Having problems with your KitchenAid Dishwashers ?

Remove the Impeller on the motor of dishwasher

\015 I need to get to the seals on the Motor of the KitchenAid dishwasher. In order to do this I have to remove the impeller from the motor. this is a KitchenAid dishwasher model # KUDS01DJBT0 Serial # FK3501342.\015

Answers :

Here is a diagram:
70a2091.gif
Hello. the best source for correct parts is Sears direct. Go to this link
\015\012http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?modelNumber=KUDS01DJBT0&pathTaken=partSearch
Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore 17362 dishwasher was making a bad noise and now the motor seems to be locked up. I might have already un-jammed the motor by removing the cover on the bottom (inside), and turning the knife impeller on the outside of the screen, but I can see lint type material in the hole on the other side of the impeller. Hard to explain, but it is in the hole in the center of the unit and there is a screen like the knife impeller has behind it. I could clean this lint if I could get the door off. How


... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

Hobart model # C44 old dishwasher, wash pump motor will not remove impeller will not clear the hole, how to remove the impeller?


... Dishwashers

Remove the Impeller on the motor of dishwasher


(old question but might help someone in future)How to take screw of dish washer impeller:Impeller heats up when the heater at the bottom runs... so maybe impeller melts a bit and sticks on the screw.Heat\012 up the impeller with a ... Dishwashers

Remove the Impeller on the motor of dishwasher


Here is a diagram: ... KitchenAid Dishwashers

LG LDF8812ST dishwasher not washing: reports LE error code. Fills and drains ok. Impeller is clear, removed inside housing - no obstructions. Synchronous motor works. Tested main motor - appears to be good. Motor is not locked, looks to be in excellent condition. No shorts to ground, continuity across three main pins - not sure what the other 4 are for. My guess would be the PCB, but not sure how to test this. How do I determine if the PCB is bad?


... LG LDF9810ST Built-in Dishwasher

Asea Cylinda 1400 dishwasher leaking underneath. Found wash pump seal leaking. Have removed pump and motor but can't remove impeller to get to seal.


... Dishwashers

Kenmore Model 1590 Dishwasher, 1985, sitting unused since about 1994. Takes water into tub but never goes through any washing/rinsing cycles; water stands in bottom (I stop it below door level). A click, like a solenoid activation from the timer area, but motor never does anything. Removed the shroud covering what I assume is the impeller, which was stuck, but freed it by turning several times...made no difference. Suggestions??


... Kenmore Dishwashers

How do i remove the impeller from the motor - KitchenAid Dishwashers


... KitchenAid Dishwashers

All aspects of the dishwasher work except the wash motor/pump does not run. Is it the motor? I have taken the lower arm assembly apart and removed the support to spin the impeller. It spins fine although there is axial play.


If the shaft is moveing from side to side you need to replace the motor. did you tern the impeller around about 3 complet terns? ... Dishwashers

How do i remove the impeller from my kenmore dishwasher motor in order to replace the seal? it is leaking.


... Kenmore Dishwashers

My dishwasher impeller failed----just was loose in the drawer. i ordered part 525884P, motor rotor assy which has arrived from new zealand. but, there were no instructions on how to remove previous assembly and install the new. are instructions available? steve nute


First fold the racks on the side of the drawer up out of the wayThen Remove the cutlery basketThen with the drawer fully open grab the main rack from the front and pull upward, You will need to persuade it past the rinse aid d ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Pump disassembly Can't remove drain impeller from shaft. Need to replace motor shaft seal on Maytag dishwasher mod. DWC7302AAB


I removed the impeller on my DW761UQB. The instructions were molded into the plastic pump housing. This is how I DID MINE: Remove motor mount screws. Remove the chopper screw (screw only goes into impeller, not motor shaft). Remove chopper and rotate ... Dishwashers

The dishwasher started making horrendous noises. I removed the bottom panel and narrowed the noise down to the motor (the noise starts and stops when the motor kicks on and off). How do I remove the motor to visually check it out? I thought I had all of the screws removed, but it feels like something is still holding it in place. thanks My model number is GSD4060N10SS (GE Dishwasher)


... General Electric GSD4060NSS Built-in Dishwasher

Kenmore Dishwasher Model #110703412 leaks, likely around the motor shaft. Are there motor shafts seals and how are they replaced? Does the motor assembly remove through the tub or does it require being removed from the bottom? Do you have to remove the dishwasher from the cabinet to do this job?


