Having problems with your KitchenAid 24 in. KUDS25SH Built-in Dishwasher ?

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

I have a whirlpool du1055xtsq3 dishwasher that is partially working. Cycle buttons light up but start button does not. I've tried resetting by pushing sani-rinse and heated dry alternately. Control panel lit up and heard motor running but no water. Your help is appreciated. Unit only 2yrs old. Thanks!


... Whirlpool Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Have a LDS 5811WW dishwasher that will not power up. Do not have any panel lights or "ding" noises. Have ac volatage to the unit. Red LED light on controller board not lit. Tried new board. Still no LED light or panel lights.


Which control board have you replaced. There are two boards in the panel. See ... LG 24 in. LDS 5811 Built-in Dishwasher

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Kenmore Ultra Wash Model 665.15801891 (Serial FJ3403697). This is in the USA. Unit will not run. Two lights are lit on the display panel and do not go off - 'Drying' and the #2 on 'Delay Hours'.rn I have turned off the power at the breaker box hoping it would reset. Once power is turned back on the Lock light comes on. I can clear that by pressing 'No Heat Dry' for 4 seconds but then the 2 lights mentioned above come on and do not go off. Any suggestions? Can you tell how old the unit is by t


Plase confirm if your model has the same front panel as the one shown in this manual.\015\012In that case try this sequence to reset the dis ... Kenmore 15899 Built-in Dishwasher

Came home and dishwasher was stil running from the morning. Opened the door and all the lights on the control panel were lit up and unresponsive. cut power to unit for 1 min and now the controls don;t light or respond to anything . They are not locked and there is power to the unit any ideas ?


Hi\015\012\015\012\015\012Thanks for using FixYa. From what you have described it seems that the control panel has gone bad and needs to be replaced however, if you want more information then please do revert with the manufac ... Dishwashers

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

The normal light is flashing on the panel but unit will not run. I tried a new control board and bi-metal fuse. The light is still flashing and dishwasher will not do anything. Kitchenaid model kud1021rbso. Any help would be greatly appreciated.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Start and resume button flashes. Unit will not restart, cycle or cancel operation. Tried turning off electrical supply to re-boot control panel but that did nothing either. Is replacing the control board possible for a competent DYI-er?


... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

Dishwasher won't go into rinse cycle. Lights flash on control panel and the unit cyles on like it's trying to fill, but doesn't fill. It will cycle on and off several times over an hour's time period before it finally starts running again.


Check water flow into the machine. check strainer attached to the machine. Clean if clogged. ... Whirlpool 24 in. DU920PW Built-In Dishwasher

1998 KitchenAid Dishwasher model KUDM24SEWH2 - cycle and start buttons light up, but once the water has finished running the machine does not start, but "tries" to start every 20-30 seconds. Selecting Cancel provides the same results. Do I need to replace the control panel? Thanks! Stephen


... Dishwashers

My whirlpool dishwasher is ocasionally filling back up with water, whether the door is open or closed, and regardless of of control panel being lit. It happens, then leaks out the front. If i run the cancel drain, it will pump out the water just fine. All the other cycles are working just fine, and it leaves no water at the end of of the cleaning cycle. I have found no common occurance for this


Greetings,\012\012 in most instances the water inlet valve is leaking..this is the water valve that brings water into the dishwasher...its possible, the drain water is running back into the d/w from the drain hose not installed prope ... Dishwashers

Unit will not run. cannot enter diagnostic mode.


I would say that you have a bad touch panel..99 percent positive ... Dishwashers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have a Whirlpool Quiet Partner 3. It sat up for a few months because the control panel went out and it took a while to save up and order a new one. Now it blew the thermal fuse. I put a 15amp automotive fuse in it to try it, and it runs until it fills up and blows the fuse again. I am trying to figure out how to test the motor and the heating element to see if they are shorted. My local repair shop told me that they want to replace my new panel with their panel first, and that after that


A 15amp automotive fuse is rated for a 12VDC system in an automobile, not a 125VAC houshold electrical system in an appliance. I don't think your automotive fuse can handle the start current being drawn by the main wash pump as the dishwasher starts ... Dishwashers

I bought a used 001355 asko dw. the front door panel and all under panels are naturally loose and I'm having trouble figuring out the reassembly order. And then as I was trying to install the main galvanized under panel, a short galvanized sheet metal part fell out of the door inside the unit. That's the part that now has me really stumped. Can I get a picture of the front of the unit, preferrably an exploded view? Thank you. Paul Cowden. (415) 777-9858 or (415) 302-0628.


... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

How do I reset a KitchenAid Whisper Quiet Plus? Right now, if I try to initiate a heavy cycle (or normal cycle, or whatever) all that happens is the cancel light lights up and the dishwasher makes a moaning noise. If I let this run its course, nothing happens (i.e., after the moaning stops and the cancel light is no longer on, if I try to initiate a cycle, the same thing happens all over again).


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1377 seconds