Having problems with your KitchenAid Architect? II K SERIES KUDK03IT 24 in. Built-in Dishwasher ?

My Kitchen aide dishwasher doesn't seem to be spraying water during a cycle. It fills with water but that seems to be all. also is there some where that I can go to get a trouble shooting manual


Answers :

This could be due to the sprayer arms not moving. Try to get these out and clean them. If the holes are blocked these will not move.
\015\012
\015\012You might find the correct manual for your model at this site
\015\012
\015\012http://shared.whirlpoolcorp.com/product_literature/search_results.jsp?searchTerm=KUDk03it&siteCd=KAD
\015\012
\015\012It appears this brand is made by Whirlpool.
\015\012
\015\012Hope this helps.
The chopper sceen gets pluged and wont pump good.it's kinda ticky to get to you will need #15 torx bit to remove grab center of the spray arm and twist til arm will lift out, the tube going from center to back twists clockwise careful not to break it, take all the screws out of cover and take it out. in the sump tward front left down in bottom is 1 more screw if you have a wet vac or turkey baster to get water out to see it. it holds down a half round lift straight up you will see the screen clean it out and put everthing back
Repair Help & Product Troubleshooting for KitchenAid Architect? II K SERIES KUDK03IT 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kitchen aide dishwasher doesn't seem to be spraying water during a cycle. It fills with water but that seems to be all. also is there some where that I can go to get a trouble shooting manual


This could be due to the sprayer arms not moving. Try to get these out and clean them. If the holes are blocked these will not move. \015\012\015\012You might find the correct manual for your model at this site\015\012\015\012 ... KitchenAid Architect? II K SERIES KUDK03IT 24 in. Built-in Dishwasher

Hi I have a Blanco dishwasher BFDw8 which is having poor wash results in the top tray I have tried all the trouble shooting things in manual. Investigated further by opening door during wash cycle several times and discovered the top arm is not moving although water is still coming out of the arms. I did get a split pea particle out of the arm approx 2mm and have since had a mildly better wash and have used superior wash powder and rinse aid to try and help. Also have put a cleaner through di


\015\012\015\012Check the water temperature. Should be 125 to 140 F. \015\012\015\012Check pump re-circulation., Listen, see if it sounds like it is spraying the water around with enough pressure. ... Dishwashers

I HAVE A BRAND NEW BOSCH MOD.SHE4AM12U DISH WASHER IT START TO FILL WITH WATER,THEN STOP AND NOTHING ELSE HAPPENS,CANT GET IT TO START THE WASH CYCLE.IS THERE A REPAIR MANUAL OR SCHEMATICS THAT I CAN OBTAIN TO TRY AND TROUBLE SHOOT THIS UNIT,I WORK WITH ELECTRICAL APPLIANCES AND I AM QUITE KNOWLEDGEABLE WITH TROUBLE SHOOTING.THANKS


... Bosch SHE4AM12UC Dishwasher

I have an older (appx 20 yrs old)GE model 2200 dishwasher and recently started getting a C5 error. I understand the water input valve may be plugged. I don't have the owners manual. Where can I get one to locate the valve and strainer so I can trouble shoot this problem


Go to marcone.com, enter your model # and it will give you a full breakdown of the unit ... GE Nautilus 24" Built-in Dishwasher

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Waterintake stops after approx. 35 sec.waterlevel is to low,detergent compartement will not open because of low waterlevel and also water will not heat, because heating element is not covered with water. If I put water in by hand to get the waterlevel above heatingelement everything is fine. Dishwasher has been working without any problems till approx. 18 mths ago. Have also adjusted waterintake time as described in manual by taking off dial knob and adjusted with small flat skrewdriver, but not


The machine fills by time only as you have already determined. The intake screen on the water valve is probably plugged up and cleaning it should solve your problem. You will have to turn off the supply to the dishwasher and disconnect the water feed ... Dishwashers

Glasses and others things are not getting clean in the upper rack. A white film remains on the glass and stains are not removed. Also I'm having trouble with the silverware showing rust spots and not getting clean. I use Jet- Dry all the time. We bought it three years ago. The brand is JDB-5 and numbers inside the door are: JDB1270 AWY 36072124 LC MAX LOAD CHG 9. made in Newton, Iowa. We have had trouble with things not getting clean for quite a while, but it has gotten worse. The water is scald


If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is toadd some vinegar to t ... Jenn-Air 24 in. JDB1270AW Built-in Dishwasher

Our Bosch SGS 53E02 AU/30 Dishwasher has the Tap Light on all the time while the Dishwasher is filling up. It appears as though water cannot get through and takes a long time to fill. It also does not allow the wash cycle to start and the powder door does not open. Can you also get any Service manuals for this model?


