Having problems with your KitchenAid Dishwashers ?

I have a kitchenaid dishwasher mod KUDK01TKBL1. It was running fine, opened the door and now the unit is dead,no lights nothing. It has 119 volts to it, the circuit board has line voltage and the door switch seems okay. I could not find any thermal fuse in this unit


Answers :

Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kitchenaid dishwasher mod KUDK01TKBL1. It was running fine, opened the door and now the unit is dead,no lights nothing. It has 119 volts to it, the circuit board has line voltage and the door switch seems okay. I could not find any thermal fuse in this unit


... KitchenAid Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

Amana model ADB1500AWW, start/cancel touch pad does not work...power to unit...wash cycles can be selected. Could it possibly be a door switch?..touch pad or circuit board?


... Amana Dishwashers

I have a new Hotpoint Dishwasher HDA2000T00WW. Ran it once. Now it seems to have no power. Nothing starts. Disconnect switch is on and line voltage observed at connections to dishwasher. Does this have a reset button on motor which may have been tripped? Any other possible things I could check?


... Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

No voltage to water inlet valve, overfill switch seems ok and door switch seems ok. I am thinking the timer, but everything else seems to work fine is there something i am overlooking?


\015\012Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU).\015\012Check all hoses for possible leaks.\015\012 ... Roper Dishwashers

I removed an old dishwasher and replaced it with this GE 24" Profile GSD533ODO1WW unit. It seems to run through the cycles like it should but it doesn't seem to run any water for some reason. I hooked up a new water line to it and turned it on. There where no leaks that I could see. Is there any installation manual that you could send me to make sure that I didn't miss anything or is there anything that you can tell me that I should look for? Thanks, Jesse


... Dishwashers

Candy a8001/1 uk the dishwasher fills and runs for 10 mins then stops. the heating element is heating ok and i have checked the door switch and it seems to be functioning ok but if i open and close the door it will run for a couple of secounds and stop again could you tell me what could be the cause of this?


... Candy Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

Whirlpool dishwasher model # DU1055KTP34--washer stopped mid-cycle---no power at panel---removed panel and checked door switches--one showed 5 volts and switched other showed line voltage and switched


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Kenmore 17362 dishwasher was making a bad noise and now the motor seems to be locked up. I might have already un-jammed the motor by removing the cover on the bottom (inside), and turning the knife impeller on the outside of the screen, but I can see lint type material in the hole on the other side of the impeller. Hard to explain, but it is in the hole in the center of the unit and there is a screen like the knife impeller has behind it. I could clean this lint if I could get the door off. How


... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

I have a whirlpool portable dishwasher model # dp940pwpq2. I think it stopped working in middle of cycle has standing water in bottom no power to front control unit door seems to close and latch properly, not sure if it's door switch or control s thermal fuse doesn't look bad any ideas?


... Whirlpool DP940PWSQ Free-Standing Dishwasher

Hello i have a hobart autosoft glass washer, it just keeps filling up with water even when switched off. when its switched on it dose same. i dont know if it could be a vale in the plastic container where the water comes though on the back of the unit or if it is due to some thing on the circuit board. Cheers .


... Dishwashers

GLDB958AQ0 Lights on panel light up then go off after a few seconds upon startup. Sometimes they stay on and the timer in the display window counts down the minutes, but in either case no sounds come from the dishwasher nor does any water enter the unit. The water is turned on and there are no kinks in the supply line. I removed the water valve and could not blow through it. Upon applying current to the valve I could blow through it but it still seemed restricted. Should I be able to blow thr


... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

I have an older under the counter high temp dish washer not sure the model number but it has the three switches on the lower left, has both upper and lower wands and it is high temp. Not for sure but it seem like the homing cam switch is not working you can manually turn the came to get machine working but when it shuts off it wont restart when you close and latch the door could you please help!


The cam switch may be faulty and may be available for replacement.\015\012\015\012Hard to find replacement without model no. but for the current model it is available ... Moyer Diebel Dishwashers

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

Rinse Aid dispenser seems to use a lot of product. Could almost need to be refilled daily. Is there somewhere or somehow to determine where an internal leak may be or to check that the rinse aid door is leaking or is not the problem. This seemed to happen very suddenly. This unit is approx. 6-7 years old. The rinse aid settings have not been changed.


Turn the settings down. the amountof rise aid dispenced. ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

Model mdb7601awb diswasher . Nothing works , no buttons torn on or work when pushed, no action. 1.Have checked power to unit and is ok 2.checked door switches (2) and both work properly. 3. no visual discoloration on circuit board. There is a blue dot on the wiring harness from control board to button panel.When evaluating with magnifing glass I believe this to be blue ink droplet and not any burnning of harness. Need a Guru.


I have had the board replaced 5 times and the entire dishwasher replaced once. It was necessary to go to the state attorney general to get Maytag to extend the warranty. Just called the service center for the sixth time, after this the warranty will ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1549 seconds