Having problems with your KitchenAid 24 in. KUDS02SR Built-in Dishwasher ?

I have a kitchenaid dishwasher model number kudso2sr and there is standing water in the bottom of the unit after the cycle is complete. The water will not drain. I ran another cycle and the water still remained. Please help


Answers :

You may have a vacume issue

along side of the dishwasher itself there is a loop of drain hose to create a trap - inspect. also inspect where it is hooked up & follow where the drain hose goes to it's final connection to be sure there are no up hill runs or other blockages.

Speaking of blockages,. did you inspect the dishwasher drain very well to be sure it is fully clear and somethign is not stuck in under the water?

If need be pull the machine out from under the counter and check the side hose and unhook the drain where it goes into your house plumbing...

Dishwashers can be cluegy when it comes to draining...
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS02SR Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kitchenaid dishwasher model number kudso2sr and there is standing water in the bottom of the unit after the cycle is complete. The water will not drain. I ran another cycle and the water still remained. Please help


You may have a vacume issuealong side of the dishwasher itself there is a loop of drain hose to create a trap - inspect. also inspect where it is hooked up & follow where the drain hose goes to it's final connection to be sure there are ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

My ge nautilus dishwasher is not having water run thru the cycles, i ran the machine 3 times and the dishes were still not washed and the tablet not dissolved. My husband sprayed water and cleaned the inside, he removed the filter basket and now the water he sprayed inside will not drain out!!! Please help!!!


... GE 24 in. GSD2220Z Built-in Dishwasher

Frigidare GLD2450RDS0, unit is approximately 5 years old. All of a sudden the water is not draining out of the tub in the bottom. Bailed water out, pulled the glass tap out and cleaned, pulled the lower sprayer out and cleaned, pulled the filter out and cleaned it. Put back together and ran a cycle...still left water in bottom. Help please!


... Frigidaire Dishwashers

2 weeks ago, I had a plumber come and put in a new garbage diposer and since then somewhat old/dirty water seems to be sitting at the bottom after all cycles are done. I calle dhim back and he says that there is no problem in the plumbing but more with the pump. I even use the wt/dry vac and removed water and ran it but still comes back with water at the bottom. also the dishes smell like soap. Help!!!


The plumber did not make an air gap in the dishwasher drain hose when he reattached it to the new disposal. Look under your sink, does the hose (attached to the disposal) go down and through the cabinet? If so, that is definitely the issue. Simple ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Draining problem Water left in dishwasher after end of cycle. Have a disposer, don't have a drain air gap that I can see. Tried to do a cancel/drain, showed 2 minutes ended and water still there. Disposal works fine. What is really interesting is that there is only two of us and at most we've only used the dishwasher thirty times since we had it. Of course- service plan ran out last year (July 07) Please help me. My name is Donna


There is a flapper in the drain hose just where the hose attaches to the pump assembly it has been know to get dislodged and cause a partial drain. With towels underneath hose remove drain hose and stick you finger in and see if it is free moving. ... Kenmore 24 in. 16539 Built-in Dishwasher

WE JUST BOUGHT A NEW DISHWASHER DU1345XTVB HOOKED EVERYTHING UP CORRECTLY AND RAN A QUICK CYCLE THRU IT AND WHEN IT WAS DONE THERE WAS STILL WATER IN THE BOTTOM. THIS WAS TO REPLACE THE OLD DISHWASHER SO IT WAS ALREADY HOOKED UP THRU THE GARBAGE DISPOSAL. WE CHECKED THE HOSES NO KINKS...VERY FRUSTRATED! HELP!! TRISH W.


Make sure the garbage disposal is working, if it is not then it will not allowthe dishwasher to drain. Also make sure there is not blockage in the intake port on the disposal where the hose connects itself. If you installed a new disposa ... Whirlpool Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

Our hot water supply to the kitchen sink became disconnected and flooded the kitchen. Since then it appears that we are not getting any water INTO the dishwaher (just makes a terrible grinding sound..solenoid stuck ?? ). I did put 3 or 4 quarts of water inand it drained alright. Also tried cancelling the cycles but that hasn't helped. We also discoonected the power for a day but still no luck. Please help Ron


... Bosch SHX55M02UC Built-in Dishwasher

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

Put through entire cycle, standing water and dishes still wet, only 1 yr and 3 months old!WHY!!!!!!!!! It also has a musky or bad smell like food in the trash sometimes smells. 500 series 6 cycle stainless steel inside, black 24" in wall. Water is about an inch deep. Have tried it on pots and pans cycle, regular and auto, and have on sani-dry and have spot stuff in it. HELP!!!!!!!!!!


