Having problems with your KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher ?

Kitchenaid KUDE60 FVWHO clean light is flashing code 6-1

\015 The clip holding the hose from wash motor went off and had a water spill. I replace the hose with new clamp and now it does not start and the clean light is flashing 6-1\015

Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kitchenaid KUDE60 FVWHO clean light is flashing code 6-1


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

My kudpo1ilbt6 kitchenaid dishwasher clean light flashes 7 times, then pauses, then repeats. Cannot break out of this mode and get dishwasher to start. Reset circuit breaker also. Is this a diagnostic code? How to put controller into diagnotic mode?


... KitchenAid Dishwashers

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers

I have kenmore quietguard 3; model 665-17022401. The clean light flashes at the end of every wash. The codes work to reset the light, but it reappears after every wash and the dishes are not clean. Any thoughts?


... Dishwashers

Kitchenaid kudc03fvss0 dishwasher stopped mid cycle without drying dishes last week and then stopped altogether with lights flashing and full basin. I disassembled filter/pump cover in bottom and cleared several plastic pieces and cleaned chopping blade and screen. After unplugging/plugging and pressing cancel button the pump runs for about 10 seconds and stops with normal and heavy duty lights flashing. What should I check next?


... Dishwashers

I have a Frigidaire dishwasher (FDB2810LDC1) and a Er code appears in the display with the sensing, rinsing agent low, sanitized, and clean lights all flashing as is the child lock light. After seeing the Er code, I opened the dishwasher and thought I heard the detergent tray open but most of the detergent was gone with a little remaining. This has happened before and we have had the electronic panel replaced twice. Could it be something else like something blocking the detergent tray from op


... Frigidaire Dishwashers

I have a frididaire proffesional series aquasurge with speed clean dishwasher # PLD4375RFC3 dishwasher there is an Er code that just keeps flashing the china/crystal light is flashing as well as the low rinse light. it used to sound like it was running when you would close the door but nothing was happening inside. any ideas?


... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Kitchenaid dishwasher beepand and clean light flashing


... Dishwashers

ER Code Flashing. Frigidaire FDBB4365FC3 about 3 yrs old. Flashing lights on display. have reset the breaker multiple times. Got it to wash again but stops about midway with ER on display as well as Washing, Drying, Clean S flashing. Guy C.


... Frigidaire Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

KitchenAid stainless steel built in - flashing "Clean" light


... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Our MDB7100AWQ flashes the light that the troubleshooting sheet says means: "Turbidity sensor fails to find clean water" I cleaned a lot of gunk out of the screens but the code didn't change. Do turbidity sensors get clogged up?


Yes, depending on how it is mounted, ther could be gunk in the stub of pipe or a film caused by hard water on the sensor, pull the sensor and clean. ... Maytag MDB7100AWB Dishwasher

My clean light is flashing and the lock light is on, on my whirlpool dishwasher. I've tried the reset code of HD/N/HD/N and it didn't work! What can I do?


What is the model? If you take the panel off you can test the control board and controller by unhooking the ribbon cable from the controller to the keyboard. Then close the door. If the pump comes on, it is the control panel, if the pump does not co ... Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

I ran the test cycle on my Bosch SHU9915UC/006. The regular wash light and quick clean light are flashing. What is this diagnostic code?


... Bosch SHU9915UC Dishwasher

We have a kitchenaid dishwasher model#kud102irbl serial#FU1705420 Clean light keeps flashing on 7 times, waits a few seconds and flashes 7 times again. How can we repair this?? Dishwasher will not leave this mode. WE can not use it at this time.


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

2006 kenmore elite dishwasher 665-17263402- the clean light flashes 7 times , pauses then flashes again 7 times. What does that code mean? Cannot get washer to operate.


The blinking "clean light" is a common problem with some of the Kenmore and Whirlpool models dishwashers. The problem is usually attributed to water supply temperatures being too low when filling. Apparently, there are some issues with th ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

Kitchenaid kudso1dlss3 clean light flashing cannot do a new cycle


I do not have the same model as you, my model is KUD01ILBS6 but I have the same problem. A service tech told me it was a error code and here is how to fix it.\015\012\015\0121 open the dishwasher door\015\0122 hit high temp scrub ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).To resolve this you will have to reset the console. Do this by closing ... Whirlpool GU2400XTP Built-in Dishwasher

I have a kitchenaid dishwasher and the clean light keeps flashing and will not clear any idea?


Turn circuit breaker off for 10-15 seconds...then back on...then see. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1499 seconds