Having problems with your KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher ?

There is alot of "crud" left on the top rack dishes. i have cleaned the dishwasher and replaced the hose that goes from the back of the machine to the top rack to the top spray arm - still have problems


Answers :

Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works like new... However I have also found that if theheating element goes bad then that also can mess things up bad... So I wouldbuy new spray arms, and also check out the heating element to make sure it isworking... Here is a tip that will help you with the online buying...
Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and seehowsimple it was. thanks Ronnie " - ronnieshomes
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There is alot of "crud" left on the top rack dishes. i have cleaned the dishwasher and replaced the hose that goes from the back of the machine to the top rack to the top spray arm - still have problems


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

My Frigidaire FDB935RHS0 top rack is not getting enough water (pressure) to rotate the top rack sprayer. We have looked at all the connections under the machine as well as the tubing, but we have not found any obstructions or problems. The water moves very slowly up the tube to the top of the machine and the water only seems to trickle out of the feed line therefore the sprayer doesn't spin or spray. We have disassembled the bottom sprayer and have found no obstructions there either. Do you have


... Frigidaire 24 in. GLD2350RC Energy Star® Built-in Dishwasher

Bosch srs43c12gb/14 classixx dishwasher spray arms not spinning. The dishwasher goes through normal cycle but the spray arms are not spinning, I have cleaned them and the filter inside the machine and the one on the water hose, still not spinning. the machine is about 4 years old.


... Bosch Dishwashers

When my Kenmore 665 dishwasher is done with the cycle, the glasses on the outer areas of the top rack have stuff stuck to them. Almost like the jet spray is clogged and spraying the garbage. My "repairman" has taken apart and cleaned everything he could. The problem was solved for a few washes, but then the particles continued to come back. Any suggestion>


... Kenmore 15129 Built-in Dishwasher

- the dishes and glassware on the top rack are not coming out clean - I checked the course strainer to see if it is being blocked but don't see any thing there - I also took out the spray arm that sprays up into the top rack and ran water through it with a hose - it also appears to be free of clogs. - I don't see the spray arm spinning when I open the door during the wash cycle - - lastly, it may be unrelated, but the dishes are not coming out of the washer as hot as they used to be any i


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

The top rack isn't getting clean. Could this be a pressure problem our an internal problem? It's not whishing like it used to. The water isn't reaching into the glasses. I think the only water getting to the top rack is what is sprayed onto the bottom rack dishes.


My husband told me to call a repair man rather then going through FixYa.Please take me off your mailing. Thank You ... Whirlpool Dishwashers

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

I have a bosch SGV43A03GB/42 dishwasher. The cups / plates were coming out dirty so I did all the drain cleaning and ran finish dishwaher cleaning fluid. What I noticed was the top arm wasn't rotating and the source of the problem. I took out the arms and cleaned the holes to ensure no blockages but still a problem. I bypassed the door switch and found that theer was no water being pumped out to the pipe that leads to the top rack. I opened the two torx screws and looked beneath pipe to find wha


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SGV43A03 Built-In Dishwasher

I have a Bosch SHU9955UC/14 dishwasher. I am having problems with the top rack not cleaning. The dishes on the bottom rack are cleaning just fine. I have taken the rotating spray arm off and cleaned it out and replaced it. I have also taken all of the filters out of the bottom of the unit and cleaned them. Any other suggestions for fixing this problem?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch SHU9955UC Built-in Dishwasher

Mod # KUDL03IVWHO, SN# fyo109574 We purchased this in FeB 2009. Dont know if itis still under warrenty or not. Problem is the top arm is not spining so no top rack dishes are getting cleaned. Is there anything I can check or do to solve the problem


... KitchenAid KUDC03IVWH Builtin Dishwasher

Hello! My 3 yr old Bosch dishwasher (I think it is a SHE 43) is doing two things: 1) leaving a serious white film on dishes and glasses 2) leaving grit inside glasses on the top rack (always on glasses placed on the far back right of the top rack) I've tried cleaning the machine with hot washes with no dishes, vinegar only, but no luck. Any thoughts? Many thanks for your help!


Hello. Since you have already cleansed the interior of your dishwasher, we must conclude that the problem is with the water itself. If you do not have a filter on your water, you may want to consider installing a dirt/rust filter, at least on the h ... Dishwashers

My whirlpool dishwasher is not washing the dishes properly. when finished cycle, I still see the dishwasher tablet half used. The grey long piece at the back, seems to have come out of the two holes it fits into on the "floor" of the inside of the machine. I've clicked it back into place, but it still pops out. Sometimes the rotating sprayer at the top and bottom, don't move either when its out of place. please help.


... Whirlpool GU2400XTP Built-in Dishwasher

I have a moffat dishwasher MSD 2000 p00ww I checked the drain hose, ran water trough it had no problem, hooked it back on to the dish washer. I blew into the hose an could see the the air bubbles no problem in the dishwasher. But it still won't drain. Just wondering if you could hep me, on what to try next. Your help would be great.


... Dishwashers

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

I have a Maytag model DWU9502AAM dishwasher, took out the top rack (easy) to wash furnance filters, and cannot get the rack back in rightly! Where are the rollers on each side supposed to be placed to hold the rack? Do the snap supports face up or down on the rack? I broke two of the roller snaps and replaced them, still no luck. Does anyone have a schematic??? Maytag has nothing on this I can find. Thanks!


Hi there,\012Well you can try from upside face...... there are some plastic lock type grips... for more information you can download the repair manual, please follow the below link -http://cgi.ebay.com/_W0QQcmdZViewItemQQitemZ ... Bosch SHU9915UC Dishwasher

Hi, my hotpoint aquarius df61 makes all the noises of washing, i hear the water going in, motor is running, however i dont believe the spray arms are revolving, so the dishes are not getting clean. i have cleaned the individual holes in the spray arms, but i don't think the water is getting up the back pipe and into the top spray arm. it does not spin at all. no problems draining. help please. and were can i get a copy of the user guide, free preferably. thanks


How old is your machine? it is posible to have something in the watwr pump, you hear the water and the motor, but the fan of the pump (washing pump) is blocket. also the pipes hat make connection to the water pump and the arms. at someoane i found gl ... Dishwashers

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Spray arm, 3rd level, fell off. Flower-like looking ring is still attached to top of dishwasher and arm itself is no longer attached. How can I reattach the spray arm to the flower-looking like ring?I have Frigidaire model number PLD4555FRC0; part # of spray arm, 3rd level, grey is 154478202. I called help line and got someone whose accent I could not understand. I think his name was Victor. He left the line and never came back but, before he left, he said he was looking for the part...why he, t


Unscrew the flower looking piece, there is a white plastic retaining clip inside- press it back together. ... Frigidaire PLD4555RFC Dishwasher

Bosch SKT5102 The machine wont stay on. When I push the on/off switch the machine comes on for a split second then goes off. If I hold the switch in then the machine works. I have taken the back off and located the micro switch and note that I can buy a replacement. Do you think that is the problem and will I just be wastin my money on a new switch if not. Thanks


It sounds like the switch but you don't need the bosch one if it is only the micro-switch they are easily available\015\012ger531 ... Bosch 22 in. SKT5002GB Built-In Dishwasher

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

We have a 2500 6.5 briggs & stratton pressure washer. Was working great, changed hydrants & hoses. Now it won't spray water. Yes we went back to the orignial hose & hydrant. Still won't work. Got any suggestions?


... Briggs & Stratton 3000 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1234 seconds