Having problems with your KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher ?

My kitchenaid dishwasher leaves a white residue on clean dishes. 4 year old appliance, worked great until 6 months ago. under warranty, service repairman said i was using too much soap( am not). he cleaned it with salt and vinegar stating i had lots of suds when he ran a rinse cycle. i always use jet dry and don't use the heat drying cycle. it didn't improve. i tried different soaps, more vinegar, and finally bought a special product to clean the dishwasher. the inside is stainless steel, very c


Answers :

Hi,

The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

DishwasherResidue and Film on Dishes

heatman101
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kitchenaid dishwasher leaves a white residue on clean dishes. 4 year old appliance, worked great until 6 months ago. under warranty, service repairman said i was using too much soap( am not). he cleaned it with salt and vinegar stating i had lots of suds when he ran a rinse cycle. i always use jet dry and don't use the heat drying cycle. it didn't improve. i tried different soaps, more vinegar, and finally bought a special product to clean the dishwasher. the inside is stainless steel, very c


Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

I have Jenn-Air dishwasher that I use the heated dry cycle for. Last night at 11:00 pm or so I ran the unit. Today at 10:00am when I opened the door steam barrelled out and everything was so hot to the touch I gave myself a significant burn when grabbing a non-metal item in the dishwasher. Should I be concerned there is a problem with the entire unit or just the heated dry cycle? Should I be concerned about fire danger due to a short?


... Jenn-Air 24 in. JDB2100AW Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Dishwasher bubbles I have a kenmore elite mod- 16599201 stock # 16599 , recently there has been bubbles in the washer after the wash cycle ends . I thought that I might of put detergent in the jet dry hole so I removed the dispenser and rinsed the whole thing completely clean and reinstalled it. but the bubbles are still there . I think its the jet dry not completely rinsing away. I cleaned the dishwasher with vinegar and then glisten. My water temp is slightly low as I have my water heater set


... Dishwashers

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

Dishwasher Odor Our dishwasher leaves dishes and glassware with a sulfer odor after the wash cycle. We have run vinegar through it, use jet dry, and use 1 tablespoon of dry detergent. All suggestions made by the "customer support". None of these have led to a permanent solution. We're about ready to "kick this to the curb". Any suggestions? I've checked filters and there doesn't appear to be any standing water. We have city water and there isn't an odor when you drink it.


I would disconnect the drain hose from the sink trap and drain the water out into a pot -- just to make sure there's nothing in the hose that can't get out. Check the sink trap too to make sure it's not holding something. Run an empty dishwasher us ... Asko 24 in. D3250 Built-in Dishwasher

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

I own a GE Profile Built-in Dishwasher Model number is PDW7880G00SS, Serial number is FF7872828.  We have recently been having major cleaning issues with it, especially the top shelf i.e. the glasses.  There is always dried up debris on them.  We always run the water hot and run it on "added heat" cycle.  I was wondering if there is a filter, or an area in the dishwasher that needs to be cleaned out?  Even if I put perfectly clean dishes in there, they will come out dirty, which leads me to thin


... GE 24 in. Profile PDW7880G Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Brand new Quiet Partner III. Doesn't clean the dishes, has milky residue on walls, silverware not clean, leaves spots on glassware, not even the inside door gets clean! I use liquid soap (1tbsp), Jet Dri, don't overload, shut off Heated Dry, have tried all the cycles HELP!! Marcia


... Whirlpool Dishwashers

Dishwasher runs full cycle, however, the dishes and glasses have small particles of food dried on them when done. I do rinse all plates and utensils before turning on. I run on a normal cycle, no heat dry. I use cascade action paccs 4X concentrate. Which appears to not disolve completey, the packet. It normally does. There is no water back-up in sink, and I also open the trap ,no blockage. Please help, Dan


Hi Dan and welcome to FixYa, I am Kelly \015\012\015\012 Most of the time when you start having dirty dishes post wash there is either an internal blocked screen under the lower wash arm tower or a problem with the drain. ... Dishwashers

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

Our dishes smell like vomit after they have dried. We run them through the dishwasher, they seem to smell okay. Then when Dry, the smell returns. We have tried vinegar and tang rinses to no avail. We have turned up the heat of our water to scalding, that hasn't helped. We have disconnected drain hose and there is no smell there. What can we do to get rid of this awful smell? There is no food in any filters, heating element is clean except for some hard water stains. We have a whirlpool 575-0 qu


... Whirlpool Dishwashers

Heated drying cycle on Kitchen Aid (12 yrs) not drying upper row glasses. Also there is significant spotting. Is there a way to thoughly clean the machine from years of use. It works fine otherwise through all cycles.


The best way to clean it out is to run a empty load with a coffee cup full of vinager on the top rack, you might need to do this a few times to get all the gunk out. As fas as the drying goes check you heating element at the bottom of the tank and lo ... KitchenAid Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

Clean light blinks 7 times after going through complete cycle up to heated dry. ive reset it using the heated dry/normal wash buttons. so it will run until it has to dry then i get the error. how do i fix?


This error says that there is a fault in the heater circuit. the heater circiut goes thru the doorlock assembly, thermostat(if equipped) then heater and back to the board.\015\012\015\012do you see or feel and rough spots on the surface ... Kenmore 24 in. 17014 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2225 seconds