Having problems with your KitchenAid Dishwashers ?

I have a kitchen aid dishwasher that is stuck on the clean cycle. It will drain water, but no water seems to be getting into the washer. If i push the start button, cycle will not start. The clean light is the only light that will stay on. the other lights will go on, but they eventually go off without starting the cycle. Is this the thermal fuse???


Answers :

Repair Help & Product Troubleshooting for KitchenAid Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kitchen aid dishwasher that is stuck on the clean cycle. It will drain water, but no water seems to be getting into the washer. If i push the start button, cycle will not start. The clean light is the only light that will stay on. the other lights will go on, but they eventually go off without starting the cycle. Is this the thermal fuse???


... KitchenAid Dishwashers

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

The clean light on my Kitchenaid Dishwasher model KUD124SEBL4, stays on even after opening the door after w wash. Also 4 out of 5 time when you start the dishwasher no water turns on you have to cance


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My dishwasher will start any program, it drains, fills, empties & beeps continually within a few minutes. The rinse light stays on until the machine is turned off & re-set. Aditonally, the ater heating has been hit & miss for some time! A service guy cleaned the water sensor with hot water fro a ketle + tooth brush, but the problem came back after a couple of weeks. Having removed item he cleaned, it looks fine and appears to switch OK. Not sure if its actually faulty. Is the themperature sensor


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

My Bosh Model# SHE4AM02UC/01 Is not cycling. Started with the soap dispenser not opening, progressed to the drain pump not staying on. When you turn it on, the pump runs for 2 seconds. water solenoid opens for another two seconds, and then the "clean" light comes on. If I go to quick wash, or to pot scrubber it might do a regular cycle. I did pull the pump to remove a piece of glass before this all started, but can't imagine that would be the cause.


... Bosch SHE4AM02UC 24 in. Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a modulogic ADP951.seemed to be stuck on cycle today so I stopped it. water did not drain. I cleaned all rotors and filters and re started. Water drained however start light now flashing. Have tried holding for 5 secconds to re start but only starts pumping out water (of which there is none) and then stops. Light continues to blink. Any other tricks??


I am assuming you have not tried the reset by turning mains power off and then on.\015\012\015\012One of the reasons for being stuck in the wash cycle is the water temperature is not reaching the right level. This could be due to heater ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Miele intake/drain light is flashing. It seems to be an intake problem, because water drains out fine, but seconds after water starts going to the machine, it stops and the intake/drain light starts flashing again. We've cleaned the filter in the inflow hose, cleaned the arms, and it still doesn't work. Any suggestions?


... Miele Touchtronic G892 Built-in Dishwasher

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel button i hear a um noise as if it going to turn on but nothing happens and the light stays blinking. what do you think might be the issue .


Dear friend,\015\012ngfam at you service! happy to assist!\015\012It's an electronic problem!The lights are called codes and need to be diagnoed by a factory service person!!We sell appliances for 65 years an ... Dishwashers

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

I have a 7 yr old Miele G 641 SC Plus dishwasher, the inlet/drain light comes on and stops the wash cycle.I have tried cleaning the water inlet filter, drain pump and non return valve many times, the wash cycle then starts with the pump out of existing water and can sometimes go for about 20mins( sometimes happens a soon as the water starts to flow in) into a cycle before stoppinig again with inlet/drain light on.


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Dishwasher will not start, no lights come on. There is also standing water at the bottom. Can you help point me in the right direction? Went to start the dishwasher and none of the controls on the panel are working or lighting up. I checked the fuse box and all fuses are good.


... Frigidaire 24 in. GLD2350RC Energy Star® Built-in Dishwasher

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers

My siemens dishwasher has the water tap indicator light on when washing starts. i have cleaned the water filter and the spray arm but the light doesnt go off and the washing doesnt take place. Instead i can just see water coming into the drain in intervals. what do i do?


... Siemens Dishwashers

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

Intake/Drain light is on. First flashed F13. Cleaned the water intake filter;cleaned the triple filter and drain pump.Light continues to stay on-it seems as if no water in coming in the dishwasher. Water supply is on all the way.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. F13 is a\015\012flow meter error; unfortunately there is no way to reset it so you’ll have to\015\012get ... Miele Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1992 seconds