Having problems with your KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher ?

Screw dropped in bottom of dishwasher-how to get it out?

\015 I've dropped a screw into the dishwasher and need to retrieve it - how do I disassemble the sprayer arm\015

Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Installing security braces for dishwasher, a screw dropped down in perforated area in bottom . I can no longer see the screw. what steps can i take to retrieve the screw. Can i continue to run the dishwasher . Will it harm the dishwasher if i can't get screw out..


... Samsung DMR77LHS Tall Tub Dishwasher

Screw dropped in bottom of dishwasher-how to get it out?


... KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

My dishwasher was not getting the dishes clean, so i started taking the lower end apart to clean, got to a gray wheel looking object with a screw in the top which was recessed and still the wheel looking object will not come off, it will spin but will not come off, I need to finish taking it off because I dropped a screw down in the bottom area where the water settles.


If there is still standing water in the bottom of the dishwasher, remove it with a wet vac then look for the missing screw. It might be in the vac.\015\012\015\012If no luck, try using a good small stick magnet to retrieve the screw. The ... Maytag 24 in. MDB4000 Built-in Dishwasher

Screw drop Hi I was installing my new LG dishwasher and I droped a screw in the hole in the side panel where you can put a screw to connect to the side of your cabinet. There is a small plastic cover which I removed where you can screw a screw into the cabinet. However the head of my screw was too small and fell in the side panel. I can not get the screw out or see it now although I know it is in the dishwasher. Is there anyway of getting it out or will this cause a problem? Since it is in t


A great retrieving tool for this is a flexible shaft magnet wand. I strongly recommend this tool be placed in everyone's toolbox.\015\012\015\012as far as leaving it there if not found? probably safe from electrical. will years of vibration allow it ... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

I dropped something in the bottom of my 665.1374 ultra wash dishwasher. Is there a way to get it out? I've taken off the wash arm and found four screw but one of them is under the white stationary part that runs down from the back of the machine.


... Kenmore Dishwashers

Kenmore dishwasher how do I retrieve a screw I dropped in the bottom?


Try turning off the power at the breaker box, turning off the water, and unhooking any connections. Next, remove the dishwasher from the counter, and turning it upside down. You'll want to shake it gently at an angle so the screw can drop free. This ... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

A glass shattered in a thousand pieces in the dishwasher. I cleaned and vacuumed everything except the very bottom that I can't get to. I took out 8 screws, removing the round rotator piece at the bottom, but that still doesn't get me into the very bottom where I'm certain there is still glass. Question #1 - Will leaving the glass down there hurt anything? Question #2 - If yes, how do I get the rest of the part off without damaging it? I have a 10+ yr old Model DU920QWDB3 Thank y


The glass should just go down the drain from there. I doubt any piece that made it into there should damage anything as they are would have to be pretty small and as big as any food particle that could fit into there so you should be fine. If you rea ... Whirlpool Dishwashers

The screw that was holding the dishwasher dropped into the holes on the bottom of dishwasher. What should I do? I tried to use magnet to retrieve the screw, but nothing came up. Is it safe to use the machine with the screw still lost inside the machine? Will it damage the machine if not recovered?


... GE Nautilus 24" Built-in Dishwasher

Whirlpool DU6000XR Dishwasher. How do you get the bottom panel off to get to the underneath? It seems there are screws on the top of the panel but the door is in the way.


You should be able to still reach it with a screw driver ... Dishwashers

Dishlex DX102 How do I get access to the impeller. I have broken down and cleaned everything from inside the dishwasher, but the water still does not pump away. It pumps in water okay, but not away. How do I go further, the last two screws drop the whole unit down, do I have to pull the dishwasher out and go thru the front kick panel?


Your outlet path is most likely clogged with food, the remains of paper labels, or a combination of both (assuming the sealing plug was not left in your disposer unit). I've taken lots of these apart and they are all slightly different. Hopefully y ... Dishwashers

A screw fell in to the bottom of my dishwasher. In trying to get it out it disappeared. In trying to find it we found another one that looked like it had been there a long time. My dishwasher is old model #DU920GWBD5. Do you think we can run the machine?


