help!!


I think you need to get a new knob, write down the model number and make and take the pieces to your local domestic appliance supplier, there might be something similar in stock. Now I do mean the kind of small supplier that understands this kind of ... Dishwashers

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

I have a front panel with cherry wood to match my cabinets for a 1997 year Asko . Is there a dishwasher I can buy that I can use this panel on the front? Thanks


You can find dishwasher covers and panels to match almost anything at www.applianceart.com ... Asko 24 in. 1585 Built-in Dishwasher

It's showing F-1 on front panel of two drawer dishwasher. The front panel on both dishwashers is giving me the F-1's.


F1 in both drawers means the base of the dishwasher (under bottom drawer) has flooded. Not sure what procedure you used to clean the top drawer with baking soda. It is likely there was a leak through the lid seals due to over frothing which has cause ... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0612 seconds