Having problems with your KitchenAid 24 in. KUDS25 Built-in Dishwasher ?

I am an appliance repair technician. But, this one is stumping me. Kithenaid DW. Overfills and runs over onto the floor when NOT in use. I have replaced the inlet valve and disconnected the wires from the valve it still happens. Bizarro!!!


Answers :

What??!! That is bizaro? If you have done that then logically it must be leaking BEFORE the solenoid, yes? OR the solenoid is some how Stuck Open? I mean that all I can think of, as if it is a NEW solenoid, the in non-operation mode is NC, AND the drive wires are OFF, then?? I know this may sound ODD, but maybe the new one is stuck open too. Give the solenoids a good whack or two & a soak in CRC, WD40 or the like? see if that somehow frees them up.
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS25 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am an appliance repair technician. But, this one is stumping me. Kithenaid DW. Overfills and runs over onto the floor when NOT in use. I have replaced the inlet valve and disconnected the wires from the valve it still happens. Bizarro!!!


What??!! That is bizaro? If you have done that then logically it must be leaking BEFORE the solenoid, yes? OR the solenoid is some how Stuck Open? I mean that all I can think of, as if it is a NEW solenoid, the in non-operation mode is NC, AND th ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Inlet Valve keeps stopping and starting, takes a bit of water then stops take a bit more then stops, on off on off for about 10 mins until its taken enough water to srta the cycle , have replaced the Inlet Valve still happening and water flow meter with pcb still happening Any suggestions? It a DWLT65


What about the overflow valve? It could be sticking ... Beko Dishwashers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

I have an Electrolux ESI 6104x. Regularly just after starting the dishwasher as it starts to fill for the first time the water inlet cuts out. If you turn the water off at the mains disconnect the inlet pipe (spilling a bit of water in the process) reconnect the inlet pipe and turn the water back on the dishwasher fills and runs perfectly. This fault used to happen occasionally and now happens regularly.


Disconnect the fill pipe from the back of the machine and you should see a small mesh strainer in side the dishwashers inlet valve. Check that this is not dirty - to clean it pull out the strainer and rinse under the tap. ... Dishwashers

Can I replace the inlet valve with a different inlet valve than original. I have a 3378779 I want to use a whirlpool valve I found on line for $17.


You need to make sure the coil voltage is correct, the threaded connections are the same thread, the threaded connections are properly oriented, and the new valve will fit into the space of the old valve, or you'll spend more time making it work than ... Whirlpool 24 in. GU980SCG Built-in Dishwasher

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

Whirlpool dishwasher, replaced water inlet valve and float switch and still no power to selonoid on inlet valve.


... Whirlpool Dishwashers

My Karcher 330 M has blown two water inlet ( Garden hose inlet ) elbows. Replaced one and then after about 5 min operation shut off the valve on the wand and immediately the new elbow split the same as the first. The garden hose I was using has a shut off valve could this caude the problem?


I have a larger gas powered karcher, just make sure the water going to your karcher is not obstructed from its path. on mine i bought a goodyear hose that can be purchased at northern tools or any hardware store. and use it just for pressure washing. ... Karcher PSI Electric Pressure Washer

No water Thanks for the try, but I have already replaced the inlet valve. Still no water. I also checked and confirmed that I am not getting 120v to the inlet valve and/or float switch.


Check your heat dry options I have seen them short out a lot and that will prevent the water valve from getting 120v. ... Frigidaire 24 in. FDB126RB Built-in Dishwasher

Attempting to install asko d1706 dishwasher. Bought used, had no hoses with it. when trying to connect water inlet hose, unable to connect without leaking. Finally got a connection on there that has it slowed down to a drip. does the inlet valve need to be replaced or is there a special inlet hose that we don't have?


Yes there are actual dishwasher supply hoses you can purchase at most hardware stores.... if you do have the correct hose may try to put some teflon tape on connection so that leak stops....\012good luck to you ... Asko Dishwashers

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

Dishwasher wont fill replaced timer and inlet valve


Its fucked. ... GE 24 in. GSD2220Z Built-in Dishwasher

Wont fill with water, replaced the inlet water valve,still wont fill


First of all make sure the water shut off is on. Second check the water float is it jam on the top position that will shut off the water. then the timer switch that control the water inlet valve.Hope this 'll help. God Bless. have a nice day. ... Kenmore Dishwashers

Hotpoint fdw70 error code A10 have replaced the inlet water valve but still have an error code flashing A10 hoped to find a reset button but cant find it anywhere can u possibl advise.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Asko d3100 dishwasher still giving problems after replacing inlet valve. When you press the start button all of the lights come on and there is some pumping sound with a dribble of water coming through from the right hand side. When you take your finger off the start button everything stops, no lights, no pumping. Anyone got any ideas?


Hi.To start, disconnect power and ensure that there is no water in the tub when you restart the dishwasher.It looks like the overfill switch is preventing the machine from filling. The overfill (water level) switch is either a ... Dishwashers

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

I had a problem with my dishwasher popping the breaker. I opened the bottom and found burnt up wires. I fixed those and now the dishwasher stays on and begins its cycle (by draining) but the water is not flowing to the machine. It has supply, and I just now replaced the water inlet valve- no difference. The water was working before the breaker issue. I'm wondering if it is now something as simple as a clog somewhere since the washer sat unused for a month; or, if it is something more compli


I read your previous problem. This appears to be separate problems. The first was likely a loose wire. When a wire has a loose connection they build heat and can melt. The current issue would seem like the float switch is stuck. The float switch is ... Bosch SHU9925UC Built-in Dishwasher

Hi, I have a Maytag Jet Clean D/w. There doesn't seem to be any water entering the d/w when it is turned on. I have replaced the vater inlet valve and still have the same problem. Any suggestions?


If there's no water entering your dishwasher, check these: \015\012 \015\012Water-inlet valve \015\012The water-inlet valve lets water enter ... Maytag Dishwashers

I have a pot scrubber 600. I just replaced the water line. I had to disconnect the electric wire to service the unit. Everything is running except the water doesn't fill, and there is an awful buzz from the actuator for the water discharge. What is going on? The water valve is on but doesn't fill.


So tell...me...you replaced the water line why......its probably moot as to why you did it....just realize that the large majority of no water problems are due to a wire off or loose on a water solenoid valve or a bad solenoid....I am going to provid ... GE Dishwashers

Dishwasher is not getting water. The motor runs, but there is no water going in. Was doing it once in a while, but now all the time. I ordered and replaced the water inlet solenoid / valve thinking that had to be it, but wasted $45.00...still doesn't work!


Does valve make noise . water to valve ? ck float may be stuck something under it or switch under float ... Kenmore Dishwashers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Completely dead. breaker is fine. have live power at dishwasher. ???? Replaced heater, pump and check valve last year. No obvious burnt or disconnected wires.


There is a thermal fuse located behind the operator console on nearly all Kenmore or Whirlpool manufactured dishwashers. There were some noted problems with certain model dishwashers where the wire gauge on the thermal fuse was too small and would he ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1500 seconds