Having problems with your KitchenAid 24 in. KUDU02FR Built-in Dishwasher ?

Normal, Light China lights flashing, but dishwasher won't start. Hit Cancel, that light starts flashing.


Answers :

What is the model number of the unit in question please?
\015\012Thanks!
Hello. You may be able to solve this problem by going to the electrical panel for your home and turning off the circuit breaker that feeds the dishwasher. Leave the breaker off for two full minutes. If you have fuses, remove the fuse that feeds the dishwasher in that same electrical panel.
\015\012
\015\012IF that does not solve the problem the door switch may be the culprit. It is important because, if it's defective, the dishwasher won't work at all. To reach it, you need to remove the control panel cover, or sometimes the interior liner of the door. If it's defective, you need to completely replace it. Joe
Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Normal, Light China lights flashing, but dishwasher won't start. Hit Cancel, that light starts flashing.


What is the model number of the unit in question please?\015\012Thanks! ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

Kitchen Aid KUDIO1ILBS5... Normal Light keeps flashing green and wont start. When I press the cancel button, it flashes too. If I hold down the cancel button fashing light goes away on cancel button, but not the normal button... It continues to flash.


Hi,\015\012\015\012Close the door and to cancel that just press high temp and hetaer dry,then again high temp and heater dry and all the lights is going to light up, it getting into test mode.After that press cancel.\015\012 ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a kenmore dishwasher model 66515832000 and it starts to do the cycle and about 10 seconds into it it stops and the quick rinse light starts flashing, it wont cancel or let anything else happen. if you open it and shut it , the light just flashes and nothing will work.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Start light keeps flashing but washer won't operate. Tried to reset by hitting cancel button but start light keeps flashing.


Check whether inlet water is flowing into the machine. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers

I have a Kitchenaid 9741068h whisper quiet. It fills heats and then the cancel light starts to flash. it sounds like it wants to start but will not kick over. I can hit cancel a couple of times and it will work after several attemps. any help out there?


... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

FDB1050REC2 I have loaded my dishwasher and hit start and the washing light is just flashing. The door is closed properly and there is some water in the bottom of the dishwasher. It wont run the washing light just flashes... I have flipped the curcuit breaker but that didnt do any good.


Follow up to my Jun 02, 2008 post. We had a service tech come out\015\012today, and it turned out that the door switch was bad. The\015\012neutral side had continuity with the door shut, but the hot side was\015\012sporadic. A new switch has been ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Kud101t cancel,rinse and heavy lights flash wont start


... KitchenAid Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers

Dishwasher Kenmore Ultra Wash model #1777990 the 2 hour delay light is on and when I try to cancel the door lock button starts flashing I hit cancel and open the door and shut it and the 2 hour delaay button cmes on and will not go off. Is there a reset button anywhere.


... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Whirlpool gold, about 2 years old. the "clean" light is flashing. When I hit cancel, a 2 minute dry(?) cycle runs. The clean light resumes blinking. It will not start a new cycle


Looked in the manual and called a repairman ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a GE dishwasher model number GLD55OOLOOWW. It was starting a start cycle and i opened the door to put more dishes in and my finger must have hit a button on the door and now two lights flash off and on and it wont reset itself. It has been on for several hours and still blinking and beeping every so often and unplugging it does not help. Any suggestions how to solve this problem. Thank you.


Try pressing the cancel button ... Dishwashers

Du1145xtpba quietpartner II starts then stops shortly into cycle and the normal wash light just blinks, if you hit cancel then both lights will flash when unplugging/reconnecting ribbon cable from control board it will complete 1 cycle and more often than not will do the same thing


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Normal light flashing on and off. Pressed cancel, now both normal light and cancel light are flashing. Dishwasher won't start. Can't shut lights off. Tried disconnecting power. Lights still flashing.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To resolve this you will have to\015\012reset the console. Do this by closing the door and press t ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Kenmore Dishwasher - Flashing Lights - wont start


Is the clean light blinking 7 times? If so this means you have a problem with your heating element ... Kenmore 15899 Built-in Dishwasher

Control lights are flashing, normal wash, rinse only and cancel...will not let me start dishwasher, will not let me choose heavy wash, shut off fuse, it reset and went on for about 30 seconds then canceled and starte lights flashing again...


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1176 seconds