... Kenmore Dishwashers

Asko 1375 unit will not wash drains and fills ok  motor at back of unit runs well. Suspect impeller   Does motor have to come off for impeller replacement?? My 1375 is leaking a bit, looks like the seal which was mentioned in the impeller repair case,may be the problem? The other problem I noted was a clogged screen at the bottom of the dishwasher which is on the suction side of the pump, the screen had calcium buildup etc. I cleaned it off with vinigar and reran the dishwasher seemed ot fix th


Do you mean to say that the washer does not go into the wash cycle at all, or washes poorly?An answer to both can be found HERE.This article ... Asko 1375 Dishwasher

I have a Maytag MDB7100AWW dishwasher that makes a lot of noise from the motor at the end of the drain cycle. When there is water in the dishwasher it doesn't make any noise and washes well. This url (http://www.applianceaid.com/maytag-dish-noise.html) describes my problem exactly but I can't remove this part. I have unscrewed the 3 screws keeping it in place but it seems to be still attached to the motor. How can I remove it?


... Maytag MDB7100AWB Dishwasher

Bosch dishwasher SHU3032 UC/14. The soap dispenser does not open. In the past I've used dishwasher magic or similar to clean the dishwasher of hardwater deposits and that solved the problem. The cover opens and closes manually. The springs seem fine. I removed the door skin and the linkages look good. I checked the resistance on the Wax motor and it is with in spec, approximately 2150ohms. I 've watched the cycle and the wax motor never seems to actuate. I put my meter on th


... Bosch Dishwashers

Kitchen Aid Dishwasher KUDR24SEBLO does not drain 100%. I have removed the drain hose and chcked the sink P-Trap, [it drains thru the garbage disposer]. Unit is 10 years old, otherwise works fine. I am having difficulty removing the impeller and items above the pump to see if it is clogged. Do you think I have a partially clogged pump or a timer issue that prevents the pump from completely emptying the bottom of the dishwasher? We have run the dishwasher 20-30 times since observing the problem.


Hi there,\012Please check out the following -Pump - Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pu ... KitchenAid Dishwashers

Maytag diswasher MDB6600AWW Sprayer arms don't spin. Dishwasher makes all the right noises, except for spraying. Water fills properly and heats up. Water drains properly. Found paper on the back of access panel. Ran Manual Function and Field Service tests, no problems indicated. Disassembled all the pieces inside the bottom of the dishwasher. No obviously damaged parts. Shaft for motor turns freely. It seems like the parts that attach from the impeller to the motor shaft don't


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

ASKO 1555 dishwasher won't run. The anti flood device motor won't stop running but we've removed all the water. All the lights on the front panel blink in unison and when we hold down the start/cancel button on the front, nothing resets. We can't run our dishwasher. We've tried disconnecting power and resetting the circuit breaker but the churning motor won't stop.


Hello,Welcome to FixYa.Based on your description " The anti flood device motor won\\'t stop running but we\\'ve removed all the water " It is likely nothing very serious. ... Asko 24 in. 1805 Built-in Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

Plumber installed new garbage disposal without removing plug. Dishwasher ran all night without draining. I removed plug and it drained but now the dishwasher doesn't have water coming out of sprays. Is the motor burned out?


Spray's are most likely clogged with food debris,carefully use a small nail or similar object to clean them out. ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

Dishwasher notworking am 14c dishwasher but the motor does not work im sure this isthe issuebut is ther any instruction on how to remove the motor


Is really very easy, remove the two screws and use them to push it out screw them in the two holes whit treads and thats it. (sorry my english, i´m from mexico) ... Hobart AM14C-155 Dishwasher

The dishwasher will not drain. The motor hums. We have tried to remove the central unit inside the dishwasher, but cannot remove the inner black disk --it has a bolt, but we cannot get a good grip to twist it out. We suspect that under the mesh covering is a lot of gunk that needs to be cleaned out.


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1787 seconds