Having problems with your KitchenAid 24 in. KUDS25SH Built-in Dishwasher ?

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


Answers :

You just need to clean the pump area in the bottom of your unit :)
try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :)
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


You just need to clean the pump area in the bottom of your unit :)try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :) ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?


It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Whirlpool GU1100XLTQ1 dishwasher, 4 years old is leaking water during cycle. I cannot see exactly what is leaking by looking up through the acess panel in front...there are what appear to be plastic support ribs for the tub and water is leaking through several of them to the left of what appears to be the motor in the center...please help! I don't think I can run the washer and tilt it back at the same time as the water supply line only allows me to pull it out just enough to clear the counter t


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wahgfadh ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

I have a Bosch SGS43A22 Dishwasher approx 8 years old. When I start a cycle it fills, runs for about 15 minutes, then drops out about a litre of water from the bottom of the door, then completes the cycle without any more leaking. I have run the machine with the front panel off and can see that water bypasses the top of the seal and fills the well of the seal then pours out. It only happens the once. The seal is fitted correctly. Any solutions?


After 8 years service the seal may have perished, so you should feel for a crack by stretching the rubber where you noticed the leak. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

Hi there,i have a brand new but 3 year old,diplomat 8332,just fitted it,it does the pre was ok,pumps out the water,goes to next stage,you can hear water entering the machine,shortly after it has started the main wash,it starts to cut out intermittantly,then F2 code appears,and a bleep.i have taken the lower panel off and checked for leaks and to see if the valve was free,all ok,also relay click in front panel,safety cut out ? any ideas please.


... Dishwashers

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

I have a Bosch SHU43C. I have a leak it seems to come out from the door. I removed the front panel. Inspected the seal and all seemed smooth and not damaged in any way. So I decided to run the machine. Waited for a few minutes and the water leaked from both corners at the same time. The water settled in the rubber trough under the door. After a few more minutes the water leaked over the trough and onto the foor. Is there to much water entering the machine? What limits the water entering


... Bosch 24 in. SHU43 Built-in Dishwasher

Miele 646 sc plus inlet tank solonoid valve on water tank leaking. We moved the machine from one room to another and now this valve is squirting out water. We replaced both door seals thinking that was the problem, then started the machine with a side pannel removed, and saw the jet of water coming from the solonoid valve on the water inlet tank. Any ideas.


... Miele Dishwashers

I have a brand new Blanco dishwasher but im unsure if it is a DWF6XP, DWF4X or DWIN7 model. It does not have a salt dispenser if that helps. Last night when running for the first time i had a plumbing issue where the drain pipe was not set high enough as it states it has to be 500 to 100cm of ground height. Also had a leaking sink drain pipe. Fixed all that and turned machine back on and it pumped all the water that was inside to drain. I have cancelled the program and restarted but now it is ru


Unplug it and wait 5 minutes. Plug it back in. This will reset the machine. Put it on full cycle and allow it to do a full cycle. It should work just fine. ... Dishwashers

I have a craftsman 580.752020 pressurewasher bought it last year and it worked fine until yesterday it now shoots a very puny steam of water with no pressure at all I cant hook the hose direct to the machine because it has a quick up is there any other test I could run


... Electric Pressure Washers

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

Maytag jetclean dishwasher leaks: Water leaks underneath. I don't see the source of the leak but see water running out on the left side about midway back on the bottom. Could it be related to the little plug inside the unit on the left side halfway up?


... Dishwashers

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

Westinghouse SB915WJ is leaking cold water underneath machine. Working fine, just leaking water. Have changed door seal but it is still leaking. Also tried leveling it but this has not helped. Would like to access underneath and see if clamps are on tight but don't know how to access this part of machine.


... Westinghouse Dishwashers

Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.


Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1552 seconds