Having problems with your KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher ?

I have a blinking light china button and it will not run


Answers :

Hi,

Kindly provide few more details :-

1. Is there any sequence of blinking?
2. Kindly explain - any other lights blinking ....?

Let me know,so that we could proceed.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a blinking light china button and it will not run


Hi,Kindly provide few more details :-1. Is there any sequence of blinking?2. Kindly explain - any other lights blinking ....?Let me know,so that we could proceed.Hope i helped you.Than ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

My kenmore dishwasher, model 15822, just stopped working. The quick rinse light is blinking. The only other buttons that work are the pots & pans light which blinks when pushed, and the cancel button which will run through the 2 minute cancel cycle.


These are known to develop sticky switch contact pads. They stick in the contacted position and stifle the panel. Sometimes heat can be applied with a hair dryer to release them and make the unit function again. This is more than likely a temporary f ... Kenmore Dishwashers

Was running a wash cycle lastnight and it stopped running and the clean (green) light is blinking and won't turn off. When I push the Start button, there is a red blinking light. Help. It is a Kenmore Stock # 16033 Type 575-0 and Model 665.16033401.


Is your washer a front load? Does it have a small window where you read the stages or minutes left?\015\012If so is there a code flashing in thet window?\015\012Also what year is your model? ... Kenmore Dishwashers

Clean light blinks 7 times pauses 1 second and repeats. will not work. the light above the clean cycle indicator blinks 7 times. I can not run the dishwasher, When I press start the light above the start button blinks and will not start


Hi there,\012Well first of all you reset this by pressing - High Temp Wash, Heated Dry, High Temp Wash, Heated Dry, High Temp Wash.If you don't have a heated dry then use "air dry"This sequence help you to reseting the e ... Whirlpool GU2400XTP Built-in Dishwasher

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Clean light is blinking, have already killed the power, then called to whirlpool and they walked me through resetting it by pushing buttons, however when i attempted to run it after resetting it, it started to run then went right back to the flashing clean light. i tried resetting it again, and ended up with the same result.


You may a a latching issue. d/w not latching properly. How long does it take before the clean light comes on after you reset it. does it fill with water? if so, then your motor may be defective. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a KitchenAid KUDp02FRSS1 dishwasher and it will not respond to any buttons being pushed. The Normal, Light China and Cancel lights continue to blink. I have tried reseting the circuit breaker to power cycle the machine but when I turn the power back on it just continues to blink.


... Dishwashers

Clean light blinking and will not run when start is pressed and red light blinks on start button


Hi,This is an indication that the water did not heat properly. Follow the link below to reset the control and find some tips as to why it failed and how to remedy it. Let me know if this helps. ... Kenmore 24 in. 15932 Built-in Dishwasher

My Kenmore elite dishwasher in not running. The power light turns on when pressed. When I push the start button it blinks and shuts off. the green clean button in also blinking. Model number 6651726


Hi,Close the door and to cancel that just press high temp and heater dry again high temp and heater dry and all the lights is going to light up, its getting into test mode.After that press cancel and now you need to replace the ther ... Dishwashers

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

ASKO 1555 dishwasher won't run. The anti flood device motor won't stop running but we've removed all the water. All the lights on the front panel blink in unison and when we hold down the start/cancel button on the front, nothing resets. We can't run our dishwasher. We've tried disconnecting power and resetting the circuit breaker but the churning motor won't stop.


Hello,Welcome to FixYa.Based on your description " The anti flood device motor won\\'t stop running but we\\'ve removed all the water " It is likely nothing very serious. ... Asko 24 in. 1805 Built-in Dishwasher

Greetings, My Viking disk washer Model # Dfud042 runs 4-5 min then makes several cliking sounds and stops. The program light for the light china is blinking, the soap dispinser still has soap in it, and water remains in bottom of the washer. Regards, James Parker


Hi,\015\012If it is filling and draining ok, then I suggest the problem lies with the main heating element.\015\012Disconnect from the supply and turn off water. Pull forward, to gain access to the element from underneath.\015\012Te ... Viking DFUD042 Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

My kitchen aid dishwasher (8573025) "normal", "light china", "and "cancel" buttons are blinking. I can't get them to stop blinking and cannot get the dishwasher to start .


... KitchenAid Dishwashers

Jenn air quiet series II dishwasher has blinking light on clean and light wash after it runs...it only goes away when we push the off button...it didn't used to do this


Couple of things to check: there's a float that needs to more freely, make sure it does. There's dishwasher cleaning instructions in the operation manual. You may need to take the lower rack out, take off the spray arm to get at a filter, which yo ... Jenn-Air Dishwashers

With Kitchaid dishwasher KUDS01FL, it wont run. All control buttons seem to work (by lighting up when pressed) except "start". When press "start", it doesn't blink or start. Does this indicate a bad start button switch or something else? Is this something I can replace? Thanks.


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

We lost power as our dishwasher was running. When power was restored it seems to be stuck in the drain cycle. We have tried turning the unit off and back on and also holding the start button for 5 seconds.The 4 lefthand lights blink on and off and the right hand lights are steady. It is a model D1996.


Try to unplug it or turn off the circuit at the electric box.............wait ten minutes or so and plug it in and try again..................the program needs to be reset in that manner sometimes....... ... Dishwashers

Green clean light wont stop blinking unable to use dishwasher . It is an energy saver. the drain button works ..and when you push start the light comes on but will not run for cleaning


HiThanks for using FixYa. If the clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light fla ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

ESD402 HAIER DISHWASHER IS BLINKING OP THE START/RESET LIGHT AND THE NORMAL CYCLE BUTTON IS BLINKING. DISHWASHER WILL NOT RUN. PLEASE HELP


Hello,\015\012\015\012Thank You for contacting Fixya.com\015\012\015\012There are some common reasons for this type of behavior shown by the dishwasher:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Pow ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

Hi, asko d3250 will fill and drain(when you press cancel) but the motor will not run. there is a light over the glass icon button that blinks when the motor will not run. what do you think the problem is? motor? circuit board?


This can happen because of multipal reason...The door switch is bad.Dishwasher's cycle selector switch has become defective.Just go through this link ... ... Dishwashers

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If ... KitchenAid Dishwashers

I have a Ge monogram that I purchased in 2003. It is a stainless steel with a touchpad/ buttons on the front. No dials or displays. when I start the dishwasher after about 3 min it switches to China Crystal mode and the red light above that blinks and it stops washing... I canceled the job by holding down the start button for 3 sec it just stops after 10 secs and turns off...


... GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0822 seconds