Having problems with your KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher ?

The dishwasher will not operate. Some of the blue indicator lights on the control panel are blinking, and I can not get them to stop, by using the Cancel button. Is ther a reset somewhere on the machine?


Answers :

Turn off the power at the fuse or circuit breaker for one minute.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The dishwasher will not operate. Some of the blue indicator lights on the control panel are blinking, and I can not get them to stop, by using the Cancel button. Is ther a reset somewhere on the machine?


Turn off the power at the fuse or circuit breaker for one minute. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Hi, Dishwasher problem: When a programme starts, the machine fills with water then stops and the "check water" light comes on. To empty the machine, I used the reset programme which does empty the machine. Any ideas of about what might be causing and the solution to this? Many thanks, Richard


You will need to check the inlet valve and the water level pressure switch. It can also be a low pressure in the pump that is giving out the signal for the control board to shut off.\012So first of all check the water line throughly to confirm. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's


... Kenmore 13719 / 13712 Built-in Dishwasher

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a maytag dishwasher (model # dwu491oaax - not sure if the 4th lettr from end is a "zero" or letter). It has never been a problem before, but hadn't been used in awhile. The light in the front is not on, and when I close the door and turn the knob, it makes the same "clicking" noise it used to, but the machine does not come on. Any ideas? is there a reset button somewhere?


... Maytag Dishwashers

Hoover HED 6612/1-80 dishwasher all four lights flash and beep whilst the machine drains, after a couple of minutes the beeping stops but the four lights glow. Cannot reset to cancel. Also still makes draining noise whilst the door is opened. There is no water at the bottom of the machine


Not sure if you have got a user manual for this dishwasher. You can download one from this site.\015\012\015\012You have a flood situation ... Hoover Dishwashers

Hoover HEDS 668 dishwasher all four lights flash and beep whilst the machine drains, after a couple of minutes the beeping stops but the four lights glow. Cannot reset to cancel. Also still makes draining noise whilst the door is opened. There is no water at the bottom of the machine.


... Dishwashers

Just purchased an Omega DW501WA dishwasher and after the 2nd use it stopped and the the 2n light from the right is flickering and the machine does not continue its cycle. The water is still remaining at the bottom and is not pumped out. Have tried to reset several time with the reset button on the front panel, but to now avail. Please advise of any possible solution. Thanks


I am having the same issues... ... Dishwashers

Hoover HEDS 668 dishwasher all four lights flash and beep whilst the machine drains, after a couple of minutes the beeping stops but the four lights glow. Cannot reset to cancel. Also still makes draining noise whilst the door is opened. There is no water at the bottom of the machine.


... Dishwashers

I just bought a used Excell XR2600 pressure washer and it stopped working after the first half hour. It seems like it has not fuel, switch it does. is there a fuel on off valve on the machine somewhere that I can't find? Thanks Ed


... Karcher 2500 PSI Pressure Washer

Bosch she44c06 will not stop draining, what is key selection to reset and continue using machine


On mine I have to push 2 buttons at the same time for 3 seconds to cancel cycle.Check your manual under cancel cycle. However you may have a problem discussed at this link:\015\012 ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

My Miele dishwasher (G 856 SC) is about 9 years old and has begun stopping in the washing cycle. The pump still drains the water when I reset but it no longer finishes the wash. Any ideas other than to replace the machine! I have tried restarting and cleaning the bottom large filter (both of which used to work) Thanks


... Miele G892SC SS Dishwasher

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

We have a Katcher HDS 3.5/30-4 M Ea. Was using it, stopped using it briefly in the middle of a job, pulled trigger again, and there was a lack of pressure. Went to the machine to troubleshoot. The "engine indicator light" is on. Checked the temperature of machine: fine. Water intake: fine. We have not been running it at high temperatures, but about 50 degrees C. The pressure was at about 2300 PSI before it stopped. Any ideas?


... Karcher Pressure Washers

My kenmore elite model # 253.4448370 keeps beeping and won't stop. We try to press reset button because high temp and power failure lights are flashing but when we press reset button it doesn't seem like the button works..it doesn't reset like it use to...does anyone know how to make this beeping stop? It appears that the temps are right for both frig and feezer but beeping won't stop...HELP!!


... Kenmore Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

Continuous rinsing My son used a large quantity of washing up liquid instead of dishwasher powder and now the machine will not stop rinsing and is still full of bubbles. What can I use to nutrelise the soap and stop the rinsing?


Put 2 tablespoons of oil into the water at the bottom of the dishwasher it will help break up the suds. Sprinkle as well ordinary table salt liberally across the suds to disperse them. Try to drain the unit as much as possible, soaking up any residua ... Hotpoint 23 in. BF41 Built-in Dishwasher

Quiet Partner II Whirlpool Dishwasher 2 years old, used about 6 times in 2 years. Panel LED's flashing like a Christmas tree: Pots / Normal / Sani / Cancel lights all flashing Tried different resets as found on web but none work. Dishwasher was NOT being used when the flashing started. Need reset sequence if there is one.


Unusual LED or\015\012Display Readouts\015\012Open ID diodes and/or LED\015\012circuit(s) in keypad, or open\015\012ci ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

After starting dishwasher to do a normal wash with heated dry, the dishwasher stops and Clean light blinks 7 times, pauses and this continues until I reset the machine. After reset it goes to rinse only and goes for a minute or so and stops.


Hi\015\012\015\012Please check if the clean light is blinking 7 times. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To reso ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1362 seconds