Having problems with your KitchenAid Dishwashers ?

Just had our kitchenaid dishwasher installed yesterday, I noticed that the bottom rack when filed with dishes is very hard to push back into the washer. I think it is to low to the water dispenser on the bottom.


Answers :

Pull the rack out of the machine. Make sure all the wheels are on it. Put it back in and see how well it rolls in and out, the wheels should roll on the top of the rail, checking that it is not draggin on anything. Don't overload it with heavy items, it does have a weight limit but don't know what it is.
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just had our kitchenaid dishwasher installed yesterday, I noticed that the bottom rack when filed with dishes is very hard to push back into the washer. I think it is to low to the water dispenser on the bottom.


Pull the rack out of the machine. Make sure all the wheels are on it. Put it back in and see how well it rolls in and out, the wheels should roll on the top of the rail, checking that it is not draggin on anything. Don't overload it with heavy items, ... KitchenAid Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

Dishwasher bubbles I have a kenmore elite mod- 16599201 stock # 16599 , recently there has been bubbles in the washer after the wash cycle ends . I thought that I might of put detergent in the jet dry hole so I removed the dispenser and rinsed the whole thing completely clean and reinstalled it. but the bubbles are still there . I think its the jet dry not completely rinsing away. I cleaned the dishwasher with vinegar and then glisten. My water temp is slightly low as I have my water heater set


... Dishwashers

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Hi my L G dish washer is coming up with E1 . It comes on after about 2 min it takes water into the washer then it hummes for about 30 seconds then comes up with E1 and pumps water back out. I have checked the hoses which don't appear to be leaking -I read somewhere in your answers about this problem that it could be the Water Level in Drum lowering, this means there is a leak on one of the pipes. More likely it is the Circulation Pump, which is responsible for pushing the water to the Spray


Hello aderry -\015\012\015\012\015\012I'm a bit short of time as I'm on my way out to a service call, but I've uploaded the service manual to Rapidshare for you to download. \015\012\015\012\015\012Rapidshare download inst ... LG Dishwashers

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

GE TRITON dish washer. Utensils are stained after wash. I tried all that suggested solutions like cleaning with white vinegar, make sure hot water flows before it starts. I donot think we have hard water problem and also tried Jet dry rinsing. Nothing is working still i see utensils soap stains and not completely rinsed. I am desperately looking for an answer. I am thinking of is there a way i can test whether the middle tower is really opening up to spray water or not. It might be something els


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Maytag Dishwasher

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

My bosch dishwasher runs fine, cleans fine, drains fine....but after it has been just sitting for a while, the bottom very slowly fills up with water. Each time we run the machine the water level drains back to the normal amount in the bottom of the washer after the cycle is complete. The problem is if we are away for a few days, the bottom fills up and overflows onto the floor.


Water inlet valve isn't closing all the way closed. Need a new one ... Bosch 24 in. SHU53 Built-in Dishwasher

My Asko D1976 dishwasher is not cleaning dishes properly. There is a lot of clumped detergent left in the dispenser after wash cycles are complete, and many of the dishes have dried-on food left on them. I rinse dishes before loading them into the washer, I have made sure the jets and washer arms are clean, and made sure the food trap at the bottom of the washer is empty, yet the problem persists. I think it has to do with the detergent not dissolving and dispensing. Is there some reason the


First of all, don't pre-rinse the dishes. Check the water temperature, it should be between 120 and 140 degrees. Be sure you are not partially blocking the dispenser door so that it isn't opening. ... Asko D1976 Built-in Dishwasher

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

The insultation on the bottom of the door is wet. My repairman said water is getting behind the soap dispenser and the rubber gasket around the dispenser is hard. The dishwasher is only 4 years old. Is this possible. The insulation at the bottom of the door is wet. Oddly, this is an intermittant problem. The past two days, with a small load of dishes, there was no leak. Help!!


A reader on another forum found, after much effort, that the solution may be very simple: don't load flexible cutting boards on the right-hand side of the machine.The boards can block an outlet on that wall, presumably leading to a buildup ... Bosch Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

Turns on, the entire cycle runs, but no water pumps through the sprayer. There is water present on the bottom....and I can here the water pumping in at the beginning of the cyle....but the dishes are not being 'washed' by the sprayers. I have disassembled and cleaned the entire inside and sprayers to no avail. Im thinking its a pump/motor issue but Im not sure because the sprayers spin, the heat comes on, the detergent dispenses....but no water is being sprayed. Thanks.


Yes i agree, your pump is not working as it should. J.\015\012\015\012That said if this machine is over 3 years old, replace it. The new ones are so much quieter, better, and cheaper to operate. J. ... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

Whirlpool GU1100XLTQ1 dishwasher, 4 years old is leaking water during cycle. I cannot see exactly what is leaking by looking up through the acess panel in front...there are what appear to be plastic support ribs for the tub and water is leaking through several of them to the left of what appears to be the motor in the center...please help! I don't think I can run the washer and tilt it back at the same time as the water supply line only allows me to pull it out just enough to clear the counter t


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wahgfadh ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

I have a whirlpool gold model GU1500 diswasher. When the rinse cycle ends the water pumps out into the garbage disposal like it should, but then water backs-up from somewhere into the bottom of the dishwasher. The overfill protection drain seems OK...the water doesn't overflow. It doesn't have a air gap on the sink. The drain hose goes directly from the dishwasher to the inlet on the garbage disposal. It appears to be properly installed per the installation instructions. The washer is about 4 ye


Seems you answered your own question here. You need to make an air gap in the drain hose - take as much slack as possible and make a curve (upside down U) under you sink as high as you can go. Make sure you clip ot to back of the cabinet to stabili ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to


Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2104 seconds