Having problems with your KitchenAid Dishwashers ?

LOWER WASHARM AND STRAINERIS NOT RUNNING &MOTOR IS RUNNING BUT NO WATER IS UPLIFT


Answers :

On the end of the motor is an impellor the impellor threads can get stripped resulting in poor or no washabilaty
\015\012(solv ya prob)
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

LOWER WASHARM AND STRAINERIS NOT RUNNING &MOTOR IS RUNNING BUT NO WATER IS UPLIFT


On the end of the motor is an impellor the impellor threads can get stripped resulting in poor or no washabilaty\015\012(solv ya prob) ... KitchenAid Dishwashers

Pump to discharge water is underpreforming. won't empty standing water in bottom of unit when cycle is over. will dichsrge water when dicharge tubing is lowered to downhill slope. can hear motor running


Disassemble the drain and pump area, you will mostlikely find particulate matter restricting flow. ... KitchenAid Dishwashers

My maytag dishwasher lower and upper spray arms are working intermittently. Sometimes there is plenty of water spraying around, other times, I can hear what sounds like the motor running but the arms are not moving (or not moving much) and very little water is splashing around. When this happens, the detergent sometimes doesn't even get washed out of its compartment.


Pour 1 Cup of Muriatic Acid (Can be purchased at your local Pool Supply Store) into the bottom of the washer and a little in the soap dish. Run the Dishwasher through 5 cycles. Check to see If this helps. If not Try the same process with CLR house cl ... Maytag 24 in. MDB4000 Built-in Dishwasher

Sat up for a year or more changed oil in pump and motor , new gas motor runs fine but notbgetting water pressure its the 2500hpw and weter is spurting out of a red plastic fitting on the lower pump case


... Northstar Pressure Washers

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

Motor runs continuously. No water in lower pan.


Hi,Here is a tip that I wrote about that....http://www.fixya.com/support/r4021363-dishwasher_trouble_no_water_entering ... Asko D3531XLHDSS Stainless Steel Built-in Dishwasher

My RMW 2.2G24 will not discharge water once the motor is running. When motor not running the water will flow through. It also appears the pump locks up every now and then becasue I cannot pull to start the motor. Bleed pressure and motor will start.


... Annovi Reverberi RMW2.5G25D

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

My Troybilt pressure Washer Model 020207. runs forabout 30 seconds then the motor stops. Acts like motor is locked up. Motor can't be pulled until water hose is disconnected. Took the water pump off and the 6.75 Briggs starts and runs like new. What could be the problem.


It sound like a digafame problem/or/carborater bowl has some water or needel valae is sticking cheack them if not the problem then you may have a crank shaft problem good luck see if there is oil in motor ... Briggs & Stratton Pressure Washers

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

Honda 3540CWHP cannot get water to spray with or without motor running. I have cleaned the filter and motor runs fine still no water? Help! Gary


... Pressure Washers

Won't start After two months of no use my dishwasher won't work. I can hear motor running but no water. We tried cleaning by filling with water (priming motor) but nothing happens. Now the dishwasher if full with water, motor makes noise but nothing is happening. Help!!


It sounds like you have a food blockage or some blockage between where the water fills up and where it goes into the pump you need to take out the water wand (the rotating thing with water coming out) only the bottom one. You need to unscrew the wate ... Hotpoint 24 in. HDA1000Z Built-in Dishwasher

Maytag DWU6402AAB dishwasher hums but motor does not run. I've taken the inside apart down to the disk-shaped impeller. It turns freely so the pump and motor are not stuck. When control knob is turned motor hums at the places where it normally should run. The water valve & heating coil seem to be operationg normally. i assume the next step is to test the motor &/or motor relay. Is this correct and how do I do that?


... Dishwashers

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

My karcher k2.180 is surging when water and motor turned on. I've disconnected the hose and water is flowing and the motor running smoothly. However when I've reconnected again the motor is


... Karcher K2.26 Electric Power Washer

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

My sound conditioned Whirlpool dishwasher is real old. It fills up completely with water. It looks like it will overflow, so I stop it. I thought it always started washing from the start. Do they always fill completely up with water, then start washing. I never noticed. I am afraid the water will overflow. Can it? Last time I ran this, it had a real loud motor. I used to hear the motor running from the start, but now I don't, just water filling up to what looks like overflow if I let it. I baile


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Hear the motor running, no water in dishwasher


I thought I would fix this myself - but hubby took a look, wiggled a few wires and said 'there's your problem'. The water valve would not open because a connecting wire was loose. It was the kitten after all - I'd better pop that panel back on. ... Maytag MDB9600A Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1609 seconds