... Bosch Dishwashers

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

Jenn-air dishwasher JDB-5 (jdb1105awb) will not drain. Have repeatedly prompted drain cycle (start/cancel twice) there is what seems to be a pump noise for a minute or two, but no water flow noise and water level is the same in the bottom. The manual is sparce on trouble shooting and schematics. I suspect something is clogging the drain path. No changes to the drain hose routing. Machine has been installed for three years with no major issues. What is the recommended disassembly sequen


... Jenn-Air JDB6510 Built-in Dishwasher

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a G E Nautilus dishwasher that has been in storage for 2 years. Every thing works but the Drain. When the cycles are finished I' m left with a dishwasher full of water and it dont drain. I checked the bottom as u said in a previos question I see not obstacles, trash etc. How else4 can I get it to unplug? Also where can I get a owners manual? I can be contacted at [email protected] if needed. Thanks ahead of time for the help.


Hello. Here is the link to a free manual http://kitchen.manualsonline.com/manuals/mfg/ge_appliances/ge_ap ... Dishwashers

When I start the wash cycle it does not get any water, but will continue through the entire cycle. I have checked and replaced the water valve, check teh float and float switch. The handle is working correctly. The selector panel is all elcetronic and I do not know what else to do to trouble shoot. Any help??/


I would first check the water valve is it turne on? then are you getting power to the water valve ? if not problem might be in electronic panel. ... Dishwashers

I have a dishdrawer (2) and following the use of a dishwasher cleaner, the bottom drawer appears to have developed a blockage. It will not empty, gets to the pump out part of the cycle and shows the red error code F3, to which there is no reference in the trouble shooting guide. The top drawer has also developed minute leak, sufficient enough to leave dribble marks on the lower drawer and over time, a white deposit on the floor. Is there anything we can do for the blockage problem before reso


Remove the small basket from each drawer and lift up the removable plastic cover and take the drain filters out , empty them of food by products and try it again.. If you've never cleaned them then that's your problem with the drain process.. Hope th ... Fisher and Paykel Dishwashers

I have just had a CDA WC430IN Dishwasher installed. I have followed the instruction manual regarding what to do when you first use it. Unfortunately it runs for around a minute then beeps 10 times and has four lights flashing. The trouble shooting guide doesn't show what this means. I have checked that the water is on can you help?.


I would called the people who you bought the dishwasher off of and let them worked on it. There should be at least a 90 days warranty on parts and coverage. ... Dishwashers

When the dishwasher stopped there was about 2 inches of water left in the machine. Trying to start it again is met with an A-3 fault message...this does not appear in the manuals trouble shooting section!


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Dishwashers

The top rack isn't getting clean. Is it needing something cleaned out, or is something not sealing and taking the water pressure up to the top rack? How do I trouble shoot this. I already tried running an empty load with white vinegar...


Good evening. The white vinegar was a good start. It may not have helped the problem described, but will help clean out the lower end of the unit. Look for plugged nozzles and slots on the arms. Remove the arms and wash backwards through th ... Maytag 24 in. MDB6601AWS Stainless Steel Dishwasher

Bush dishwasher model wqp12-9348 not draining away fluid and seems to be blocked which is making water leak over floor. Cant find instruction manual to trouble shoot. Think it might be food residue or oil? will salt help?


... Bush Dishwashers

What does the code NE mean on my LG dishwasher? it gets through about 10 mins of a cycle then bleeps and the code NE is on the screen. I tried putting it on a different cycle and starting again but the same thing happened. ive only had this dishwasher about 5 week, i checked the manual for the code and it isnt listed among the trouble shooting codes there


... Dishwashers

I have a Blanco Dishwasher Model BFDWC65X. It appears that the thermostat may be faulty as the water gets extremely hot on cycle 3 which is supposed to operate at 45 degrees centigrade. When I open the door mid-cycle, clouds of steam emerge and the whole dishwasher smells hot - almost a burning smell. I have found an online source for a replacement thermostat, but would like to know how difficult a job it will be to replace the thermostat. Also where can I find a manual that details where the th


... Dishwashers

Hi, i have a Miele G 693 SC plus which had the red light lid up: evacuation problem or entry of water, how can I solve this problem ? Furthermore I have tried to download a manual to try and find a trouble shooting diagram, I have spend an hour through a site "devicemanual" without any luck, Does Miele have a simple site ? for this, thanks - Peter


Hi,this is a general fault light which could mean anything without a Miele Technician coming out and connecting a laptop ... Miele G892SC SS Dishwasher

I have karcher k4.98. I can not get the detergent to come out. I have checked the trouble shoot in the manual and all items are ok. Any ideas ?


Just had the same problem, brand new machine, the detergent feed pipe was squashed under the bottle holder bracket! ... Karcher Pressure Washers

Pld4555rfc3 Frigidare 4000 series aquaSurge w/speed clean. Model pld4555rfc3. Recently noticed soap residue left inside cups on upper rack. After trouble shooting I found that water is not getting to the two upper spray arms. Could there be a clogging issue in the housing or pipe?


Hello ddux97 - Here are a few simple troubleshooting tips\012that may help you resolve this issue:\012\012\302\267 \012Do you have hard water? Hard water is the primary\012reason to cause soap residue. Water hardness can be deter ... Frigidaire PLD4555RFC Dishwasher

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1655 seconds