Having problems with your KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher ?

My kitchen aid dishwasher model # kudpo1flss3 stopped near the end of a cycle and now it is not responding or indicating power at the control panel. It has a little bit of water left in the tub but must have been close to completion as the dishes were clean. The breaker is on & there is power up to the connection @ the appliance. Almost acts like a main fuse is blown or something....


Answers :

You will need to have the mains plug removed and the power cord traced up to the control panel which is the main program controller unit. It seems that the program controller has failed and if so the fuse would have blown with a reason most often with a failure in the circuit. you need to check the control panel with a multimeter to confirm the position of the supply. If there is supply without any response then the controller has failed .
\015\012remove the motor line and see if the voltage builds up , look for any blown components or observe of there is any burning smell on the motor, controller or the valves- input and drain.
\015\012It will be best to check the cost of a new controller unit and confirm.

Hi
\015\012\015\012

The water did not drain\015\012completely so it stopped. Dishwasher not draining issue usually occurs due to\015\012kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for\015\012any visible clogging, remove if present. If no visible lint is present then\015\012remove then turn off the dishwasher and remove the drain hose and check for any\015\012visible clogging. If still not visible then the drain filters or drain pump is\015\012clogged and you'll need to clean the drain filter and drain pump. Also, check\015\012for any food pieces stuck near the pump impeller. Please note that dishwashers\015\012don't drain out the complete water such that heating element doesn't overheat.\015\012Also check this video for details---
\015\012


\015\012

Hope this helps...please post\015\012back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kitchen aid dishwasher model # kudpo1flss3 stopped near the end of a cycle and now it is not responding or indicating power at the control panel. It has a little bit of water left in the tub but must have been close to completion as the dishes were clean. The breaker is on & there is power up to the connection @ the appliance. Almost acts like a main fuse is blown or something....


You will need to have the mains plug removed and the power cord traced up to the control panel which is the main program controller unit. It seems that the program controller has failed and if so the fuse would have blown with a reason m ... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Kitchen circut was accidently turned off. Now whirlpool gold disher will not work(unit was not running and the door was not closed all the way when circuit was turned off, All circuit breakers are on) There are no lights on display when door is closed completely, and it appears to have no power. Worked fine prior, what could it be? The unit has not been removed from under the counter yet. Is there a fuse or circuit breaker on the unit? If so where is it located? Other troubleshooting ideas


Hello- Turn power off. Remove kick panel and cover for power wires. Check connections. If these are ok, most likely suspect is a fuse at the control. This is a little harder to get to. Remove inside door panel screws. Unplug wires and remove panel. F ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

I have a GE Quiet Power 1, dishwasher. Model #GLD4200L00WW, Serial # TH837317B. It only has 1 soap dish with lid, no open dish for 1st wash?? Do I put only soap in the closed soap dish or do I put a scoop in the bottom of the washer and a scoop in the closed dish??? Thank you for your time.


... Maytag Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My dishwasher stopped cleaning my dishes when it was just under 2 years old. I hadn't changed the type of detergent, or how I loaded/ran it. We have since tried different detergents and different wash cycles to no avail. If I want to use the dishwasher, I must first completely rinse off any food--and I cannot load dishes as tightly as I used to be able to. Yesterday I noticed that a dish in the back left corner--bottom rack was completely untouched---the residue was as if I had put it in the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU3600XTV Dishwasher

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

MDB6709AWW1 Poor Quality Control Panel Our dish washer is 2 years old this month and the control panel broke!!! My service technician told me that he has seen DOZENS of new Maytag dishwasher control service panels break and is convinced it is a design flaw. When I called Maytag the customer service rep had the NERVE to tell me "that because the house is near the beach, I must get a lot of power outages and power surges, that is why the control panel broke." I told her I wasn't born yesterday


... Maytag Dishwashers

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

No power to dishwasher and checked power breaker already it seams to be ok. I think its the door switch. I closed the door to hard one day so I wonder if it did something to it.


\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012\015\012Is there power getting to the dishwasher? This ca ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a TDX6 Technika dishwasher. When I run it on 5 cycle it contiues to heat until you turn off the power. The drying cylcle must continue on and if you leave it on for a few hours the dishes a too hot to pick up, You have to leave the door open foe a hour to be able to pick up the dishes


... Dishwashers

8575637 Brand new dishwasher installed about a month ago. Its been used about 10 times and in the middle of a wash cycle, completely stopped with no power. Have checked the plug, outlets, breakers. Cannot get any of the buttons to light up, have checked to make sure it wasn't locked out - no power at all. Manual is not helpful. Any ideas?


... Whirlpool GU2400XTP Built-in Dishwasher

My ge nautilus roll away dish washer and just stopped running. no breakers were tripped. I t just stopped like has no power. Does have breaker built into it? it is about 4 or 5 years old


... GE Dishwashers

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

I have a GE quiet power 3. model ghda480noob The dishes are not even close to being clean and the dishes have a heavy soap deposit.


Hi\015\012\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's sp ... Dishwashers

Power went off when power was restored my dishwasher was peeping and would not go on. I closed circuit breaker for one minute restored it dishwasher still not working. peeping


This happens and it is our bad luck!During sudden power failures and restoration, some times the electronics go faulty. You have to check the main electronic control board. ... Dishwashers

Liquid dish soap was put into the rinse aid dispenser ...does the rinse aid dispenser close off completly (i never use it anyhow) so i can just forget about it? kitchenaid dishwasher model # KUDIO1IL   if i can't close it off, how do i drain it?


... Dishwashers

I'm getting a PF power interupt code. When I press the "Start/Cancel" button the code goes away. Unfortunatly the unit will not power up. It appears to be completely dead. If I cycle the breaker the PF code comes back and we start the process again. What's wrong, help!! Bob


Hi,If pressing the cancel button doesn't get rid of the power failure error\015\012 "PF" then you have a bad control board. So you will need to replace \015\012the control board itself.You could try to disconnect the power su ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a Kitchenaid Dishwasher about 5 years old. It has completely stopped working no lights power nothing. Water standing in the bottom. We have flipped the breaker but it doesn't seem to be an electrical issue at the breaker.


Removed power line from panel board # 11 as seen in appliance parts pros and shocked the board. It came to life and completed a cycle nominally. Then it died again. Tried to shock it again and sometimes it works but most times it doesn/t. Similar ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

I have Miele g665 dish washer and there is no power when you turn it on. I have checked the power point and it is on. The door is closed. The manual is saying the circuit is blown. Does anyone know how to replace one.


Call Miele Technical Support at 800.999.1360. They can help you resolve your problem. ... Dishwashers

Wont start I've had the washer for many years with minimal problem. Yesterday when I closed the door no light went on and the washer would not start.  After 20 minutes or so it suddenly went on and worked fine.  I thought that it might have not completed its last cycle. Today, however, I had the same problem and it's been over an hour and still hasn't started. (I checked the circuit breaker and it's fine)


Give it a firm push over the door latch once you've closed the door..it might be the door switch not activating. oops.... first and formost isolate from power for 5-10mins and try ... Bosch 24 in. SHU43 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1376 seconds