Having problems with your KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher ?

Kitchenaid dishwasher # kudp01flss doesn't power on . Checked the unit is getting power from the outlet.


Answers :

There is a thermal fuse located inside the control panel of the dishwasher. The part number for the thermal fuse replacement kit is 8193762.

There were some noted problems with certain model dishwashers where the wire gauge on the thermal fuse was too small and would heat up causing the thermal fuse to blow prematurely. The replacement kit includes a wire harness with a larger gauge wire that you simply splice into place with the new thermal fuse. It handles current better and prevents the fuse from blowing prematurely. To ease your mind, there were no reports of fire hazards.

If you type in your model number you can utilize the exploded view parts diagrams at pcappliancerepair.com, appliancepartspros.com or searspartdirect.com to assist you in locating the part. The fuse is listed as item 6 under the "Control Panel Parts" section. I found the listed listed for the best price at appliancepartspros.com and comes complete with instructions as well.

To replace the fuse, follow these steps:

1. Make sure the dishwasher is unplugged or the breaker is turned off.

2. Open the door and remove only the top screws directly behind the control panel.

3. Remove the protective cover from back of the control panel to expose the main control board.

The thermal fuse should be mounted to the control board. If you remove it and take a resistance check, it should read close to 0 ohms, if good. If bad, replace as necessary.

If you have any questions about this repair, or require additional assistance, please let me know. I hope this helps you.
Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working--
\015\012\015\012
\015\012\015\012
\015\012\015\0121. Fuse (blown or tripped).
\015\012\015\0122. 120 VAC supply wiring\015\012connection faulty. Repair or replace wire fasteners at dishwasher junction box.
\015\012\015\0123. Electronic control board\015\012faulty.
\015\012\015\0124. Motor (inoperative, check\015\012resistances).
\015\012\015\0125. Door switch (open contacts).
\015\012\015\0126. Door latch not making contact\015\012with door switch.
\015\012\015\0127. Touch pad circuit defective.
\015\012\015\0128. No indicator lamps illuminate\015\012when START or OPTIONS is depressed.
\015\012\015\012
\015\012\015\012
\015\012\015\012Please do accept the solution if the issue is resolved or\015\012else revert for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kitchenaid dishwasher # kudp01flss doesn't power on . Checked the unit is getting power from the outlet.


There is a thermal fuse located inside the control panel of the dishwasher. The part number for the thermal fuse replacement kit is 8193762.There were some noted problems with certain model dishwashers where the wire gauge on the thermal ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

No power My dishwasher Model DMR77 quit working yesterday during a wash cycle. No power ie, no display light or tones. I am getting power to the unit, checked with a volt meter. I am thinking Power supply, or is there a reset on the unit.


Hi,\015\012 The main PSU is part of the control board. You may be lucky to find an aged fuse to replace, but it's more likely a power transistor that's fried.\015\012\015\012Unplug and remove the control board to see which bit's toa ... Samsung DMR77LHS Tall Tub Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

8575637 Brand new dishwasher installed about a month ago. Its been used about 10 times and in the middle of a wash cycle, completely stopped with no power. Have checked the plug, outlets, breakers. Cannot get any of the buttons to light up, have checked to make sure it wasn't locked out - no power at all. Manual is not helpful. Any ideas?


... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool dishwasher Model#GU3200XTPS0 No power to unit, Control panel does not have power check the circuit and outlet, are OK. is there any fuse inside the unit? is circuit board has any fuse?


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

AEG Favorit - model F86050UM The dishwasher was disconnected and moved whilst new timber flooring was being laid. On reconnection it was evident there was some water in the base of the unit, this was removed by tipping the unit over to drain. Now there is no power display on the door.Power outlet checked OK. Your assistance would be appreciated in this seemingly simple problem. Murray


What has happened is that you have tripped the overflow/anti flood device switch when you upended the machine. You most likely need to empty out the salt container, and to reset the antiflood give the machine a few sideways tips and try to shake fre ... AEG Dishwashers

My Kenmore Ultra Wash Dishwasher model 17731 stopped working mid wash I checked the power cord and it is fine but the unit doesn't seem to be getting power. Is there a fuse in this thing? Any advice would be welcome.


... Kenmore Dishwashers

My Smeg Dishwasher (DIG12CA) is just 12 months old. It's as if there's no power getting to it. I have checked all external fuses and power is reaching the unit. Any ideas on what could be wrong? AG


... Smeg Dishwashers

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Whirlpool dishwasher DU1015XTXBO Stopped working during cycle, acts like don't getting any power. Checked the plugin and it works. No lights or anything coming on the dishwasher. Its like it just


... Whirlpool Dishwashers

I am not getting any power to my dishwasher? Checked the breaker, the outlets. all good there


You need to take the very bottom panel off the dishwasher. This panel is located at the floor and is held on with 2 philips head screws once the panel is removed look for an electrical plug located under the dishwasher(use a flashlight for the best ... Dishwashers

I have a KitchenAid Dishwasher KUDIO1iLBS2 and none of the lights come on and if I press any of the buttons nothing happens. The unit is getting power to it as I shocked myself. I did ordered and replaced the control board and still nothing is happening. Any suggestions or ideas? Is there a reset button or is there a possible fuse that is out that would make the lights not come on? Please help.


... KitchenAid Dishwashers

Maytag 6 yr old Dishwasher - Model LR111721 Standing water in bottom of unit. Front panel lights do not come on. Checked circuit breaker in basement & it is getting power. Last time we used it it seemed to make a bit more noise than ususal.


... Maytag Dishwashers

Our dishwasher doesnt seem to be cleaaning the dishes properly. After the cycle soap residue remains on the door and bottom of the unit and the dishes are not getting clean. I have checked the supply line and discharge for blokage but both are clear. what should I be looking for?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

My Samsung DMR77LHS dishwasher has lost power completely near the end of a cycle. About an inch of water remains. I have power to the unit. I checked the 15 amp fuse in the unit - it had blown. I replaced it, but still no luck. The fuse is not blowing, but there is no power to panel. Nothing happens when you hit the power button - no lights or anything. Unit acts as if ther is no power at all. I have seen similar posts. Any thoughts?


Hi, whenever a fuse of that magnitude, or any fuse really, Blows, you should never just replace it, as to have any device, blow a fuse, trip a breaker, requires a major fault, they do NOT blow spontaneously ever. So you have had a major short circu ... Samsung DMR77LHS Tall Tub Dishwasher

Kenmore dishwasher I have a kenmore dishwasher and in the middle of a cycle all my front panel lights went off. I have checked the power going into the dishwasher it is fine. I also checked the door latch it is fine. Not sure what else to check? Same exact problem model number 665.15934 We have had nothing but problems with all of our sears products - highly suggest to SHOP SOME WHERE ELSE before you get stuck too.


Check the continuity of the thermal fuse (part # 8193762). It's clipped onto the electronic control inside the console.Let me know if you need more help. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2651 seconds