Take the drain hose into a bucket and see if it pumps out.\015\012if it does check for blockages where the hose goes to.\015\012\015\012most likely is a blocked pump, the pump is assesable from in side the sump, you may have to get ... Bosch Evolution 500 SHE45M06UC Built-in Dishwasher

Regular cycle took 3 hours then would not shut off. Stopped at 1 min. soapy water still filled the bottom, dishes had soap on them. water finally drained almost out but I am afraid too run another cycle. any ideas? thanks


There is a heating element in the dishwasher that heats the water to about 155F at which point a thermostat closes and sends power to the timer to advance. If the water does not reach this temp, the dishwasher will not advance. Often the problem lies ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Our 8 year old integrated 2 draw dishwasher (top draw) has a problem on the rinse cycle and constantly beeps and water at the bottom of the draw remains. I have cleaned out all the grit and stuff residual water and tried to use again. But alas there appears to be a blockage still on the rinse cycle. Can you help or do I need to get a plumber? Thanks...Louise


Sorry i lost you my breaker tripped ... Dishwashers

Help! My dishwasher runs thru it's cycles but when I open it I find my second detergent cup still full of soap and my dishes still dirty. I have an older maytag dishwasher but have never had this problem with it. I've tried running a short prewash cycle with the soap despenser open to wash out the soap from the open second despenser but it doesn't wash it out. I know water is coming out of the spray arms but can't see if the arms are spinning although when running it does sound like they ar


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not to open. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Dishwashers

My dishwasher is SHU 3000 series and over 10 years old. The problem is SUDS that will not go away. I have used on-line methods such as vinegar. I have gone through 6 bottles of "Dishwasher Magic" and have put it through cycles not using soap over 30 times and am still getting suds even at the end of the rinse cycle. I have called a local repairman and he says he cannot help me..that I should continue running the dishwasher time after time till the water is w/o suds. Any help for me?


... Bosch Dishwashers

Have SHU43C and have had no problems with it. We usually run it on the Quick Wash cycle, but ran it on the Regular Wash cycle yesterday because the glasses seemed to be coming out spotty. After it ran, there were no lights on the display like there usually are. The washer had run and the dishes were clean, but it has not drained completely. There is still about an inch of water in the bottom, despite removing and checking both the Large Object Trap and Fine Filter (neither which were clogged


The drain pump needs to be replaced or cleared of obstruction. ... Bosch 24 in. SHU43 Built-in Dishwasher

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

I have a blinking cancel light on model GU1200xtlt1 and will not start in any cycle. Also if I push another button it flashes rinse button and cancel button. Before this it ran in Sani Clean over and over again and I could not change the cycle. I emptied out a bit of water from the bottom because it did not drain also and the water was not smelling too good.


... Whirlpool Dishwashers

The dishwasher fills with water, but the sprayer arms do not spin. The water will drain at the end of the cycle, but the dishes are still dirty and the detergent is still in the cup. Can anyone help before I call Sears?


The sprayer arm is not in place, broken or hitting/ touching a dish. see if u can reseat the arm to the tube. ok ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Miele G570 dishwasher and the spinners don't appear to be turning properly. I have removed and cleaned the incoming water strainer, but still no better. The water supply pressure is the same as always. The unit goes through it's complete cycle but the dishes are still not clean. Can you help please?


Run a nice long hot "Pots and Pans" cycle every now and then.Try calling the Miele Appliance Hotline 1-800-999-1360 when your in front of the machine. ... Miele Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

Our maytag is about ten years old. No big problems that a little vinegar wouldn't solve once in awhile. Lately, we ran out of water softener salt and a white film was on dishes and not getting clean. I filled the water softener again, and did the vinegar wash, which helped a little. Now dishes not getting clean. I got desperate and did an empty load with CLR in it. Still, not effective. I feel as if something is clogged with lime or calcium since a pan placed in there on bottom shelf still had


The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the ... Maytag 24 in. MDB4100 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2019 seconds