... Whirlpool Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Loud grinding noise sounds like something small and hard is getting caught in some kind of rotary. The sound comes from underneath the dishwasher at or near the motor. I screwed the big circular plastic filter on the bottom of the inside of the dishwasher, but found no significant debrie. It did not resolve the problem.


... Jenn-Air 24 in. JDB1090AWS Stainless Steel Built-in Dishwasher

After the dishwasher finishes, I notice a green/blue liquid leaking from the bottom of the washer onto the floor. It has a consistency of oil. I have solved this in the past by tightening the screws at the bottom of the washer panel. The leaking is getting worse. Model GSD5500G03WW Serial GH88772BB


... GE Dishwashers

Dropped screw in bottom of dishwasher - Dishwashers


Try a magnet . if that does not get it . try to remove bottom sreeens . but you should get it out before running it . it will damage the pump impeller . mm ... Dishwashers

Model KUDS22OT3 --Dishwasher door opens such that it drops past the stop on the right arm-- stopped by the bottom panel. cannot close unless you strike the little stop to get it back into the slot.


Much like an oven door this is removable, you simply have to remove and install correctly, it very unlikey you broke any components already as they are all steel. It is tricky but you can get it back in the appropriate slot. ... KitchenAid Dishwashers

I am looking for a manual to remove the bottom sprayer on a Maytag DWC 8240 AAW dishwasher. This is a portable unit that has chipped the crockery since we bought it. Now during only the drying phase there is a grinding noise that sounds like the glass chips are being ground up. There are some screws that I can remove to find what I think is the filter. How do I get to the filter?And where can I find an exploded parts diagram? Thanks


... Maytag DWU9962 Dishwasher

Our Kenmore dishwasher 665.1726 doesnt seem to be cleaning as well. LAst time this happened a serviceperson cleaned out a filter where food debris had clogged the water flow. We were able to take off the bottom wash arm but couldn't figure out how to get the filter off (there are 4 screws holding it in place and one is under the plastic arm that caries water to the sprayer.


I had the same problem!\015\012\015\012The arm WILL come off....you have to pull the screen off. ... Kenmore 24 in. 15689 Built-in Dishwasher

I have a dwu6750aam maytag dishwasher. It won't drain completely. I have taken the sprayer arm and strainer off. Now how do I take the impeller off. I have also dropped one of the sprayer arm screws into bottom of the tub


... Maytag Dishwashers

Indesit idl535 dishwasher door is loose at bottom right hand side. how do i get to see if it just needs tighten a screw?


... Indesit 24 in. D63 Free-standing Dishwasher

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Hello, I have a Kitchen Aid dishwasher, model KUDS30IVWH3. The dishes have not been getting as clean lately, the bottom is decent but the top rack is not getting very clean. Also, when I open the door after the cycle is done, there's a bunch of detergent at the bottom of the door and on the floor of the dishwasher, like it isn't getting sprayed all over or something. Don't know if I have to check the water intake valve or if maybe the sprayers could be partially clogged.


... KitchenAid Dishwashers

I have a kenmore quiet guard standard dishwasher. About 2 weeks ago it started leaking. today I pulled it out and found that looking straight ahead at the door on the lefthand side under the bottom is 2 small wire metal fittings that screw up into the bottom of the dishwasher. one was loose and dripping water. when i screwed it back in i noticed that it was stripped out. can it be replaced or should I scilicone around it to stop it?


... Dishwashers

Dishwasher problems I have a counter top dishwasher and it's not cleaning things like it used to i think its clogged but i cant get to the drain because it is in the bottom i tried draino but it didn't work i also tried unscewing the bottom but i cant get that part out i think there is somthing stuck in there.


First thing to check water hose that connect at back of machine. pull the screen out and clean it. use a pliers. I run my under water then use a q-tip if its clog to clean the rest.\015\012\015\012Then pour a cup of vingar in machine and ... Danby 22 in. DDW396 Free-standing Dishwasher

Question re: potential damage due to dropped screw


ANYTHING that is not supposed to be in the main wash pump can potentially cause significant problems if not removed. Foreign objects caught in the main wash pump are the most common causes of dishwasher failures. Ignoring it can eventually lead to a ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1891 seconds