Having problems with your KitchenAid 24 in. KUDU02FR Built-in Dishwasher ?

Normal, light rinse and cancel button are blinking. Turned breaker on and off with no change. Took panel off and tech sheet to give the codes was not there so don't have it. Repairman with no tech sheet says need new control panel. Is there any way to get the tech sheet online to reset and see if problem persists. Kitchenaid kudu02fr The unit is 4 years old.


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Normal, light rinse and cancel button are blinking. Turned breaker on and off with no change. Took panel off and tech sheet to give the codes was not there so don't have it. Repairman with no tech sheet says need new control panel. Is there any way to get the tech sheet online to reset and see if problem persists. Kitchenaid kudu02fr The unit is 4 years old.


... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

Intake drain flashing - but this time because water is not filling. Checked voltage at controller board - inlet solenoids are getting 120V intermittently. I found online that this is the behavior for fault code f12. But my machine does not give fault codes directly - is there a way to get it to "blink" them?


... Miele 24 in. Incognito G843Vi Built-in Dishwasher

The Bosch plastic push button (AP2804452) has broken on my SHU9950 dishwasher. The switch itself is still good. I have removed the broken pieces of the bad button from the unit and am now depressing the switch without the button. When I get the new push button, what is the proper way to remove the control panel cover to put the new button in place? Thanks!


... Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Dishwasher I am getting a run around with getting my LG dishwasher fixed properly. We had a tech more than once come in and look at our dishwasher. It has not been fixed and never dried the dishes properly. It is now leaking and going to a "del" level when we attempt to wash the dishes. It is also leaking on our fairly new tiled floor and under our new kitchen cabinet. Your tech stated the dishwasher was not installed properly. The installation dept , Francine stated it is not their problem


Not sure what you mean by a "del" level, but as far a drying issues:\015\012\015\012LG chose to use a very energy efficient drying method which relies on the residual heat of the dishes to help dry them rather than many manufacturer ... LG LDF6810 Built-in Dishwasher

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

I am not happy with the racks in my new Bosch dishwasher! The bottom rack is not right! The silverware basket is in the back right corner and the silverware catches on the seal on door and it is hard to get to. The tongs are two close together and point the wrong way? The upper rack's tongs are also to close together also. I don't seem to be able to get larger dishes in with these tongs in the way. Having never used the mdl 9000359119 Rev B I had no idea. Buying a Bosch ment quality to me


... Bosch Dishwashers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

I have a whirlpool A class ADP 4305 electronic control dishwasher that has a blinking light(seven times) at a time. There is no tech sheet in the door. i have opened the front pannel.But no tech sheet?


... Whirlpool Dishwashers

MDB6709AWW1 Poor Quality Control Panel Our dish washer is 2 years old this month and the control panel broke!!! My service technician told me that he has seen DOZENS of new Maytag dishwasher control service panels break and is convinced it is a design flaw. When I called Maytag the customer service rep had the NERVE to tell me "that because the house is near the beach, I must get a lot of power outages and power surges, that is why the control panel broke." I told her I wasn't born yesterday


... Maytag Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Fitted New Dishwasher Control Panel - Need reset sequence


One likely cause you can try first is to disconnect it from power via the cord or a breaker. after a brief period, it may reset itself.otherwise you likely have a logic board issue.logic boards seem to be very vulnerable in dishwasher env ... GE Profile PDW8400J Built-in Dishwasher

DU1100xtpt6 stopped working - blinking clean light. Reapir tech says needs new logic board and heating element. Says logic board is under warrenty... can I get board from whirpool with out tech? Where I can buy correct heater? thanks!


If you have "good hands" and a technical orientation, you can manage it by yourself\015\012(board and heating element).\015\012In any case, before buying a new heating element, check element's resistance with a multi-meter, maybe there is no problem ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Bosch Dishwasher has error code e24, I checked the line, replaced with new pump, new control unit and call repair man no luck. It works on and off. I get it run then next cyle nothing. Heelp!


... Dishwashers

I have a Kenmore Elite Ultra Wash dishwasher. Model #17572. All the lights on the control panel went out. Get no response at all. Circuit breaker is fine. Any reset tips? Or, do I need a new control panel?


... Kenmore 24 in. 17572 Built-in Dishwasher

Have a Kenmore Elite Dishwasher (66513123K701). Was not cleaning dishes very well so we ran diagnostics on it and found a problem with the diverter motor (W10155344) so we replaced it. Now, the dishwasher is leaking from the diverter. There was a o-ring from the original diverter that we had to keep since the new motor did not come with it. Wondering if we should get a new o-ring/seal, but I cannot find mention of such a part anywhere. Is there a certain way to seat the o-ring? Is it ok to


I have experienced the same diverter motor leaking problems. I have the whirlpool gold with the diverter motor (w10155344). I bought the unit new 4 years ago. The fix is remove the the two screws that hold the diverter motor and pull the motor. ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

We have a GE profile dishwasher that will not drain. We have replaced the keypad control and control module and it still will not drain. When we put it in service mode, we can get it to drain that way but when it is taken out of service mode, it goes right back to the same problem.


Its the timer issue:--\015\012what the timer does is control the motor and drain valve. If the timer doesn't work properly, the water may not drain and you need to replace the timer. This problem is common. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Hi I have a maytag quiet series 300 with model # MDBTT60AWW and it will not start. All the lights lite up but it will not start. I recently just had to replace an element due to a recall so when he was hear fixing the element I asked him what he thinks could be the problem and he said it sounds like it possibly needs a new control panel. Does this sound right and if so do you know where I can get a control panel. Thanks for your help


... Dishwashers

Whirlpool GU1500XTKT0 dishwasher has a Rinse only led blinking. No functions are responding on the control panel. Keyswitch resistance check table on Whirlpool Service Technician's Tech Sheet checks good with digital multimeter. Door switches and thermal fuse near control module check good.


If your keypad tests, door switches, and thermal fuse are all good, the only test left is to make sure you are getting 120 volts at your control board. Test for 120 volts at terminals p8 and p7, and at p2-6 and p7. You will have to activate the doo ... Dishwashers

Bosch SHU43C Dishwasher. Where to get parts - quick? Needs a new control-board / circuit board. All valves, switches, heater appear to work. Won't run open the water inlet valve. Won't run the self-check program. Has a burnt connection on the control 'mother-board'.


1-800-944-2904 That is Bosch Company. They will send out-- next day. ... Bosch 24 in. SHU43 Built-in Dishwasher

Control Module? I have a GE Profile that seems to have a control module issue. I've changed the module and it continues to do the same thing...won't drain at end of cycle and begins washing right away after selecting new cycle. Washes for only about 5 minutes total and then just heats the water...soap dispenser doesn't get rinsed clean either. Any ideas?


... GE 24 in. PDW9880LSS Stainless Steel Built-in Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1289 seconds