Having problems with your KitchenAid Dishwashers ?

I have a Kitchenaid dishwasher model KUDS01FLSS2. I finished replacing the door balancer cord and started the dw up and it started leaking underneath from the bottom somewhere around the middle of the unit. This is when it first enters the cycle, so there is no water inside. I pulled the DW out and look at the hoses and components under the DW and all looks in good shape and could not detect any cracks. However noticed that one of the hoses (not sure what the hose is called) that connects to the


Answers :

In this Kitchenaid dishwasher model KUDS01FLSS2, the whole motor and water pump assembly simply sits (I think loose) in the bottom of the DW. From the inside, it is the round mechanism where the sprayer is mounted above the chopper, all one piece sitting in (or mounted with) a large rubber washer around it. Somehow this assembly had lifted up slightly on one side which allowed the water to just poor through the bottom floor of the DW. I simply pressed down on the whole mechanism positioning back in its proper place. It did not take much pressure at all to position it back into its place. This stopped the leak and is working like a charm.
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kitchenaid dishwasher model KUDS01FLSS2. I finished replacing the door balancer cord and started the dw up and it started leaking underneath from the bottom somewhere around the middle of the unit. This is when it first enters the cycle, so there is no water inside. I pulled the DW out and look at the hoses and components under the DW and all looks in good shape and could not detect any cracks. However noticed that one of the hoses (not sure what the hose is called) that connects to the


In this Kitchenaid dishwasher model KUDS01FLSS2, the whole motor and water pump assembly simply sits (I think loose) in the bottom of the DW. From the inside, it is the round mechanism where the sprayer is mounted above the chopper, all one piece sit ... KitchenAid Dishwashers

I have a new LG Dishwasher LD120W1 purchased on 6/11/09. Have only used it approx 3 times. When I turned it on today it started up and after a few minutes it starts whistling and does not fill. Have looked at filter and spray arms, all clear. Could you please advise what else to do or look at. I can pull it out to look at hose it was installed by a plumber.


Hi,I would Glad to tell you what needs to be Done!! But, as the Dishwasher is Under Warranty, give them a call. Why to spend any Money, when the washer is under Warranty :) Now, It sounds like a Water Pressur ... LG Dishwashers

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

After 3 years it just started making a loud noise, I am no expert but it sounds like a fan in a motor. I have only heard it today, but I am betting it will still happen next load too. I didn't change any of the settings, have been running the same way forever. When I did hear this noise I started pushing buttons to see if I could get it to stop, no good, no change. The cycle has completed and everything looks ok, waiting on the dishes to dry. Drainage has never been a problem for me either.


I would say this is a build up of lime.try changing your tablets and checking your salt levels.there is no fan .try what i say and see what happens.have you found a glass broken it could be as simple as that but i dont think its serious.adrian,,,, ... GE Nautilus 24" Built-in Dishwasher

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

My Professional series model fdbb4365fc2 Makes a slight intermittant thumping sound a few times when its started and than after a few moments it shows the error code uo. For a while we could cancel and try a different cycle and it would work. I checked drain hoses and sink trap all looks o.k. What is my options


... Frigidaire Dishwashers

Water stays in the top draw filter area, have checked hoses found good connection and no kinks in the lines , could this be a pump motor problem. I have had a problem the first month with this unit and the tech. replaced a lot of parts including the computer for the top draw . i am now out of warr. time not by much and am starting to get upset that this problem is happening after such a short time.


... Fisher and Paykel DS605I Built-in Dishwasher

We have a Bosch dishwasher SHX46A06 UC/21. It continually runs. We couldn't find a diagnostic test for our model, but we did for another model. We held down the power scrub and regular wash cycles then turned it on and pressed them again. The delicate/econo light started blinking. Looking at some of the blogs, most often it seems to be the heater or the control panel - does this diagnostic test help to pinpoint what could be wrong? Also, where can we find a good manual for our model - we're havi


Here is a link to the service manual http://cgi.ebay.com/Bosch-Dishwasher-Service-Repair-Manual-/250480379703. \015\012 ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

My lg dishwasher LD-14AW2 is not starting. It turns on and displays the time but when I click on anything it double bings and nothing happens. I have cleaned out the filters and my husband has removed the drain hose from the s band and it was all clean. the display looks normal...no error code. Do you have any idea what the problem could be?


Tunr power off 20 min then back on see if this helps ... Dishwashers

Pressure Washer Purchased in 2001. Used about 30 hours. It is very hard to start if at all. Good gas, good spark plug. Sometimes it will start within 50-100 pulls. After getting started, if you release hose trigger it will cut off. Any suggestions of what else to do? Thanks in advance.


I would look into getting the carb rebuilt, sounds like there is some gummed up valves. ... Pressure Washers

Good Morning, I have a LG dishwasher, model LD-2052SH. The included water supply hose is 1.5 metres long, I would like to purchase a 2.5 metre long hose. Could you please give me details as to where I could obtain the hose. Thanking you in anticipation.


... LG Dishwashers

Hello could you tell me how to start my Proline integrated dishwasher IDW8AP-U i have lost the manual I remember when I first used it i could not work out how to start it so I looked it up in the manu


... Dishwashers

I have a danby ddw496w that leaks water from the bottom of the machine when it goes into the drain cycle.it will start coming out the bottom as well as the drain outlet .Could it be a simple hose connection or is there something else that could cause this effect.the rear hoses are tight and it runs fine and does not leak untill it drains


Ditto- same issue, hoses are tight, just leaks through the bottom while draining. Anyone with advice? I just bought mine used, and the previous owner is willing to buy a replacement part, we just have to figure out what we need... ... Danby DDW496W Free-Standing Dishwasher

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

My dish washer isn't cleaning the dishes well. There are little particals inside of every cup and on dishes after it is done. I just emptied and and now I'm running it with bleach. But before I started it I looked at the drain hose under the sink. The drain hose had water in it. The drain hose is going uphill from the dishwasher to the sink so I don't know if this is normal to have some water in the drain hose when the washer completes since it's not would have to pump uphill to get to the garba


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

When i start my pressure washer it sprays good, but when i stop and then start spraying again, theres no presure.have to shut down and take hose off and start again.


... Pressure Washers

I have a GE black panel dishwasher. I am having trouble cleaning the panel. It looks like cleaner has dripped down it but no matter what I use it never looks any better. The panel sounds like hard plastic and is in perfectly good shape. It just looks bad. I've tried soap and water and other cleaners but nothing helps.


There is a cheap way to replace the panel and that is on applianceart.com. They have replacement panels and covers, and even stainless steel. ... GE GSD53 Dishwasher

WHEM I START MY IGNIS DISHWASHER IT STARTS TO FILL THEN FROM THE RIGHT HAND CORNER CLEAN WATER STARTS TO LEAK OUT . I LOOKED AT THE DOOR SEALS AND THEY SEEM FINE I HAVE ALSO PUT IN A NEW FLOAT SWITCH AND STILL THE SAME PROBLEM ! COULD IT BE THE INLET VALVE ? HELP THANKS MANDY


It sounds like it overfilling,it may be a preesure switch problem.if you turn the dishwasher off the valve should stop if it doesnt then its the valvle.you may have to try cleaning the sunp under the filter.it may be clogged with sludge stopping the ... Dishwashers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0893 seconds