Having problems with your KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher ?

Water not draining from tub - KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher


Answers :

HI. check the following areas for faults.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer/control board
Replace if defective (note: uncommon problem).
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water not draining from tub - KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher


HI. check the following areas for faults.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Water does not fully drain after cycle - KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher


Hi,Here is a tip that I wrote that will help you with your dishwasher ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Dishwasher won't drain. Water in bottom of tub. Washer hooked up through disposal, which was broken and just replaced. Currently, sink and disposal work fine but now tub of dishwasher won't drain. 24" stainless built in Model GLD6360L00SS


Hi\015\012\015\012\015\012Thanks for using FixYa. Hope you\015\012know that new disposals ... GE 24 in. GLD6360LSS Stainless Steel Built-in Dishwasher

Frigidaire fdb1500lsfo built in dishwasher. Have had for maybe 3 years. I push the start button, and it starts like usual, filling the tub with water. After filling, it will not do anything for about 5 mins, where then it drains. It seems to go through the whole wash cycle, but after it has pumped the water out. Dishwasher steams all of the dishes, but there is no water in it to wash them with.


... Frigidaire FDB1502RG Built-in Dishwasher

I have a DU8000XX6 series Kenmore dishwasher that won't drain the water properly. There is about a half inch of water in the tub and the float is raised (not sitting on tub bottom). When I lift up the float a little more I can hear the float switch make. I would assume that when the water is high enough the float switch makes and energizes a solenoid valve in the drain to drain the water, but shouldn't it stay open until all the water drains? Lifting the float while the dishwasher is off wo


... Kenmore 24 in. 15142 Built-in Dishwasher

Remove dishwasher drain pump - KitchenAid Superba Series KUDE60FX 24" Tall Tub Built-In EQ Dishwasher Sati


... KitchenAid Superba Series KUDE60FX 24" Tall Tub Built-In EQ Dishwasher Sati

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

Water is not coming out of upper spray arms - KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher


Remove lower basket completly put a bag around the arm that goes to the back of the machine (this will stop water going to the lower arm. Put the lower basket back into the machine and set the rinse cycle, this should clear the blockage if it does n ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Water not draining at end of cycle - KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher


... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Won't drain - KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher


If the water doesn't drain from your dishwasher, check these:\015\012\015\012 \015\012 Drain line/air gap\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Leaking water from bottom - KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\0120955r76is ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Water is not draining form dishwater - KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain out ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Water would drain - KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Why won't water drain from tub? - Frigidaire 24 in. FDB635RF Built-in Dishwasher


HI. check the following areas for faults.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking i ... Frigidaire 24 in. FDB635RF Built-in Dishwasher

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

I have a Kenmore dishwasher, model 665.17019401 (serial number FS1002610). It goes through all cycles, drains out water, periodically, and dries the dishesat the end. But, when it ends, there is water at the bottom of the tub, at least 1 quart of water. I have to drain out the remaining water in the dishwasher. What is wrong?


Either the drain or screen is somewhat plugged, or a clog or jam in water pump. Many machines do leave just a little bit of water just so the sewer fumes don't come up. ... Kenmore Dishwashers

I need to winterize the built-in Kenmore dishwasher in a mountain cabin where winter temperatures will drop below freezing. The unit is at least 10-15 years old, but I don't have the model number handy. My approach to the cabin water pipes in general will be to gravity-drain them and then blow out remaining water by adding and releasing air pressure. RV antifreeze will go into all P-traps. When it comes to the dishwasher, my plan is to remove the drain hose from the P-trap and drain it as mu


In order to get the water out the best thing to use is a wet dry shop vac and attch it to the end of the drain hose on either your dishwasher or clothes washer this will remove any water in the drain pumps.As far as RV anti freeze being added not sur ... Kenmore Dishwashers

Dishwasher won't drain. Pushed the drain button and water stil is at bottom of tub. Sink is not clogged, drain hose is not clogged and can't see what is in bottom of tub due to standing water? What are suggestions for repair?


... Kenmore 15639 Built-in Dishwasher

I own a build-in LG Stainless Dishwasher (modle: LDF1178ST). It stopped draining water during its recent startup due to its idle (no operation) for about a year:). I can only feel the hose full of water by touching the drain hose between the washer and the sink desposal. It's hard to check other part of dish washer since it's built in our cabinet. Could any dishwasher expert help to advise how to trouble shoot or fix this problem. Thanks, Alex Chen 571-220-7484


There is a float in the bottom of the dishwasher that tell the motor to turn on and pump out the water. I would check the float first to see if it is hung up and not raising to tell the dishwasher that there is water in the base. Check the check valv ... LG Dishwashers

When we do not use the dishwasher for a week or more water seems to back up into the tub. The water has a foul smell to it and can be as much as an inch or so deep. The dishwasher drain hose is attached to an insinkerator disposal. By the way this dishwasher is only a couple of months old and we have had to have it serviced three times. No one has been able to explain the water accumulation and it can not be demonstrated unless the washer sits unused for a while.


... KitchenAid KUDS40CVSS Builtin Dishwasher

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!


... GE GSD5130 Dishwasher

Sometimes the dishwasher drains, sometimes it doesn't; I emptied the dishwasher, removed the bottom tray and baskets; ran a cycle - it drained so, I presumed it was now operating as it should - it wasn't - the tub was full of water so, I ran a rinse (5 minutes) cycle - it drained next time I ran a cycle - it didn't drain


Hi,Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain out ... GE Nautilus 24" Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2423 seconds