Having problems with your KitchenAid 24 in. KUDS25SH Built-in Dishwasher ?

How do i put the lower spray arm back together? I had to replace the top screw part and it seems to stand up to high. I have a small white plastic ring, a larger white split ring and the arm itself. I have tried every configuration to put this back together but it is not right - the new "screw" part number is the same as the original.


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i put the lower spray arm back together? I had to replace the top screw part and it seems to stand up to high. I have a small white plastic ring, a larger white split ring and the arm itself. I have tried every configuration to put this back together but it is not right - the new "screw" part number is the same as the original.


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Hi Model DU1048XTPQ4...when I started the DW today, it sounded kind of loud. I let it continue, then I smelled something burning. What I think happened is that the lower spray arm is too loose-so when it spins, it gets stuck on the heat ring on the bottom of the DW and then the plastic parts start to melt. We disassembled the spray arm and there was lots of calcium/lime build-up. So we cleaned all of that out, put it all back together, but the spray still seems too wobbly. Went ahead and start


The noise coming is from the motor bearings or the impeller which moves with the motor.both has to be checked.\015\012if the bearings are making noise motor needs replacement and if impeller is cracked it needs replacement.\015\012you can get require ... Dishwashers

Hello - I have a LG LD 2060SH and wanted to clean it completely - sadly I have a part called the Valve or Float Component (small white plastic thing!!!) and I can't locate where it should go! Yes, I undid all the bottom filters on the water inlet system and spray arms, they were all clogged even after special cleaning - Can you explain where it goes as I put everything back together - now it is all squeaky clean! I knew I should have taken pictures along the way, but I was so happy that everyth


There should be a little hole in the bottom of the DW and it simply slips back into that hole. ... LG Dishwashers

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

The top spray arm of my Frigidare model FBD4315LFC0 Aqua Surge dishwasher fell off. Their appears to be a missing part. I've been searching online for a schematic and can't find one thorough enough to use. The parts I have are: 1. The top sprayer arm (the one in the top of the tub) 2. The two piece plastic keeper ring that appears to fit into the top of the spray arm. 3. A small white grommet looking item that fit inside the keeper nut. 4. The keeper nut that screws directly onto the wate


Hello there:hey sorry i keep getting disconnected i will be back on really soon i need to find out what is going on i hope these things that i have discussed with you is helping you out the parts are not as hard as they look once yo ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

The maytag dishwasher model mdb7130AWB stoped cleaning correctly so we went from the arm assembly in bottom of dishwasher down to the cutter disc and we found a crack in the housing so i ordered that piece. the new part was designed a little different but we put it all back together the way it came off. but it started and ran maybe 1 minute and stopped. so i have pulled up the diagram and see some problems. in the current diagram. original there was no part 37, 17 19 and 3, alos the crew d


... Maytag MDB7130 Dishwasher

The overflow air drain on top of the sink that is connected to two hoses under the sink is leaking. It leaks out the top onto the counter. I took it abart but am afriad I did not put it back together right. There is a rubber ring that I think must be for sealing and I put it directly on the counter and then screwed down the air valve over this and water s coming out of the air flow valve and all over the counter.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

I need the diagram for the door pulley system so I can make sure I am hooking it up right. The original door chord/pulley assembly broke. I ordered new parts, Now I want to make sure I am putting it back together the right way. The edge of the screw- on floor panel is pushing the plastic hook off of the door hook when you shut the dishwasher door.


... KitchenAid Dishwashers

I dropped something in the bottom of my 665.1374 ultra wash dishwasher. Is there a way to get it out? I've taken off the wash arm and found four screw but one of them is under the white stationary part that runs down from the back of the machine.


... Kenmore Dishwashers

We removed the round screen because it was clogged and the white piece fitted in the screen popped off and we can't find it to put it back together. Can we order this single tiny part?


YES SEARSPARTSDIRECT.COM YOU CAN LOOK AT THE UNIT AND ORDER THE VENT SCREEN THERE ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Spray arm, 3rd level, fell off. Flower-like looking ring is still attached to top of dishwasher and arm itself is no longer attached. How can I reattach the spray arm to the flower-looking like ring?I have Frigidaire model number PLD4555FRC0; part # of spray arm, 3rd level, grey is 154478202. I called help line and got someone whose accent I could not understand. I think his name was Victor. He left the line and never came back but, before he left, he said he was looking for the part...why he, t


Unscrew the flower looking piece, there is a white plastic retaining clip inside- press it back together. ... Frigidaire PLD4555RFC Dishwasher

Remove the lower wash arm (1) by turning the nut (4) clockwise (right) lift the arm off, there is a bearing (3) (small thin plastic washer) under the arm, be sure not to loose it. Lift the tab on the back of the feed tube cap (2) and swing it to the right and lift up, this may need a bit of pressure to release it This is for my Whirlpool dishwasher DU1100XTP. I'm putting it back together and can't remember if the plastic washer goes on top or underneath the feed tube cap. Also how do I remo


This is not a tuff job plastic washer goes on top . and torx screws . you use a proper torx tip for the screw size . ( you can go to sears parts .com and put in model # and see a good break down of the wash arm s and t ... Dishwashers

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

I have a frigidaire dishwasher 4000 series aqua surge with speed clean. The small spray arm on the ceiling of the washer came off. I found it sitting on top of some cups in the top basket. There is a loose part inside the retainer in the ceiling that moves back into the retainer when I try to put the spray arm back on. How do I fix this and how do I get the top basket out to work on it?


