Having problems with your KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher ?

Model # KUDP01FLSS5 Dishwasher has power. Normal button lights up but start button wont light and wont start dishwasher


Answers :

Please check the internal connections.
Repair Help & Product Troubleshooting for KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model # KUDP01FLSS5 Dishwasher has power. Normal button lights up but start button wont light and wont start dishwasher


Please check the internal connections. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Kenmore undercounter dishwasher model 66517019400 wont start..I want to purchase a new control board do you think this is the problem? normal cycle light comes on, cancel button works, heat on button works, just wont start ??


It might not start because the water solenoid is failed, or the water level sensor is failed.\015\012\015\012You have to use a meter to test these components first. Put your voltmeter on the two leads going to the water solenoid, and psuh ... Kenmore Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Whirpool Dishwasher ADP5966 Turned dishwasher on. Only light that comes on is normal wash light. Start button is flashing when normal wash light is on. On pressing start button dishwasher does not work


Most likely the door switch is not making proper contact when you shut the door or the Start button is faulty. Needs someone to look in the door panel to fix. ... Whirlpool Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Last night i loaded my kitchenaid KUPD01FLBL2 dishwasher, hit the normal button (green light came on), pushed the start button and went to bed. This morning I opened the dishwasher and it had not run. I tried again, Ihit cancel and then normal and start again. Would not start. Help?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My Maytag MDB7609awb2 dishwasher has a glitch When I try to turn it on the heavy and light was lights go on but won't start the normal wash light won't go on at all until I keep pushing the off and on for a while, then suddenly the normal button works and start will start the machine, then is washes without any problem.


... Maytag 24 in. MDBH955AW Built-in Dishwasher

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Kitchen Aid KUDIO1ILBS5... Normal Light keeps flashing green and wont start. When I press the cancel button, it flashes too. If I hold down the cancel button fashing light goes away on cancel button, but not the normal button... It continues to flash.


Hi,\015\012\015\012Close the door and to cancel that just press high temp and hetaer dry,then again high temp and heater dry and all the lights is going to light up, it getting into test mode.After that press cancel.\015\012 ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Vdb450ss The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again


... Viking DFB450 Dishwasher

Frigidaire dishwasher does not start. but i see the cycle select LED light come on . all of a sudden the dishwasher stopped working. all buttons except the "start" work. i can select 'normal', 'pots n pans', select the delay etc, but the START button will simply not work!


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2443 seconds