The top arm snaps into place. Simply unscrew the retaining clip from the ceiling of the washer. Inside of there, you will find a small white plastic clip. Make sure the two prongs are pointed down and poking out through the hole in the bottom of the ... Frigidaire PLD4555RFC Dishwasher

The spray arm, above the top rack, keeps unscrewing during the wash cycle. Just the arm comes off leaving a round plastic part attached to the top. This can be unscrewed and inside is a white 'washer'. The arm can be clipped back but comes off again in the next wash. The plastic 'washer' has to be turned over to allow re-attachment. Is a washer missing from inside?


Could the arm be mounted upside down and rotating the wrong way? Just an idea... Some of these can fit either way and the retainer will fit either side of the arm. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a Bosch SHU8805UC/14 dishwasher. I took the front door panel off to install it better but ended up with two extra pieces that look like either part 935400 Door Guard, or 935526 Support. I cannot seem to find any place on the inside of the door where these pieces would fit. The dishwasher works fine but seems like it got noisier after I put it back together without these two parts. Can you help me locate the proper place for these 2 plastic parts?


Hello, \015\012\015\012Welcome to FixYa.\015\012\015\012I believe the parts you are referring to are likely the blocks in each corner of the outer door panel. These have been a sticking point for many I tech over ... Bosch Dishwashers

Need to put inside parts back together


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I removed the spray arm in my kitchenaid dishwasher KUDP02SRWHO and can't put it back on, any helpful tips to put this together again?


SIMPLY FORCE IT IN ITS PLACE IT SHOULD CLIP IN ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I have an inglis ipu5846 built in dishwasher it fills thaen trys to start but wont start or drain now i took off the lower spray armthe part that is screw down under it tryed cancel drain and it worked put thetop bacck on but not the spray arm and it wont work.what stopping that from working there are not any moving parts on that piece


... Whirlpool Dishwashers

I have a Bosch dishwasher, model SHU9915UC/U11. The spring mechanism on the detergent door cracked, and I bought the part to replace it. I took the front cover off of the dishwasher to determine how to replace it. Two white plastic "things", maybe spacers, fell out. I need 2 things: a) how to gain access to the spring on the detergent door so that I can replace it, and b) how to put the door spacers back on. An exploded parts view would probably help a great deal. Michael J. Orr


Hello! This is Guru...Saailer...I have your information...Due to size limitations I'll need your e-mail address in order to send it to you...Send an e-mail to me and I'll send an exploded view diagram and parts list...Guru...saailer... ... Bosch SHU9915UC Dishwasher

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a frig/electrolux gallery series dishwasher: model GLD2445RFC0 serial # TH72896159. On the ceiling of the dishwasher is a gray plastic arm that snap onto a round gray disc that screws into the ceiling. It will not stay connected to the disc eventhough I snap it on with a round white plastic doughnut kind of cap. I have replaced the gray arm in the past because the orig. one fell and melted on the heat ring. This one has : 1546496 1546079 CAV 2 >PP+20TF written


If you go to searspartsdirect.com and type in 154607802 for the part #, I'm pretty sure that's what you are looking for. I broke the exact same part and it's what my husband ordered as a replacement. ... Electrolux Dishwashers

My 14 yr old Magic Chef Model DU4K seems to be leaking (it is dripping into the basement just under where the dishwasher is located). it started when the arm at the bottom of the dishwasher did not seem to be moving so my husband took off the bottom "grill" to see if maybe there was something under there preventing it from spinning. It started to leak when he put it all back together (the bottom arm is still not spinning)


Being 14 years old I dought if spares are still available for this machine personally at 14 I would rather replace the unit if you are not in a possition to replace it you could advise from your local appliance repairs as to weather parts are availab ... Dishwashers

We have an Miele G868. The upper arm just came off and we can't get it to screw back on. We see the threads on top put its doesnt screw on just falls off


... Miele Dishwashers

Removed housing from pump to retreive broken piece of glas found 2 white plastic balls laying on bottom have to put back together where do i put the plastic balls


Hi\015\012\015\012Please check this video for installing plastic balls:\015\012\015\012 ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1107 seconds